Batch processes polymerization

Polymerization Reaction Polymerization Process Batch Plug Flow CSTR... 

For a same polymerization process (batch process) smaller particles are generally obtained with styrene compared to BMA. 

A continuous process may include batch make-up of minor reagents, such as the catalyst for a polymerization process. Batch flows into a continuous process are usually labeled Normally no flow and show the flow rates that will be obtained when the stream is flowing. It is these instantaneous flow rates that govern the equipment design, rather than the much lower time-averaged flow rates. 

As already mentioned, the Tg of a copolymer chain is highly influenced by the copolymer composition, chemical composition distribution, and thus also affected by the type of emulsion polymerization process. Batch copolymers usually are... 

The emulsion polymerization process (batch or continuous) is widely used for producing ABS because various grades of ABS resins can be manufactured. In a continuous process, two to six reactors are used in series with rubber latex feed added either to the first reactor or the first two reactors. In a typical ABS emulsion process, the styrene/acrylonitrile copolymer (SAN) and polybutadiene (PBL) are separately prepared by emulsion pro-... 

Emulsion Process. The emulsion polymerization process utilizes water as a continuous phase with the reactants suspended as microscopic particles. This low viscosity system allows facile mixing and heat transfer for control purposes. An emulsifier is generally employed to stabilize the water insoluble monomers and other reactants, and to prevent reactor fouling. With SAN the system is composed of water, monomers, chain-transfer agents for molecular weight control, emulsifiers, and initiators. Both batch and semibatch processes are employed. Copolymerization is normally carried out at 60 to 100°C to conversions of - 97%. Lower temperature polymerization can be achieved with redox-initiator systems (51). 

PVDE is manufactured using radical initiated batch polymerization processes in aqueous emulsion or suspension operating pressures may range from 1 to 20 MPa (10—200 atm) and temperatures from 10 to 130°C. Polymerization method, temperature, pressure, recipe ingredients, the manner in which they are added to the reactor, the reactor design, and post-reactor processing are variables that influence product characteristics and quaUty. 

The polymerization of monomers to form hydrocarbon resins is typically carried out by either the direct addition of catalyst to a hydrocarbon fraction or by the addition of feed to a solvent—catalyst slurry or solution. Most commercial manufacturers use a continuous polymerization process as opposed to a batch process. Reactor temperatures are typically in the range of 0—120°C. 

Three bulk polymerization processes are commercially important for the production of methacrylate polymers batch cell casting, continuous casting, and continuous bulk polymerization. Approximately half the worldwide production of bulk polymerized methacrylates is in the form of molding and extmsion compounds, a quarter is in the form of cell cast sheets, and a quarter is in the form of continuous cast sheets. 

As the polymer molecular weight increases, so does the melt viscosity, and the power to the stirrer drive is monitored so that an end point can be determined for each batch. When the desired melt viscosity is reached, the molten polymer is discharged through a bottom valve, often under positive pressure of the blanketing gas, and extmded as a ribbon or as thick strands which are water-quenched and chopped continuously by a set of mechanical knives. Large amounts of PET are also made by continuous polymerization processes. PBT is made both by batch and continuous polymerization processes (79—81). 

A factor in addition to the RTD and temperature distribution that affects the molecular weight distribution (MWD) is the nature of the chemical reaciion. If the period during which the molecule is growing is short compared with the residence time in the reactor, the MWD in a batch reactor is broader than in a CSTR. This situation holds for many free radical and ionic polymerization processes where the reaction intermediates are very short hved. In cases where the growth period is the same as the residence time in the reactor, the MWD is narrower in batch than in CSTR. Polymerizations that have no termination step—for instance, polycondensations—are of this type. This topic is treated by Denbigh (J. Applied Chem., 1, 227 [1951]). 

Polylactides, 18 Poly lactones, 18, 43 Poly(L-lactic acid) (PLLA), 22, 41, 42 preparation of, 99-100 Polymer age, 1 Polymer architecture, 6-9 Polymer chains, nonmesogenic units in, 52 Polymer Chemistry (Stevens), 5 Polymeric chiral catalysts, 473-474 Polymeric materials, history of, 1-2 Polymeric MDI (PMDI), 201, 210, 238 Polymerizations. See also Copolymerization Depolymerization Polyesterification Polymers Prepolymerization Repolymerization Ring-opening polymerization Solid-state polymerization Solution polymerization Solvent-free polymerization Step-grown polymerization processes Vapor-phase deposition polymerization acid chloride, 155-157 ADMET, 4, 10, 431-461 anionic, 149, 174, 177-178 batch, 167 bulk, 166, 331 chain-growth, 4 continuous, 167, 548 coupling, 467 Friedel-Crafts, 332-334 Hoechst, 548 hydrolytic, 150-153 influence of water content on, 151-152, 154... 

In order to be economically viable, a continuous emulsion polymerization process must be able to produce a latex which satisfies application requirements at high rates without frequent disruptions. Since most latex products are developed in batch equipment, the problems associated with converting to continuous systems can be significant. Making such a change requires an understanding of the differences between batch and continuous reactors and how these differences influence product properties and reactor performance. 

In batch or semi-batch polymerization processes it is often desirable to add a "chaser catalyst" towards the end of the reaction to reduce the residual monomer concentration to acceptable levels. The ability of the catalyst to reduce the monomer concentraion to low levels (ca 0.10 vol%) is of considerable importance for economic, envirorunental and physiological reasons. The chaser catalyst addition reduces processing time and increases throughput (Kamath and Sargent (1987)). 

One final note While the techniques used here were applied to control temperature In large, semi-batch polymerization reactors, they are by no means limited to such processes. The Ideas employed here --designing pilot plant control trials to be scalable, calculating transfer functions by time series analysis, and determining the stochastic control algorithm appropriate to the process -- can be applied In a variety of chemical and polymerization process applications. 

Consider again a batch polymerization process where the process is characterized by the sequential execution of a number of steps that take place in the two reactors. These are steps such as initial reactor charge, titration, reaction initiation, polymerization, and transfer. Because much of the critical product quality information is available only at the end of a batch cycle, the data interpretation system has been designed for diagnosis at the end of a cycle. At the end of a particular run, the data are analyzed and the identification of any problems is translated into corrective actions that are implemented for the next cycle. The interpretations of interest include root causes having to do with process problems (e.g., contamination or transfer problems), equipment malfunctions (e.g., valve problems or instrument failures), and step execution problems (e.g., titration too fast or too much catalyst added). The output dimension of the process is large with more than 300 possible root causes. Additional detail on the diagnostic system can be found in Sravana (1994). 

In the suspension polymerization process, the autoclave reactor is filled with water. PVA, polyvinyl alcohol is the dispersing agent that helps stabilize the suspension. Lauroyl peroxide is the free radical catalyst that starts it all off. The reaction temperature is around 130°F, and the process takes 10—12 hours per batch, with 95% conversion. 

Chabot et al. at Atofina Chemicals (King of Prussia, PA, USA) used in-line NIR to monitor monomer conversion in real time in a batch emulsion polymerization process. The business value of this monitoring... 

Polymerization processes involve an infinite set of coupled first-order ordinary equations (PFTR or batch) or coupled algebraic equations (CSTR). 

In ary polymerization process one can terminate the reactions by adding a chemical that stops the reaction or by cooling, and this is frequency done in batch processes (the equations and their solutions for the batch reactor are identical to those for the PFTR with T replaced by t). 

A bnlk polymerization reactor can be as simple as a tube into which the reactants are fed and from which the polymer mixture emerges at the end it can be more of a traditional, continnons stirred-tank reactor (CSTR), or even a high-pressure autoclave-type reactor (see Figure 3.21). A bulk polymerization process need not be continuous, but it should not be confnsed with a batch reaction. There can be batch bnlk polymerizations jnst as there are continnons bulk polymerizations processes. 

The homopolymerization and copolymerization of 4-methyl-l-pent-ene is generally carried out in a batch polymerization process (5). Batch polymerization refers to a polymerization method in which a quantity of the monomers are polymerized in a reaction vessel and then the resulting polymer is recovered from that reaction vessel upon the desired level of polymerization of the monomers. It is desirable to carry out such processes under conditions, which result in a slurry of particles of the desired polymer or copolymer in the polymerization diluent rather than a solution of the polymer or copolymer. The formation of such a slurry aids in the separation and purification of the resulting polymer. 

Particle Size and Shape. The polymerization process for producing macroporous synthetic polymers (539) leads to the formation of spherical particles whose size can be controlled within certain limits. The popular XAD polymers are usually sold with approximately 90 of the total weight encompassing smooth beads with 20-50-mesh sizes. Most users incorporate a suspension step to remove the fines in their purification of the polymer, but they do not remove the small number of particles larger than 20 mesh. The particle size and distribution vary with different polymer batches, and it is advisable to mechanically sieve polymer beads and choose only those within the 20-50-mesh size for preparation of the adsorption columns. 

Polymer Production. Three processes are used to produce nylon-6,6. Two of these start with nylon-6,6 salt, a combination of adipic acid and hexamethylenediamine in water they are the batch or autoclave process and the continuous polymerization process. The third, the solid-phase polymerization process, starts with low molecular weight pellets usually made via the autoclave process, and continues to build the molecular weight of the polymer in a heated inert gas, the temperature of which never reaches the melting point of the polymer. 

---