Palladium solvents

Dissolve 7 g. of pure oleic acid in 30 ml. of dry ethyl chloride (chloroform may be used but is less satisfactory), and ozonise at about —30°. Remove the solvent under reduced pressure, dissolve the residue in 50 ml. of dry methyl alcohol and hydrogenate as for adipic dialdehyde in the presence of 0 5 g. of palladium - calcium carbonate. Warm the resulting solution for 30 minutes with a slight excess of semicarbazide acetate and pour into water. Collect the precipitated semicarbazones and dry the... 

In a lOOmL round-bottomed flask fitted with a magnetic stirrer is placed a mixture of palladium (II) chloride (89mg, O.Smmol), p-benzoquinone (5.94g, 55mmol) and 7 1 dimethylformamide/water (20mL). To the solution, t-decene [substitute safrole for this compound) (7.0g, 50mmc4) is added in 10 min and the mixture is stirred at room temperature for 7h. The solution is poured into cold 3 normal hydrochloric acid (lOOmL) and extracted with 5 portions of ether. The extracts are combined and washed with three portions of 10% aqueous sodium hydroxide solution and a portion of brine, and then dried After removal of the solvent, the residue is distilled to give 2-decanone [P2P] yield 6.1g (78%). 

The method is basically an application of the Wacker oxidation except that the catalyst used is palladium acetate ( Pd(AcO)2 or Pd(02CCH3)2). the solvent is acetic acid or tert-butyl alcohol and the oxygen source is the previously suggested hydrogen peroxide (H202)[17]. 

During the reaction, the palladium catalyst is reduced. It is reoxidized by a co-catalyst system such as cupric chloride and oxygen. The products are acryhc acid in a carboxyUc acid-anhydride mixture or acryUc esters in an alcohoHc solvent. Reaction products also include significant amounts of 3-acryloxypropionic acid [24615-84-7] and alkyl 3-alkoxypropionates, which can be converted thermally to the corresponding acrylates (23,98). The overall reaction may be represented by ... 

More recently, a commercial process has been introduced for the manufacture of methyl isocyanate (MIC) which involves the dehydrogenation of /V-m ethyl form am i de [123-39-7] in the presence of palladium, platinum [7440-06-4], or mthenium [7440-18-8], at temperatures between 50—300°C (31). Aprotic solvents, such as ben2ene [71-43-2], xylenes, or toluene [108-88-3], may optionally be used. A variation of this synthesis employs stoichiometric amounts of palladium chloride [7647-10-1], PdCl2. 

Ceramic, Metal, and Liquid Membranes. The discussion so far implies that membrane materials are organic polymers and, in fact, the vast majority of membranes used commercially are polymer based. However, interest in membranes formed from less conventional materials has increased. Ceramic membranes, a special class of microporous membranes, are being used in ultrafHtration and microfiltration appHcations, for which solvent resistance and thermal stabHity are required. Dense metal membranes, particularly palladium membranes, are being considered for the separation of hydrogen from gas mixtures, and supported or emulsified Hquid films are being developed for coupled and facHitated transport processes. 

The PGM concentrate is attacked with aqua regia to dissolve gold, platinum, and palladium. The more insoluble metals, iridium, rhodium, mthenium, and osmium remain as a residue. Gold is recovered from the aqua regia solution either by reduction to the metallic form with ferrous salts or by solvent-extraction methods. The solution is then treated with ammonium chloride to produce a precipitate of ammonium hexachloroplatinate(IV),... 

A low temperature catalytic process has been reported (64). The process involves the divalent nickel- or zero-valent palladium-catalyzed self-condensation of halothiophenols in an alcohol solvent. The preferred halothiophenol is -bromothiophenol. The relatively poor solubiHty of PPS under the mild reaction conditions results in the synthesis of only low molecular weight PPS. An advantage afforded by the mild reaction conditions is that of making telecheHc PPS with functional groups that may not survive typical PPS polymerization conditions. 

More conveniently, compound (13) was directly condensed with barbituric acid (14) in acetic acid (28) or in the presence of an acid catalyst in an organic solvent (29). The same a2o dye intermediate (13) and alloxantin give riboflavin in the presence of palladium on charcoal in alcohoHc hydrochloric acid under nitrogen. This reaction may involve the reduction of the a2o group to the (9-phenylenediamine by the alloxantin, which is dehydrogenated to alloxan (see Urea) (30). 

Arsonium salts have found considerable use in analytical chemistry. One such use involves the extraction of a metal complex in aqueous solution with tetraphenyiarsonium chloride in an organic solvent. Titanium(IV) thiocyanate [35787-79-2] (157) and copper(II) thiocyanate [15192-76-4] (158) in hydrochloric acid solution have been extracted using tetraphenyiarsonium chloride in chloroform solution in this manner, and the Ti(IV) and Cu(II) thiocyanates deterrnined spectrophotometricaHy. Cobalt, palladium, tungsten, niobium, and molybdenum have been deterrnined in a similar manner. In addition to their use for the deterrnination of metals, anions such as perchlorate and perrhenate have been deterrnined as arsonium salts. Tetraphenyiarsonium permanganate is the only known insoluble salt of this anion. 

Snia Viscosa. Catalytic air oxidation of toluene gives benzoic acid (qv) in ca 90% yield. The benzoic acid is hydrogenated over a palladium catalyst to cyclohexanecarboxyhc acid [98-89-5]. This is converted directiy to cmde caprolactam by nitrosation with nitrosylsulfuric acid, which is produced by conventional absorption of NO in oleum. Normally, the reaction mass is neutralized with ammonia to form 4 kg ammonium sulfate per kilogram of caprolactam (16). In a no-sulfate version of the process, the reaction mass is diluted with water and is extracted with an alkylphenol solvent. The aqueous phase is decomposed by thermal means for recovery of sulfur dioxide, which is recycled (17). The basic process chemistry is as follows ... 

Hydrogenation of Acetylenes. Complete hydrogenation of acetylenes to the corresponding alkanes, which maybe requited to remove acetylenic species from a mixture, or as a part of a multistep synthesis, may be accompHshed using <5 wt % palladium or platinum on alumina in a nonreactive solvent under very mild conditions, ie, <100°C, <1 MPa (10 atm). Platinum is preferred in those cases where it is desired to avoid isomeri2ation of the intermediate olefin. Silver on alumina also can be used in this appHcation as can unsupported platinum metal. 

The catalyst commonly used in this method is 5 wt % palladium supported on barium sulfate inhibited with quinoline—sulfur, thiourea, or thiophene to prevent reduction of the product aldehyde. A procedure is found in the Hterature (57). Suitable solvents are toluene, benzene, and xylene used under reflux conditions. Interestingly, it is now thought that Rosenmund s method (59) originally was successful because of the presence of sulfur compounds in the xylene used, since the need for an inhibitor to reduce catalyst activity was not described until three years later (60). 

For more selective hydrogenations, supported 5—10 wt % palladium on activated carbon is preferred for reductions in which ring hydrogenation is not wanted. Mild conditions, a neutral solvent, and a stoichiometric amount of hydrogen are used to avoid ring hydrogenation. There are also appHcations for 35—40 wt % cobalt on kieselguhr, copper chromite (nonpromoted or promoted with barium), 5—10 wt % platinum on activated carbon, platinum (IV) oxide (Adams catalyst), and rhenium heptasulfide. Alcohol yields can sometimes be increased by the use of nonpolar (nonacidic) solvents and small amounts of bases, such as tertiary amines, which act as catalyst inhibitors. 

This reaction is favored by moderate temperatures (100—150°C), low pressures, and acidic solvents. High activity catalysts such as 5—10 wt % palladium on activated carbon or barium sulfate, high activity Raney nickel, or copper chromite (nonpromoted or promoted with barium) can be used. Palladium catalysts are recommended for the reduction of aromatic aldehydes, such as that of benzaldehyde to toluene. 

An acidic solvent is recommended for use with palladium. Other catalysts that have been used for this reduction include copper chromite and any of the three Raney catalysts, cobalt, iron, or nickel. 

Palladium and platinum (5—10 wt % on activated carbon) can be used with a variety of solvents as can copper carbonate on siHca and 60 wt % nickel on kieselguhr. The same is tme of nonsupported catalysts copper chromite, rhenium (VII) sulfide, rhenium (VI) oxide, and any of the Raney catalysts, copper, iron, or nickel. 

With hydrogen sulfide at 500—600°C, monochlorotoluenes form the corresponding thiophenol derivatives (30). In the presence of palladium catalysts and carbon monoxide, monochlorotoluenes undergo carbonylation at 150—300°C and 0.1—20 MPa (1—200 atm) to give carboxyHc acids (31). Oxidative coupling of -chlorotoluene to form 4,4 -dimethylbiphenyl can be achieved in the presence of an organonickel catalyst, generated in situ, and zinc in dipolar aprotic solvents such as dimethyl acetamide (32,33). An example is shown in equation 4. 

Another alternative method to produce sebacic acid iavolves a four-step process. First, butadiene [106-99-0] is oxycarbonylated to methyl pentadienoate which is then dimerized, usiag a palladium catalyst, to give a triply unsaturated dimethyl sebacate iatermediate. This unsaturated iatermediate is hydrogenated to dimethyl sebacate which can be hydrolyzed to sebacic acid. Small amounts of branched chain isomers are removed through solvent crystallizations giving sebacic acid purities of greater than 98% (66). 

Use of DMF as a solvent for the oxidation of l-o1efins has been reported by Clement and Selwitz. The method requires only a catalytic amount of PdCl2 and gives satisfactory yields under mild conditions. A small amount of olefin migration product is the only noticeable contaminant in the cases reported. The procedure can be applied satisfactorily to various 1-olefins with other functional groups. This useful synthetic method for the preparation of methyl ketones has been applied extensively in the syntheses of natural products such as steroids,macrolides, dihydrojasmone, and muscone. " A comprehensive review article on the palladium-catalyzed oxidation of olefins has... 

The solvent is conveniently that in which the hydrogenation is to be done. During the reduction of the palladium chloride, a neutral solvent is to be preferred any acid or alkali needed for the hydrogenation is added after reduction of the catalyst. 

The presence of hydrogen chloride during the hydrogenation of many organic compounds is desirable or without effect, so that the washing operations may be omitted in such cases. Thus, the palladium chloride on carbon may be used in the same manner as the prereduced catalysts, i.e., simply added before reduction to the solvent and the hydrogen acceptor. 

---