PMMA, additives

For PMMA/additive dissolutions, it was not possible to identify any additive characteristic mass peaks, either by direct laser desorption or with matrix-assistance (dithranol, DHBA or sinapinic acid, 4-hydroxy-3,5-dimethoxy-cinnamic acid). This has again been ascribed to very strong interaction between PMMA and additives, which suppresses desorption of additive molecules. Also, partial depolymerisation of pho-tolytically labile PMMA by laser irradiation may play a role, which leads to saturation of the detector by PMMA fragment-ions and disappearance of additive mass peaks below noise level. Meyer-Dulheuer [55] has also reported MALDI-TOFMS analysis of a coating/2-ethylhexyldiphenylphosphate sample. Quantitative determination of the additives by means of MALDI-ToFMS proved impossible. Possibly the development of reproducible (automated) sample handling procedures or thin films might overcome this problem. 

Elashmawi, I. R, Hakeem, N.A., (2008), Effect of PMMA Addition on Characterization and Morphology of PVDF, Polymer Engineering Science, Vol. 48, p>p. 895-901, ISSN 1548-2634. 

Figure 6. Scanning force images of a blend of 75 % PMMA and 25 % PSl 00 at room temperature and 97 °C. Adhesive force histograms taken from adhesive force images show two pronounced peaks at 27 °C and 97 C, which indicates no change in adhesive forces during heating. The PSIOO areas (marked by circles) have lower adhesives force ((terker) Aan the surrounding PMMA. Additional smaller droplets with a diameter of about 300 nm are visible.

PVC EVA EVA-g-PMMA blends and EVA-g-PMMA addition to PVC/EVA blends showed improved strength and toughness ... 

PC ABS PMMA PMMA addition to ABS/PC blends gave improved notched toughness and tensile strength 72... 

McNeill 11,12) has established that the initial step when a transition metal halide is combined with PMMA is coordination of the metal ion to the carbonyl oxygens of the polymer. This is usually followed by the loss of methyl halide and the formation of a metal polymethacrylate. TGA/IR has provided interesting means to probe these systems to compare results using manganese chloride IS) and chromium (111) diloride 19) as PMMA additives. Weight loss data and identification of the evolved gases for both additives are rqwrted below in Table 1. 

The cured polymers are hard, clear, and glassy thermoplastic resins with high tensile strengths. The polymers, because of their highly polar stmcture, exhibit excellent adhesion to a wide variety of substrate combinations. They tend to be somewhat britde and have only low to moderate impact and peel strengths. The addition of fillers such as poly (methyl methacrylate) (PMMA) reduces the brittleness somewhat. Newer formulations are now available that contain dissolved elastomeric materials of various types. These mbber-modifted products have been found to offer adhesive bonds of considerably improved toughness (3,4). 

PMMA-impregnated sol—gel-derived siUca gels have also been examined (54). Long-wave uv illumination was employed in addition to benzoyl peroxide for PMMA polymerization. This method prohibited the degradation of the siUca xerogel from moisture adsorption and desorption. Overall the material behaved more like bulk PMMA than bulk siUca, with the exception of hardness. 

The toughness of interfaces between immiscible amorphous polymers without any coupling agent has been the subject of a number of recent studies [15-18]. The width of a polymer/polymer interface is known to be controlled by the Flory-Huggins interaction parameter x between the two polymers. The value of x between a random copolymer and a homopolymer can be adjusted by changing the copolymer composition, so the main experimental protocol has been to measure the interface toughness between a copolymer and a homopolymer as a function of copolymer composition. In addition, the interface width has been measured by neutron reflection. Four different experimental systems have been used, all containing styrene. Schnell et al. studied PS joined to random copolymers of styrene with bromostyrene and styrene with paramethyl styrene [17,18]. Benkoski et al. joined polystyrene to a random copolymer of styrene with vinyl pyridine (PS/PS-r-PVP) [16], whilst Brown joined PMMA to a random copolymer of styrene with methacrylate (PMMA/PS-r-PMMA) [15]. The results of the latter study are shown in Fig. 9. 

Fig. 21. High-resolution XPS spectra of PMMA spin-coated onto (a) silicon and (b,c) iron. The C(ls) spectnim of PMMA on silicon was explained by four components but an additional component was needed to explain the C(ls) spectrum of PMMA on iron. Reproduced by permission of Gordon and Breach Science Publishers from Ref. [24].

Friedrich et al. also used XPS to investigate the mechanisms responsible for adhesion between evaporated metal films and polymer substrates [28]. They suggested that the products formed at the metal/polymer interface were determined by redox reactions occurring between the metal and polymer. In particular, it was shown that carbonyl groups in polymers could react with chromium. Thus, a layer of chromium that was 0.4 nm in thickness decreased the carbonyl content on the surface of polyethylene terephthalate (PET) or polymethylmethacrylate (PMMA) by about 8% but decreased the carbonyl content on the surface of polycarbonate (PC) by 77%. The C(ls) and 0(ls) spectra of PC before and after evaporation of chromium onto the surface are shown in Fig. 22. Before evaporation of chromium, the C(ls) spectra consisted of two components near 284.6 eV that were assigned to carbon atoms in the benzene rings and in the methyl groups. Two additional... 

Yamamoto and Minamizaki [159] disclose the use of a curable silicone based release agent blended with resin particles which swell or are soluble in organic solvent. Coatings made with such blends can be written on with solvent based inks. For example, an addition cure silicone network containing 20 wt% 0.1 p,m diameter PMMA particles exhibited both good writeability (no ink dewetting and smear free) and a low release force of 10 g/cm for a PSA tape. 

Further aspects of the reaction of aromatic tertiary hydroxyl amines have been examined by more sophisticated techniques [49]. 2-Methyl-2-nitrosopropane was used as a radical trap, and the endgroups on PMMA resulting from its addition were detectable by ultraviolet spectroscopy. Electron spin resonance results on the same system have also been reported [50]. 

An example of this improvement in toughness can be demonstrated by the addition of Vamac B-124, an ethylene/methyl acrylate copolymer from DuPont, to ethyl cyanoacrylate [24-26]. Three model instant adhesive formulations, a control without any polymeric additive (A), a formulation with poly(methyl methacrylate) (PMMA) (B), and a formulation with Vamac B-124 (C), are shown in Table 4. The formulation with PMMA, a thermoplastic which is added to modify viscosity, was included to determine if the addition of any polymer, not only rubbers, could improve the toughness properties of an alkyl cyanoacrylate instant adhesive. To demonstrate an improvement in toughness, the three formulations were tested for impact strength, 180° peel strength, and lapshear adhesive strength on steel specimens, before and after thermal exposure at 121°C. 

The data also demonstrate that the addition of the thermoplastic, PMMA, does not have the significant effect on the toughness or adhesion properties as does the addition of the rubber, Vamac B-124. Clearly, the physical properties of the polymeric additive determine the magnitude of the adhesive physical property modifications, which result from their addition to an alkyl cyanoacrylate monomer. 

The producer of column No. 6 tried to supplementary remove admixtures from the gel matrix by applying liquid extractions. He revealed that the extraction process was very slow and that the apparently clean material started to bleed again after some time or when the temperature of extraction was raised. This result indicates that the retention properties of SEC columns may change in the course of their use as a result of cleaning their surface. Maybe the recipes for the gel synthesis will have to be modified to suppress the effects of additives. It seems that the producer of column No. 5 is not far from the ideal situation, at least for the PMMA-toluene system. We cannot exclude... 

The effects of increasing the concentration of initiator (i.e., increased conversion, decreased M , and broader PDi) and of reducing the reaction temperature (i.e., decreased conversion, increased M , and narrower PDi) for the polymerizations in ambient-temperature ionic liquids are the same as observed in conventional solvents. May et al. have reported similar results and in addition used NMR to investigate the stereochemistry of the PMMA produced in [BMIM][PFgj. They found that the stereochemistry was almost identical to that for PMMA produced by free radical polymerization in conventional solvents [43]. The homopolymerization and copolymerization of several other monomers were also reported. Similarly to the findings of Noda and Watanabe, the polymer was in many cases not soluble in the ionic liquid and thus phase-separated [43, 44]. 

Studies of PMMA-based ionomers also demonstrate the influence of thermal treatment on deformation modes (16). For Na salts of PMMA-based ionomers of 6 and 12 mol% that were cast from DMF, only crazes were observed on straining. However, after an additional heat treatment (48 h at 160°C), which also removes any DMF solvent that is present, shear deformation zones are induced. Hence, the ionic cluster phase, which was destroyed by the polar solvent, has been restored by the heat treatment. 

The combined effects of a divalent Ca counterion and thermal treatment can be seen from studies of PMMA-based ionomers [16]. In thin films of Ca-salts of this ionomer cast from methylene chloride, and having an ion content of only 0.8 mol%, the only observed deformation was a series of long, localized crazes, similar to those seen in the PMMA homopolymer. When the ionomer samples were subject to an additional heat treatment (8 h at 100°C), the induced crazes were shorter in length and shear deformation zones were present. This behavior implies that the heat treatment enhanced the formation of ionic aggregates and increased the entanglement strand density. The deformation pattern attained is rather similar to that of Na salts having an ion content of about 6 mol% hence, substitution of divalent Ca for monovalent Na permits comparable deformation modes, including some shear, to be obtained at much lower ion contents. 

Recently, various polyesters such as poly(ethylene adipate), poly(tetramethylene adipate), poly(caprolac-tone), and poly(aliphatic carbonate), having terminal hydroxyl groups, were reacted with ACPC to give corresponding macroazoesters and their thermal behaviors were observed by DSC [14]. The block copolymers of these polycondensation polymers with addition polymers such as PSt and PMMA were synthesized [14]. 

Polyarylate (PAR)-b-PSt and PAR-b-PMMA for compatibiiizers are described 135,39,40). The addition of PAR-b-PSt (1-10 parts) to 100 parts of a blend of PAR-PSt (7w-3w) resulted in improvement of the tensile and flexural modulus (Fig. 4), and PSt dispersed particles were diminished from 1-5 microns to an order that is undetectable by SEM, indicating the excellent, compatibilizing effect of the block copolymer. The alloy thus formed exert the characteristic of PAR, an engineering plastic, as well as easy processability of PSt. Addition of PAR-b-PMMA (3 or 8 parts) to 100 parts of a blend of PAR-polyvinylidenefluoride (PVDF) (7w-3w) resulted in improved microdispersed state of PVDF due to compatibility of PMMA with PVDF, while segregation of PVDF onto the surface was controlled. 

An outstanding property of EPS is its extremely low density (when compared to other processes), that by alteration of the preforming treatment can be varied according to the end use. Other types of plastics are employed to produce expandable plastic foam (EPF), including PE, PP, PMMA, and ethylene-styrene copolymers. They can use the same equipment, with only slight modifications. These plastics have different properties from those of EPS and open up different markets. They provide improved sound insulation, resistances to additional heat deformation, better recovery of shapes in moldings, and so on. 

The Arrhenius frequency factors [log(T/M V)] for addition of carbon centered radicals to the unsubstiUited terminus of monosubslituted or 1,1-disubstituted olefins cover a limited range (6.0-9.0), depend primarily on the steric demand of the attacking radical and are generally unaffected by remote alkene substituents. Typical values of log(T/M" V) are ca 6.5 for tertiary polymeric (e.g. PMMA ), ca 7.0 for secondary polymeric (PS, PMA, and ca 7.5, 8.0 and 8.5 for small tertiary (e.g. /-C4H9 ), secondary (i-CiH ) and primary (CHj, CbHs ) radicals respectively (Section 4.5.4).4 For 1,2,2-trisubstituted alkenes the frequency factors arc about an order of magnitude lower.4 The trend in values is consistent with expectation based on Iheoretical calculations. 

Addition of TEMPO post-polymerization to a methacrylate polymerization provides an unsaturated chain end (Scheme 9.52)i07 sw presumably by disproportionation of the PMMA propagating radical with the nitroxide. For polymers based on monosubstituted monomers (PS,1 0" PBA59,[Pg.534]

---