Polyether Ether Ketone PEEK

Polyether ether ketone (PEEK) (structure B of Table 21.5). This material was first prepared in the laboratories of ICI in 1977 and test marketed in 1978. The material is now marketed by Victrex as Victrex PEEK. 

Polyether ether ketones (PEEK) have been developed using polyethersulphone technology. These materials crystallise, unlike the polysulphones, and have higher maximum service temperatures. They also have better resistance to hydrolysis at elevated temperatures than the polymides. 

The literature proposes a relatively large number of HEX reactors that have been designed and built of different materials such as glass, stainless steel, polyether ether ketone (PEEK), and silicon carbide (SiC). A presentation can be found in Amdoimaz et al. [13]. 

The primary resin of interest is epoxy. Carbon-fiber-epoxy composites represent about 90% of CFRP production. The attractions of epoxy resins are that they polymerize without the generation of condensation products that can cause porosity, they exhibit little volumetric shrinkage during cure which reduces internal stresses, and they are resistant to most chemical environments. Other matrix resins of interest for carbon fibers include the thermosetting phenolics, polyimides, and polybismaleimides, as well as high-temperature thermoplastics such as polyether ether ketone (PEEK), polyethersulfone (PES), and polyphenylene sulfide. 

Matrix materials for commercial composites are mainly liquid thermosetting resins such as polyesters, vinyl esters, epoxy resins, and bismaleimide resins. Thermoplastic composites are made from polyamides, polyether ether ketone (PEEK), polyphenylene sulfide (PPS), polysulfone, polyetherim-ide (PEI), and polyamide-imide (PAI). 

Membrane materials often employed are hydrophobic polysulfone or hydrophilic regenerated cellulose or cellulose acetate other materials are nylon, polytetrafluoro-ethylene (PTFE, Teflon), polyether ether ketone (PEEK) or poly(divinyl fluoride) (PDVF). 

Polyether ether ketone (PEEK) and Polyether sulphone (PES) belong to the most recent developments in the field of technical high-performance polymers. Both possess very good thermal and mechanical properties, which can be further improved by reinforcing fibres. Their application is mainly in aircraft and space vehicles. 

Sulfonation is very useful chemical modification of polymer, as it induces high polarity in the polymer changing its chemical as well as physical properties. Sulfonated polymers are also important precursors for ionomer formation [75]. There are reports of sulfonation of ethylene-propylene diene terpolymer (EPDM) [76, 77], polyarylene-ether-sulfone [78], polyaromatic ether ketone [79], polyether ether ketone (PEEK) [80], styrene-ethylene-butylene-styrene block copolymer, (SEBS) [81]. Poly [bis(3-methyl phenoxy) phosphozene] [82], Sulfonated polymers show a distinct peak at 1176 cm"1 due to stretching vibration of 0=S=0 in the -S03H group. Another peak appears at 881 cm 1 due to stretching vibration of S-OH bond. However, the position of different vibrational bands due to sulfonation depends on the nature of the cations as well as types of solvents [75, 76]. 

The HPLC is connected by red polyether ether ketone (PEEK) tubing to the NMR flow cell which is inside the magnet. With shielded cryomagnets or ultra-shielded magnets the HPLC can be as close as 30-50 cm to the magnet versus... 

High purity 4,4 -diphenoxy benzophenone is a key starting material for the production of high molecular weight polymers. Thus, its polycondensation with terephtaloyl chloride in presence of Friedel-Crafts catalyst gives polyether-ether ketones (PEEK) with the structure depicted on scheme 17 ... 

Gruman has developed an automated triangular truss-type beam builder using graphite-reinforced polyether sulfone. This beam can be formed in outerspace at the rate of 1.5m per min. from flat stock which is heated and forced continuously around a die. The sections are Induction welded and may be protected from deterioration by the application of a coating of polyether ether ketone (PEEK).(30)... 

Polyether ether ketone PEEK 315°C For high temperature parts and wear resistance, e.g., bushings and valve seats... 

Coupling of LC to NMR is relatively simple. The effluent from the column is delivered through a polyether-ether ketone (PEEK) transfer line to the NMR flow cell, which typically has a volume of 60 jA. The measurement can be carried out in one of four modes on-flow, stop-flow, time-sliced and loop collection. In the on-flow mode, the effluent from the column flows continuously through the NMR flow cell. Because of the very short time available for the measurement when peaks elute in real time, this approach is limited to major components of a mixture. In the stop flow mode, peaks detected with a UV detector are transferred to the NMR flow cell, and the run is automatically stopped. The NMR spectra can then be acquired over a period of several minutes, hours or even days. In the time-sliced mode, the elution is stopped several times during the elution of the peak of interest. This mode is usually used when two analytes are poorly resolved. In the loop collection mode, the chromatographic peaks are stored in loops for offline NMR study. This approach is therefore not a real online hyphenated technique. 

Besides graphite, carbon and glass fibers, organic fibers, e.g., Kevlar, have also been used to reinforce thermosetting resins, e.g., epoxy resin (38). One of the newest developments is fiber-reinforced thermoplastics, e.g., carbon fiber-reinforced polyether ether ketone (PEEK) ( ). These materials are rather tough as demonstrated in the interlaminar toughness values (Table... 

Polymer Specimens. The materials used in this work were polyimide (PI),polyamide-imide (PAl), polyether-ether-ketone (PEEK), polyphenylene sulfide (PPS) and polyether sulphone (PES). The chemical formulas and physical properties of the specimen polymers are summarized in Table I. The specimen polymers, except PPS, were unfilled while the PPS specimen was filled with glass fiber of Uo wt. %. PAI and PES are amorphous polymer with considerably high glass temperature. The polymers, except PI, can flow at hi temperatures and allow the use of injection molding. 

The polyether ether ketone (PEEK) was test marketed in 1978 by ICl. 

More recently, thermoplastics such as polyphenylene sulfide (PPS), polyether sulfone, and polyether ether ketone (PEEK) have entered the primary structures market in competition with thermosets. 

Polyether ether ketone (PEEK) has been considered for use as insulators and cable jackets. The use of PEEK as an insulator allows thinner overall diameters and permits a higher level of continuous operating temperature. The extreme hardness and toughness of PEEK may also eliminate the need of a metal sheath for cable jacket. 

A new process for uniaxial solid-state orientation, using a range of compressive forces and temperatures, has been developed to produce stock sheets of polyether-ether ketone (PEEK) for machining dental implants with substantially increased strength and modulus as compared to their unoriented counterparts. 

In terms of polymer matrices for composite materials, there will be a compromise between solvent and water resistance. Thus non-polar resins are likely to be less resistant to hydrocarbon solvents, which have low polarity, but more resistant to moisture absorption. Polar resins behave in the opposite way. Strongly polar solvents, such as dimethyl sulphoxide or similar, can interact with polar structures in the resin and are difficult to resist. Crystalline thermoplastic polymers are often better for such applications. For example, polyethene will only dissolve in hydrocarbon solvents (of similar solubility parameter) at temperatures above the crystalline melting point. Polar semi-crystalline polymers such as the polyamides or nylons can be dissolved in highly polar solvents, such as cresol, because of a stronger interaction than that between molecules within the crystallites. High performance thermoplastic polymers such as polyether ether ketone (PEEK) have been promoted for their resistance to organic solvents (see Table 3.5) [12], The chemical resistance of unsaturated polyester and vinyl ester and urethane resins is indicated in Table 3.6 [15]. 

Intrinsically non-flammable polymers are few, but phenolic resins have a good reputation both in Are and smoke performance, which has resulted in their becoming increasingly favoured for reinforced plastics structures, for example, underground transport, where such concerns are greatest. Polyether ether ketone (PEEK) is also a low fire and smoke polymer. Unsaturated polyesters, vinyl esters and epoxy resins bum readily, but modified versions are available with improved behaviour. For example, both bromine and chlorine are used extensively in the form of chlorendic (HET) acid, tetrachlorophthalic anhydride (TCPA) and tetrabromo-phthalic anhydride (TBPA) which can be reacted into the polyester in small quantities and can act as permanent (non-migrating) flame retardants. 

Polyether ether ketone (PEEK) has poor resistance to UV. Reinforced grades are available and, where some degree of UV resistance is required, carbon black may be added. Polyphenylene oxide (PPO) and polysulfone are susceptible to photodegradation due to their aromatic content, although PPO in its usual form as a stabilized polymer alloy is somewhat better. It is inadvisable to use any of these polymers for prolonged exposure without protection. 

---