Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Packaging facility

Packaging facilities, packaging and labeling, package disposal, workplace refuse disposal, cleanup and disposal of spills. [Pg.1949]

City fire department Packages, packaging machinery, packaging facilities, and materials... [Pg.1949]

An indoor packaging facility handles lubricating oil (an NFPA Class NIB liquid) in drums at atmospheric pressure and temperature. Prior to shipment, the drums are stored in pallets in a warehouse section of the facility. A concern was raised about the explosion and fire potential that may be present from handling combustible liquid inside a building. A lunchroom is adjacent to the packaging facility. [Pg.20]

Alternately, consumer products could be shipped en masse to distribution centers located near the population centers. From here they would be shipped by truck to individual customers. This type of facility has sales advantages. The retailer can be guaranteed that his order will be delivered within 24 hours after its receipt. This allows him to provide excellent customer service with a small warehouse. These centers could receive bulk quantities, but then each one would have to package the product. This would mean a duplication of packaging facilities. [Pg.27]

If the length is twice the diameter, the length will be 17 ft. Similar calculations were performed for the storage preceding the packaging facilities for cartons and drums. [Pg.132]

A C++ include file is a primitive form of package. Header files or groups of them can implement requirements expressed by a Catalysis model package. ANSI C++ has the namespace construct, which provides somewhat better packaging facilities. [Pg.342]

A massive explosion and fire occurred at an agricultural chemical packaging facility in Arkansas, killing three firefighters and injuring a fourth. The likely cause was a supersack of azinphos-methyl (an insecticide) being placed near a hot compressor exhaust pipe. [Pg.202]

Other than aerial application over swamps for mosquito abatement, disulfoton is not known to be used over water. Potential sources of release into surface water include discharge of waste water from disulfoton manufacturing, formulation, and packaging facilities (HSDB 1994). Leaching and runoff from treated fields, pesticide disposal pits, or hazardous waste sites may contaminate both groundwater and surface water with disulfoton. Entry into water can also occur from accidental spills. Small amounts of volatilized disulfoton may be removed from the atmosphere as a result of wet deposition and may enter surface water (Racke 1992). [Pg.145]

Abbott Labs (Chicago, IL) has extensive fermentation, organic synthesis processing, and chemical finishing and packaging facilities and is engaged mainly in production of antibiotics, that is, erythromycin and penicillin, and hundreds of medicinal and fine chemicals. Characteristics of various types of wastes generated from this plant are depicted in Table 20. The typical units involved in the Abbott treatment works are as follows ... [Pg.197]

Wastewater sources from pesticide manufacmring and formulating/packaging facilities have been described in the previous section. This section discusses wastewater quality and quantity. [Pg.511]

However, these reactions do not always occur. In some instances there may be steric factors in the API molecule that restrict access to the reactive group and the reaction does not occur, or occurs at a much-reduced rate. For almost all chemical interactions, a key component is presence of free (unbound) water (23,24). In the absence of a sufficient amount of free water, the reactions do not proceed. This is the basis for using very low humidity manufacturing and packaging facilities for the manufacture of effervescent products. The free water layer serves to dissolve sufficient of the drug and the excipient, or to form bridges between particles, such that the components/reactants come into sufficiently close contact for the reaction to occur. [Pg.101]

Written certification from packaging facility stating that it is in conformance with CGMPs. [Pg.752]

Remedial Investigation at a Herbicide Storage and Packaging Facility— Probabilistic Design Compliance Monitoring—Regulation-Prescribed Sampling... [Pg.14]

Feed to the medical source facility is a composite billet prepared in the sales and industrial source packaging facility. [Pg.274]

The devolatilizer (7) is held under a very high vacuum to remove unreacted monomer and solvent from the polymer melt. The monomer is distilled in the styrene recovery unit (8) and recycled back to the prepolymizer. The polymer melt is then pumped through a die head (9) to form strands, a waterbath (10) to cool the strands, a pelletizer (11) to form pellets and is screened to remove large pellets and fines. The resultant product is air-conveyed to bulk storage and packaging facilities. [Pg.169]

National Fire Protection Association NFPA Packages, packaging facilities, and warehouse designs and operation. [Pg.1707]

There are approximately 330 applicants, of which about 80 have manufacturing and packaging facilities. A unique characteristic is that applicants are required by law to be registered with the SA Pharmacy Council. [Pg.634]

Indirect Labor, Supervision Fringe Benefits Medical Facilities Fire, Safety, Security Waste Treatment Facilities Packaging Facilities Restaurant Facilities Recreation Facilities Salvage Services Quality Control Laboratories Shipping, Receiving Facilities Storage Facilities Maintenance Facilities... [Pg.34]

For personnel involved in manufacture or packaging, facilities for handwashing must be available at a reasonable distance The use of these facilities must be encouraged. [Pg.518]

At the end of the wafer processing, the wafer with the IC devices is inspected for defects and reviewed with relevant metrology. If the defect level is acceptable, the IC wafer is sent to the testing facility, where it is electrically probed to check for electrical performance. Next, the IC wafer is stress tested, which involves operating it at the extremes of its specified typical use conditions. If the IC wafer passes the functional and stress tests, it is sent to the packaging facility, where bond pad... [Pg.772]


See other pages where Packaging facility is mentioned: [Pg.1833]    [Pg.133]    [Pg.84]    [Pg.90]    [Pg.19]    [Pg.386]    [Pg.74]    [Pg.14]    [Pg.16]    [Pg.268]    [Pg.178]    [Pg.1592]    [Pg.604]    [Pg.240]    [Pg.2651]    [Pg.179]    [Pg.2294]    [Pg.2277]    [Pg.1837]    [Pg.830]    [Pg.70]    [Pg.52]   
See also in sourсe #XX -- [ Pg.275 ]




SEARCH



Sales packages facilities

Work package 1 Evaluation of current test procedures and experimental facilities for cyclic oxidation testing

© 2024 chempedia.info