Organic solvents absorption

Crystals from petr ether, mp 99-100°. Practically insol in water sol in most organic solvents. Absorption max 350, 405 nm. 

Carrillo A, Martin-Dominguez IR, Rosas A, Marquez A (2002) Numerical method to evaluate the influence of organic solvent absorption on the conductivity of polymeric composites. Polymer 43 6307-6313... 

NiCls in different organic solvents Absorption spectra of Ni + 158... 

It must be emphasised that the above Tables must be used with caution. The presence of a specific group cannot always be established with certainty from the presence of the absorption band, particularly in the deformation vibration region on the other hand, the absence of the appropriate absorption band indicates that the grouping is not present. The physical state in which the substance is examined may have an appreciable influence the Tables apply generally to dilute solutions in organic solvents (see Table I). 

Endo-exo product mixtures were isolated using the following procedure. A solution of cyclopentadiene (concentration 2-10" M in water and 0.4 M in oiganic solvents) and the dienophile (concentration 1-5 mM) in the appropriate solvent, eventually containing a 0.01 M concentration of catalyst, was stirred at 25 C until the UV-absorption of the dienophile had disappeared. The reaction mixture (diluted with water in the case of the organic solvents) was extracted with ether. The ether layer was washed with water and dried over sodium sulfate. After the evaporation of the ether the... 

THE STATE OF NITRIC ACID IN INERT ORGANIC SOLVENTS The absence of ions in mixtures of acetic acid and nitric acid is shown by their poor electrical conductivity and the Raman spectra of solutions in acetic acid, nitromethane, and chloroform show only the absorptions of the solvent and molecular nitric acid the bands corresponding to the nitronium and nitrate ions cannot be detected. -... 

In general, the peilluoioepoxides have boiling points that are quite similar to those of the corresponding fluoroalkenes. They can be distinguished easily from the olefins by it spectroscopy, specifically by the lack of olefinic absorption and the presence of a characteristic band between 1440 and 1550 cm . The nmr spectra of most of the epoxides have been recorded. Litde physical property data concerning these compounds have been pubhshed (Table 1). The stmcture of HFPO by electron diffraction (13) as well as its solubility and heats of solution in some organic solvents have been measured (14,15). 

Chemica.1 Properties. The FEP resin is inert to most chemicals and solvents, even at elevated temperatures and pressures. However, it reacts with fluorine, molten alkah metal, and molten sodium hydroxide. Acids or bases are not absorbed at 200°C and exposures of one year. The absorption of organic solvents is less than 1% at elevated temperatures and long exposure times. Absorption of chemicals or solvents has no effect on the chemical integrity of the FEP molecule and is a reversible physical process. 

Metal-free, chloroaluminum phthalocyanine [14154-42-8] vanadyl phthalocyanine [13930-88-6], or magnesium phthalocyanines are sufficiently soluble in organic solvents and show enough bleachable absorption at 694.3 nm to serve as repeated Q-switching elements for mby lasers (qv) (180). Phthalocyanines have been used in other lasers as weU (181). 

Noryl is a rigid dimensionally stable material. Dimensional stabiUty results from a combination of low mold shrinkage, low coefficient of thermal expansion (5.9 x 10 per° C), good creep resistance (0.6—0.8% in 300 h at 13.8 MPa (2000 psi)), and the lowest water absorption rate of any of the engineering thermoplastics (0.07% in 24 h at room temperature). Noryl resins are completely stable to hydrolysis. They are not affected by aqueous acids or bases and have good resistance to some organic solvents, but they are attacked by aromatic or chlorinated aUphatic compounds. 

Nitro-substituted indolino spiroben2opyrans or indolino spironaphthopyrans are photochromic when dissolved in organic solvents or polymer matrices (27). Absorption of uv radiation results in the colorless spiro compound [1498-88-0], C22H2gN202, being transformed into the colored, ring-opened species. This colored species is often called a photomerocyanine because of its stmctural similarity to the merocyanine dyes (see Cyanine dyes). Removal of the ultraviolet light source results in thermal reversion to the spiro compound. 

Metal impurities can be determined qualitatively and quantitatively by atomic absorption spectroscopy and the required purification procedures can be formulated. Metal impurities in organic compounds are usually in the form of ionic salts or complexes with organic compounds and very rarely in the form of free metal. If they are present in the latter form then they can be removed by crystallising the organic compound (whereby the insoluble metal can be removed by filtration), or by distillation in which case the metal remains behind with the residue in the distilling flask. If the impurities are in the ionic or complex forms, then extraction of the organic compound in a suitable organic solvent with aqueous acidic or alkaline solutions will reduce their concentration to acceptable levels. 

The substitution of water-borne versions of these primers is increasing as environmental restrictions on the use of organic solvents become stricter. These are generally aqueous emulsions of epoxy novolac or phenolic based resins stabilized by surfactants [34]. Non-ionic surfactants are preferred, as they are non-hygroscopic in the dried primer films. Hygroscopic ionic surfactants could result in excessive water absorption by the primer film in service. 

Other important determinants of the effects of compounds, especially solvents, are their partition coefficients, e.g., blood-tissue partition coefficients, which determine the distribution of the compound in the body. The air-blood partition coefficient is also important for the absorption of a compound because it determines how quickly the compound can be absorbed from the airspace of the lungs into the circulation. An example of a compound that has a high air-blood partition coefficient is trichloroethane (low blood solubility) whereas most organic solvents (e.g., benzene analogues) have low air-blood partition coefficients (high blood solubility). 

Poly[2,5-dialkoxy-l,4-phenylene) vinylenejs with long solubilizing alkoxy chains dissolve in conventional organic solvents such as chloroform, toluene, or tetrahydrofuran [21, 28, 32-36]. Their emission and absorption spectra are red-shifted relative to PPV itself, and the polymers fluorescence and electroluminescence quantum yields are greater than parent PPV. This benefit may be a consequence of the long alkyl chains isolating the polymer chains from each other. 

Although APDC complexes are soluble in many organic solvents, it is found that 4-methylpent-2-one (isobutyl methyl ketone) and heptan-2-one (n-pentyl methyl ketone) are, in general, the most satisfactory for direct nebulisation into the air/acetylene flame used in atomic absorption spectroscopy. 

Further techniques which may be applied directly to the solvent extract are flame spectrophotometry and atomic absorption spectrophotometry (AAS).13 The direct use of the solvent extract in AAS may be advantageous since the presence of the organic solvent generally enhances the sensitivity of the method. However, the two main reasons for including a chemical separation in the preparation of a sample for AAS are ... 

---