Raney nickel activity

Approximately 60 g of Raney nickel activated catalyst (supplied as a 50% slurry in water, pH 10 by Aldrich Chemical Company) was washed twice with ethanol (150 ml) and added to a solution of 15.9 g of V in 500 ml of ethanol. The mixture was stirred at room temperature for two hours. An additional 18 g of Raney nickel was added, and the mixture was stirred at room temperature for three hours. Following workup, 9.11 g (83.4%) of crude ethyl 2,6,6-trimethylcyclohex-2-ene-l-carboxylate (VII) sufficiently pure for the next step was obtained. 

Raney nickel, activated mix NiCl2-6H20 Pb02 ZnO Pb304 SrO... 

NiCl2 6H20 NiS04-6H20 Raney nickel, activated mix Ca(OH)2 Fe... 

Active Raney nickel induces desulfurization of many sulfur-containing heterocycles thiazoles are fairly labile toward this ring cleavage agent. The reaction occurs apparently by two competing mechanisms (481) in the first, favored by alkaline conditions, ring fission occurs before desul-, furization, whereas in the second, favored by the use of neutral catalyst, the initial desulfurization is followed by fission of a C-N bond and formation of carbonyl derivatives by hydrolysis (Scheme 95). 

In past years, metals in dilute sulfuric acid were used to produce the nascent hydrogen reductant (42). Today, the reducing agent is hydrogen in the presence of a catalyst. Nickel, preferably Raney nickel (34), chromium or molybdenum promoted nickel (43), or supported precious metals such as platinum or palladium (35,44) on activated carbon, or the oxides of these metals (36,45), are used as catalysts. Other catalysts have been suggested such as molybdenum and platinum sulfide (46,47), or a platinum—nithenium mixture (48). 

CatalyticaHy Active Species. The most common catalyticaHy active materials are metals, metal oxides, and metal sulfides. OccasionaHy, these are used in pure form examples are Raney nickel, used for fat hydrogenation, and y-Al O, used for ethanol dehydration. More often the catalyticaHy active component is highly dispersed on the surface of a support and may constitute no more than about 1% of the total catalyst. The main reason for dispersing the catalytic species is the expense. The expensive material must be accessible to reactants, and this requires that most of the catalytic material be present at a surface. This is possible only if the material is dispersed as minute particles, as smaH as 1 nm in diameter and even less. It is not practical to use minute... 

This reaction is favored by moderate temperatures (100—150°C), low pressures, and acidic solvents. High activity catalysts such as 5—10 wt % palladium on activated carbon or barium sulfate, high activity Raney nickel, or copper chromite (nonpromoted or promoted with barium) can be used. Palladium catalysts are recommended for the reduction of aromatic aldehydes, such as that of benzaldehyde to toluene. 

The anticonvulsant primidone (1035) resembles phenobarbital but lacks the 2-oxo substituent. It was introduced in 1952 and has remained a valuable drug for controlling grand mal and psychomotor epilepsy. As might be expected, primidone is metabolized to yield phenobarbital (1034 X = 0) and C-ethyl-C-phenylmalondiamide (1036), both of which have marked anticonvulsant properties however, primidone does have intrinsic activity and an appropriate mixture of its metabolites has only a fraction of its activity (73MI21303). Primidone may be made in several ways, of which desulfurization by Raney nickel of the 2-thiobarbiturate (1034 X = S) or treatment of the diamide (1036) with formic acid (at 190 °C) seem to be the most satisfactory (54JCS3263). 

In addition, the steric configuration can be obtained by Raney nickel desulfurization to optically active aliphatic acids of known con-figuration. 2 2 Combined with the quasi racemate method this... 

Two different sets of experimental conditions have been used. Buu-Hoi et al. and Hansen have employed the method introduced by Papa et using Raney nickel alloy directly for the desulfurization in an alkaline medium. Under these conditions most functional groups are removed and this method is most convenient for the preparation of aliphatic acids. The other method uses Raney nickel catalysts of different reactivity in various solvents such as aqueous ammonia, alcohol, ether, or acetone. The solvent and activity of the catalyst can have an appreciable influence on yields and types of compounds formed, but have not yet been investigated in detail. In acetic anhydride, for instance, desulfurization of thiophenes does not occur and these reaction conditions have been employed for reductive acetylation of nitrothiophenes. Even under the mildest conditions, all double bonds are hydrogenated and all halogens removed. Nitro and oxime groups are reduced to amines. 

Raney cobalt is generally less effective than Raney nickel, but may be of use when the rupture of other bonds must be avoided. The important use of Raney nickel desulfurization for the structure determination of thiophenes and for the determination of the absolute configuration of optically active thiophene and benzene derivatives has been stressed earlier. 

In addition to the Raney nickel catalysts, Raney catalysts derived from iron, cobalt, and copper have been examined for their action on pyridine. At the boiling point of pyridine, degassed Raney iron gave only a very small yield of 2,2 -bipyridine but the activity of iron in this reaction is doubtful as the catalyst was subsequently found to contain 1.44% of nickel. Traces of 2,2 -bipyridine (detected spectroscopically) were formed from pyridine and a degassed, Raney cobalt catalyst but several Raney copper catalysts failed to produce detectable quantities of 2,2 -bipyridine following heating with pyridine. 

---