Plasmas, atomic spectroscopy

Fassel, V. A. and Bear, B. R. (1986) Ultrasonic nebuUzation of liquids for analytical inductively coupled plasma atomic spectroscopy an update. Spectrochim. Acta B, 41,1089-113. (1995/96) PE Atomic Spectroscopy Supplies Catalog. 

Table 7 Ion mass fractions of K. marxianus and M thermoautotrophicum determined by plasma atomic spectroscopy. Reproduced from Reference [28] with permission of the author and publisher.

Because light emitted from inductively coupled plasma torches is characteristic of the elements present, the torches were originally introduced for instruments that optically measured the frequencies and intensities of the emitted light and used them, rather than ions, to estimate the amounts and types of elements present (inductively coupled plasma atomic emission spectroscopy. 

To examine a sample by inductively coupled plasma mass spectrometry (ICP/MS) or inductively coupled plasma atomic-emission spectroscopy (ICP/AES) the sample must be transported into the flame of a plasma torch. Once in the flame, sample molecules are literally ripped apart to form ions of their constituent elements. These fragmentation and ionization processes are described in Chapters 6 and 14. To introduce samples into the center of the (plasma) flame, they must be transported there as gases, as finely dispersed droplets of a solution, or as fine particulate matter. The various methods of sample introduction are described here in three parts — A, B, and C Chapters 15, 16, and 17 — to cover gases, solutions (liquids), and solids. Some types of sample inlets are multipurpose and can be used with gases and liquids or with liquids and solids, but others have been designed specifically for only one kind of analysis. However, the principles governing the operation of inlet systems fall into a small number of categories. This chapter discusses specifically substances that are normally liquids at ambient temperatures. This sort of inlet is the commonest in analytical work. 

Inductively coupled plasma atomic emission spectroscopy... 

For inductively coupled plasma atomic emission spectroscopy (ICP-AES) the sample is normally in solution but may be a fine particulate solid or even a gas. If it is a solution, this is nebulized, resulting in a fine spray or aerosol, in flowing argon gas. The aerosol is introduced into a plasma torch, illustrated in Figure 3.21. 

Figure 3.21 A plasma torch for inductively coupled plasma atomic emission spectroscopy...

Oxygen and nitrogen also are deterrnined by conductivity or chromatographic techniques following a hot vacuum extraction or inert-gas fusion of hafnium with a noble metal (25,26). Nitrogen also may be deterrnined by the Kjeldahl technique (19). Phosphoms is determined by phosphine evolution and flame-emission detection. Chloride is determined indirecdy by atomic absorption or x-ray spectroscopy, or at higher levels by a selective-ion electrode. Fluoride can be determined similarly (27,28). Uranium and U-235 have been determined by inductively coupled plasma mass spectroscopy (29). 

Small concentrations of iron can also be deterrnined by flame atomic absorption and inductively coupled plasma emission spectroscopies (see... 

X-ray fluorescence, mass spectroscopy, emission spectrography, and ion-conductive plasma—atomic emission spectroscopy (icp—aes) are used in specialized laboratories equipped for handling radioisotopes with these instmments. 

Aluminum is best detected quaUtatively by optical emission spectroscopy. SoHds can be vaporized direcdy in a d-c arc and solutions can be dried on a carbon electrode. Alternatively, aluminum can be detected by plasma emission spectroscopy using an inductively coupled argon plasma or a d-c plasma. Atomic absorption using an aluminum hoUow cathode lamp is also an unambiguous and sensitive quaUtative method for determining alurninum. 

The sodium hydroxide is titrated with HCl. In a thermometric titration (92), the sibcate solution is treated first with hydrochloric acid to measure Na20 and then with hydrofluoric acid to determine precipitated Si02. Lower sibca concentrations are measured with the sibcomolybdate colorimetric method or instmmental techniques. X-ray fluorescence, atomic absorption and plasma emission spectroscopies, ion-selective electrodes, and ion chromatography are utilized to detect principal components as weU as trace cationic and anionic impurities. Eourier transform infrared, ft-nmr, laser Raman, and x-ray... 

Plasma atomic emission spectrometry is also employed as a detection method for gc (see Plasma technology). By monitoring selected emission lines a kind of selective detection based on elemental composition can be achieved (see Spectroscopy). 

The classical wet-chemical quaUtative identification of chromium is accompHshed by the intense red-violet color that develops when aqueous Cr(VI) reacts with (5)-diphenylcarba2ide under acidic conditions (95). This test is sensitive to 0.003 ppm Cr, and the reagent is also useful for quantitative analysis of trace quantities of Cr (96). Instmmental quaUtative identification is possible using inductively coupled argon plasma—atomic emission spectroscopy... 

Instrumental Quantitative Analysis. Methods such as x-ray spectroscopy, oaes, and naa do not necessarily require pretreatment of samples to soluble forms. Only reUable and verified standards are needed. Other instmmental methods that can be used to determine a wide range of chromium concentrations are atomic absorption spectroscopy (aas), flame photometry, icap-aes, and direct current plasma—atomic emission spectroscopy (dcp-aes). These methods caimot distinguish the oxidation states of chromium, and speciation at trace levels usually requires a previous wet-chemical separation. However, the instmmental methods are preferred over (3)-diphenylcarbazide for trace chromium concentrations, because of the difficulty of oxidizing very small quantities of Cr(III). 

In Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP-OES), a gaseous, solid (as fine particles), or liquid (as an aerosol) sample is directed into the center of a gaseous plasma. The sample is vaporized, atomized, and partially ionized in the plasma. Atoms and ions are excited and emit light at characteristic wavelengths in the ultraviolet or visible region of the spectrum. The emission line intensities are proportional to the concentration of each element in the sample. A grating spectrometer is used for either simultaneous or sequential multielement analysis. The concentration of each element is determined from measured intensities via calibration with standards. 

R. K. Winge, V A. Fassel, V. J. Peterson, and M. A. Floyd. Inductively Coupled Plasma Atomic Emission Spectroscopy An Atlas of Spectral Information. Elsevier, Amsrerdam, 1985. ICP-OES specrral scans near emission lines usefol for analysis. 

The XRD and TEM showed that the bimetallic nanoparticles with Ag-core/Rh-shell structure spontaneously form by the physical mixture of Ag and Rh nanoparticles. Luo et al. [168] carried out structure characterization of carbon-supported Au/Pt catalysts with different bimetallic compositions by XRD and direct current plasma-atomic emission spectroscopy. The bimetallic nanoparticles were alloy. Au-core/Pd-shell structure of bimetallic nanoparticles, prepared by co-reduction of Au(III) and Pd(II) precursors in toluene, were well supported by XRD data [119]. Pt/Cu bimetallic nanoparticles can be prepared by the co-reduction of H2PtClg and CuCl2 with hydrazine in w/o microemulsions of water/CTAB/ isooctane/n-butanol [112]. XRD results showed that there is only one peak in the pattern of bimetallic nanoparticles, corresponding to the (111) plane of the PtCu3 bulk alloy. 

Plasma sources were developed for emission spectrometric analysis in the late-1960s. Commercial inductively coupled and d.c. plasma spectrometers were introduced in the mid-1970s. By comparison with AAS, atomic plasma emission spectroscopy (APES) can achieve simultaneous multi-element measurement, while maintaining a wide dynamic measurement range and high sensitivities and selectivities over background elements. As a result of the wide variety of radiation sources, optical atomic emission spectrometry is very suitable for multi-element trace determinations. With several techniques, absolute detection limits are below the ng level. 

A. Montaser and D.W. Golightly, Inductively Coupled Plasmas in Analytical Atomic Spectroscopy, VCH, New York, NY (1992). 

Allen LB, Siitonen PH, Thompson HC Jr. 1998. Determination of copper, lead, and nickel in edible oils by plasma and furnace atomic spectroscopies. Journal of the American Oil Chemists Society 75(4) 477-481. 

---