Poly sulfones general

Sinclair-Koppers Co. Lexan 125 bisphenol A polycarbonate from General Electric Co. Polysulfone aromatic poly(sulfone-ether) from Union Carbide Corp. and PPO poly(2,6-dimethyl-p-phenylene oxide) from General Electric Co. 

Low-molecular-weight PES and poly(sulfone) resins in general may cause irritations of eye, skin, and digestive tract. 

The general approaches for the synthesis of poly(arylene ether)s include electrophilic aromatic substitution, nucleophilic aromatic substitution, and metal-catalyzed coupling reactions. Poly(arylene ether sulfone)s and poly(arylene ether ketone)s have quite similar structures and properties, and the synthesis approaches are quite similar in many respects. However, most of the poly(arylene ether sul-fone)s are amorphous while some of the poly(arylene ether)s are semicrystalline, which requires different reaction conditions and approaches to the synthesis of these two polymer families in many cases. In the following sections, the methods for the synthesis of these two families will be reviewed. 

The SnAt reactions were first successfully used in the synthesis of high-molecular-weight poly(arylene etherjs by Johnson et al.4,5 This reaction represents a good example for poly(ether sulfonejs in general, either in laboratory -or industrial-scale preparations. In this procedure, the bisphenol A and sodium hydroxide with an exact mole ratio of 1 2 were dissolved into dimethyl sulfoxide (DMSO)-chlorobenzene. The bisphenol A was converted into disodium bisphenolate A, and water was removed by azeotropic distillation. After the formation of the anhydrous disodium bisphenolate A, an equal molar amount of 4,4,-dichlorodiphenyl sulfone (DCDPS) was added in chlorobenzene under anhydrous conditions and the temperature was increased to 160°C for over 1 h... 

Poly (ary lene ether sulfone)s and poly(arylene ether ketone) have been employed to prepare block and graft copolymers. Generally, the block copolymers can be prepared by reacting functional-group-terminated oligomers with other functional oligomers and monomers. 

One of the first fictional fluoropolymers was poly-1,2,2-trifluorostyrene. On one hand, it has much better oxidation and chemical resistance in comparison with common hydrocarbon polymers and, on the other hand, a wide range of functional groups can be attached to the aromatic ring. A sulfonated polymer was successfully used as a membrane for fuel cells by General Electric Co.3... 

This paper reviews some of our work on general methods for the synthesis of polyaromatics containing either terminal or pendant styrene groups and their thermal polymerization. The examples provided in this paper refer to an aromatic polyether sulfone (PSU) and poly-(2,6-dimethy1-1,4-phenylene oxide) (PPO). 

Of all the hydrocarbon-based PEMs, this group most likely has the largest variety of different systems. This is probably due to the wealth of prior knowledge of the nonsulfonated analogues that have been developed over the last several decades as well as the general expectation of higher thermal stability, better mechanical properties, and increased oxidative stability over polystyrene-based systems. Within the context of this section, polyarylenes are systems in which an aryl or heteroaryl ring is part of the main chain of the polymer. This section will, therefore, include polymers such as sulfonated poly (ether ether ketone) and sulfonated poly(imides) but will not include systems such as sulfonated polystyrene, which will be covered in Section 3.3.I.3. 

Direct copolymerization of sulfonated monomers has been used to synthesize sulfonated poly (benzimidazoles), poly(benzoxazole)s, and poly(benzothia-zole)s. As an example, Kim et al. synthesized poly-(benzthiazole)s from 2,5-diamino-1,4-benzenedithiol dihydrochloride and either 2-sulfoterethphthalic acid sodium salt, 5-sulfoisophthalic acid sodium salt, or 2,4-disulfoisophthalic acid potassium salt in poly-phosphoric acid (PPA), as shown in Figure 34. Similar sulfonated poly(benzimidazole) and sulfonated poly(benzoxazole) ° structures have also been synthesized. A general synthetic scheme for each is shown in Figure 35. The stability of these polymers in aqueous acidic environments appears... 

An early commercial interest in poly (olefin sulfones) was sparked by the low raw materials cost, but this interest waned when it became apparent that thermal instability is a general characteristic of this class of materials. In 1970 Brown and O Donnell reported that poly (butene-1-sulfone) is degraded by gamma radiation with a G(s) approaching 10, making it one of the most radiation-sensitive polymers known (38-39). The potential for use of this radiation sensitivity in the design of electron beam resists was quickly realized by several members of the electronics industry. Bell Laboratories, RCA, and IBM published studies demonstrating the potential of poly (alkene... 

Because of the angled structure of poly(arylene ether sulfone)s, they generally do not crystallize. They are thus amorphous and optically transparent with glass transition temperatures between 150-200 °C. They are soluble in some polar solvents, hydrolysis resistant, and inherently flame resistant. Fields of application for these materials are found particularly in the area of electronics and membrane technology. 

---