Photoelectron Auger electron spectroscopy

Electronic spectra of surfaces can give information about what species are present and their valence states. X-ray photoelectron spectroscopy (XPS) and its variant, ESC A, are commonly used. Figure VIII-11 shows the application to an A1 surface and Fig. XVIII-6, to the more complicated case of Mo supported on TiOi [37] Fig. XVIII-7 shows the detection of photochemically produced Br atoms on Pt(lll) [38]. Other spectroscopies that bear on the chemical state of adsorbed species include (see Table VIII-1) photoelectron spectroscopy (PES) [39-41], angle resolved PES or ARPES [42], and Auger electron spectroscopy (AES) [43-47]. Spectroscopic detection of adsorbed hydrogen is difficult, and... 

Powell C J, Jablonski A, Tilinin I S, Tanuma S and Penn D R 1999 Surface sensitivity of Auger-electron spectroscopy and x-ray photoelectron spectroscopy J. Eiectron Spec. Reiat. Phenom. 98-9 1... 

Powell C J 1994 Inelastic interactions of electrons with surfaces applications to Auger-electron spectroscopy and x-ray photoelectron spectroscopy Surf. Sc/. 299-300 34... 

Figure 8.1 Processes occurring in (a) ultraviolet photoelectron spectroscopy (UPS), (b) X-ray photoelectron spectroscopy (XPS) and (c) Auger electron spectroscopy (AES)...

X-ray Photoelectron Spectroscopy. X-ray photoelectron spectroscopy (xps) and Auger electron spectroscopy (aes) are related techniques (19) that are initiated with the same fundamental event, the stimulated ejection of an electron from a surface. The fundamental aspects of these techniques will be discussed separately, but since the instmmental needs required to perform such methods are similar, xps and aes instmmentation will be discussed together. 

C. L. Wilson, Comprehensive Analytical Chemisty Ultraviolet Photoelectron and Photoion Spectroscopy Auger Electron Spectroscopy Plasma Excitation in SpectrochemicalAnalysis, Vol. 9, Elsevier Science, Inc., New York, 1979. 

In other articles in this section, a method of analysis is described called Secondary Ion Mass Spectrometry (SIMS), in which material is sputtered from a surface using an ion beam and the minor components that are ejected as positive or negative ions are analyzed by a mass spectrometer. Over the past few years, methods that post-ion-ize the major neutral components ejected from surfaces under ion-beam or laser bombardment have been introduced because of the improved quantitative aspects obtainable by analyzing the major ejected channel. These techniques include SALI, Sputter-Initiated Resonance Ionization Spectroscopy (SIRIS), and Sputtered Neutral Mass Spectrometry (SNMS) or electron-gas post-ionization. Post-ionization techniques for surface analysis have received widespread interest because of their increased sensitivity, compared to more traditional surface analysis techniques, such as X-Ray Photoelectron Spectroscopy (XPS) and Auger Electron Spectroscopy (AES), and their more reliable quantitation, compared to SIMS. 

Roughness from sputtering causes loss of depth resolution in depth profiling for Auger Electron Spectroscopy (AES), X-Ray Photoelectron Spectroscopy (XPS), and SIMS. 

Surface analysis has made enormous contributions to the field of adhesion science. It enabled investigators to probe fundamental aspects of adhesion such as the composition of anodic oxides on metals, the surface composition of polymers that have been pretreated by etching, the nature of reactions occurring at the interface between a primer and a substrate or between a primer and an adhesive, and the orientation of molecules adsorbed onto substrates. Surface analysis has also enabled adhesion scientists to determine the mechanisms responsible for failure of adhesive bonds, especially after exposure to aggressive environments. The objective of this chapter is to review the principals of surface analysis techniques including attenuated total reflection (ATR) and reflection-absorption (RAIR) infrared spectroscopy. X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), and secondary ion mass spectrometry (SIMS) and to present examples of the application of each technique to important problems in adhesion science. 

ASTM El078, Standard guide for procedures for specimen preparation, mounting, and analysis in auger electron spectroscopy. X-ray photoelectron spectroscopy, and secondary ion mass spectrometry. ASTM, West Conshohocken, PA. 

The most widely used techniques for surface analysis are Auger electron spectroscopy (AES), x-ray photoelectron spectroscopy (XPS), secondary ion mass spectroscopy (SIMS), Raman and infrared spectroscopy, and contact angle measurement. Some of these techniques have the ability to determine the composition of the outermost atomic layers, although each technique possesses its own special advantages and disadvantages. 

Further structural information is available from physical methods of surface analysis such as scanning electron microscopy (SEM), X-ray photoelectron or Auger electron spectroscopy (XPS), or secondary-ion mass spectrometry (SIMS), and transmission or reflectance IR and UV/VIS spectroscopy. The application of both electroanalytical and surface spectroscopic methods has been thoroughly reviewed and appropriate methods are given in most of the references of this chapter. 

The application of surface analytical techniques, most notably X-ray Photoelectron Spectroscopy (XPS) and Auger Electron Spectroscopy (AES), or its spatially resolved counterpart. Scanning Auger Microanalysis (SAM), is of great value in understanding the performance of a catalyst. However, the results obtained from any of these techniques are often difficult to interpret, especially when only one technique is used by itself. 

Size reduction of metal particles results in several changes of the physico-chemical properties. The primary change is observed in the electronic properties of the metal particles which can be characterized by ultraviolet and X-ray photoelectron spectroscopy (UPS and XPS, respectively) as well as Auger-electron spectroscopy (AES) measurements. Furthermore, morphology of the metal nanoparticles is highly sensitive to the environment, such as ion-metal interaction (e.g. metal-support interaction)... 

X-ray photoelectron spectroscopy (XPS) XPS and X-ray-excited Auger electron spectroscopy (XE-AES) measurements were performed with a Perkin Elmer F 5600ci at a working pressure lower than 1027 Pa at the Department of Inorganic Organometallic and Analytical Chemistry in Padova (Italy). 

Spoto, G. and E. Ciliberto (2000), X-ray photoelectron spectroscopy and Auger electron spectroscopy in art and archaeology, in Ciliberto, E. and G. Spoto (eds.), Modern Analytical Methods in Art and Archaeology, Chemical Analysis Series, Vol. 155, Wiley, New York, pp. 363 404. 

Low-Energy Electron Diffraction, X-ray Photoelectron Spectroscopy, and Auger Electron Spectroscopy... 

The elemental composition, oxidation state, and coordination environment of species on surfaces can be determined by X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) techniques. Both techniques have a penetration depth of 5-20 atomic layers. Especially XPS is commonly used in characterization of electrocatalysts. One common example is the identification and quantification of surface functional groups such as nitrogen species found on carbon-based catalysts.26-29 Secondary Ion Mass spectrometry (SIMS) and Ion Scattering Spectroscopy are alternatives which are more surface sensitive. They can provide information about the surface composition as well as the chemical bonding information from molecular clusters and have been used in characterization of cathode electrodes.30,31 They can also be used for depth profiling purposes. The quantification of the information, however, is rather difficult.32... 

---