Painting solvent resistance

These pigments are sensitive to heat and bleed ia most paint solvents. They are, however, resistant to acids and bases. Their tinctorial strength is considerably greater than that of inorganic yellows but they are weaker than the diaryUde yellows. They are used extensively ia emulsion paints, paper coating compositions, inks (qv), and, depending on particle size, can ia some cases be used outdoors because of excellent lightfastness ia full shades. 

In general, polycarbonate resins have fair chemical resistance to aqueous solutions of acids or bases, as well as to fats and oils. Chemical attack by amines or ammonium hydroxide occurs, however, and aUphatic and aromatic hydrocarbons promote crazing of stressed molded samples. Eor these reasons, care must be exercised in the choice of solvents for painting and coating operations. Eor sheet appHcations, polycarbonate is commonly coated with a sihcone—sihcate hardcoat which provides abrasion resistance as well as increased solvent resistance. Coated films are also available. 

Compounds based on S—EB—S usually contain polypropylene, which improves solvent resistance and processibiUty and raises upper service temperatures. Compounds intended for use in the automotive industry are able to survive 1000 hours air exposure at temperatures of 125°C with only minor changes in properties (54). Very soft compounds have been developed to replace foam mbber for interior trim parts. In this and similar appHcations, these soft compounds are usually insert molded over polypropylene or metal and then coated with flexible polyurethane paint (55). Other automotive appHcations include products intended for sound deadening, flexible air ducts, and gear shifter boots, as weU as improving the properties of sheet mol ding compounds. 

Phenolic resins are useful surface coating materials. Resols are useful for stoving lacquers for coating chemical plant, textile equipment, razor blades, brassware cuid food cans. Phenolic resins are used with poly(vinyl formal) as a flexible, tough and solvent-resistant wire enamel. Oil-soluble resins based on synthetic phenols form the basis of some gloss paints. 

Solvent resistance This varies from very poor (for chlorinated rubbers) to good (for polyurethanes). All paint binders have specific susceptibilities and the presence of small quantities of the appropriate solvent in the atmosphere in the region of an item of plant can cause rapid failure. 

Lifting may also occur if a paint containing strong solvents (xylol or solvent naphtha, not to mention such active solvents as esters and ketones) is applied (not necessarily by brushing) over a paint which is not resistant to them. The older an oxidising paint film becomes, the more solvent-resistant it will be. Short-oil media and pigment-rich paints are not so prone to lifting. This type of failure is not restricted to oil-base materials it can, for example, also occur with chlorinated rubber paints. 

Materials such as polyethylene, polypropylene and acetal, which have waxy surfaces, or other crystalline plastics that are very solvent resistant, can be difficult to paint and require special primers or pre-treatments (flame, etc.) for satisfactory adhesion. Many amorphous plastics easily accept a wide variety of paint coatings. 

This colorant is produced in the USA, where it also plays a minor role on the market. Its shade is a reddish yellow. P.Y.60 is used in trade sales paints and in emulsion paints. Poor resistance to organic solvents, lack of overcoating fastnesss, and a lightfastness that deteriorates rapidly with the degree of reduction with Ti02 are reasons for the limited commercial interest in this pigment. Crystal data are published by A. Whitaker [12],... 

P.R.146 is a bluish red pigment with very good solvent resistance, even compared to other group II Naphthol AS pigments. It is primarily used in printing inks, coatings, and paints. 

Commercially available P.O.46 types are usually quite transparent. They are employed primarily in packaging printing inks, also in offset and metal deco printing. Publication gravure inks, plastics, especially PVC, LDPE, and elastomers, as well as general industrial paints are suitable media for pigment application. P.O.46 is less solvent resistant than P.R.53 1, but it is faster to alkali and acid. In terms of lightfastness, P.O.46 performs poorly 1/3 and 1/25 SD prints equal only step 1 on the Blue Scale. 

This combination gives a very useful blend of mechanical properties. The PBT phase provides melt flow, solvent resistance and the ultimate heat performance of the blend (Tm). The PC phase provides reduced shrink, better dimensional stability, higher heat capability under low load (66 psi HDT) and improved impact strength. Interestingly, the PC also provides improved paint adhesion by being present as a very thin outer layer in molded parts. PBT, by virtue of its solvent... 

All resins except polybutadiene formulated with conventional melamine cross-linkers, applied to SAE 1010 bare steel paint test panels, and baked to yield cross-linked, solvent resistant films. 

SS-LINKED POLYMERS ARE USED in a wide variety of aerospace, automotive, building construction, and consumer product applications. Not all paints, adhesives, composites, and elastomers are cross-linked, but cross-linking systems are often used in these applications when resistance to solvents, resistance to high temperatures, and high mechanical performance are required. These important properties can be traced directly to the three-dimensional interconnected molecular network that is characteristic of cross-linked systems. 

---