Of aniline salts

Compounds of this type are soon reconverted by adds into dia-zonium- and amine-salt. In the case of the diaryltriazenes this reconversion is already caused by a quite feebly acid reaction, e.g. that of aniline salts in the presence of excess of base but under these conditions the diazonium salt can combine with the amine present in excess to form an azo-dye (Rosenhauer). The equation... 

Of the various published methods of preparing phenylurea, such as treatment of aniline salts with potassium cyanate in water solution,1 heating aniline with urea,2 with cyanic acid,3 or with cyanogen chloride,4 and the interaction of phenyl isocyanate or phenylcarbamine chloride with ammonia,5 the only ones to be considered as practical methods for preparation are the first two. The first suffers from the disadvantage that potassium cyanate is not easily prepared in the laboratory and rapidly undergoes spontaneous decomposition in storage while by the action of urea on aniline alone, carbanilide is formed in rather larger proportion than phenylurea. 

The problems associated with the separation of phosphate esters are the tendency of the spots to diffuse difficulty of reproducing RF values variability of RF values with complexity of the mixture being resolved and distance of solvent travel proper purification and equilibration of the filter paper effect of inorganic ions in natural mixtures and the choice of suitable solvent mixtures for desired separations. The problem of detecting the separated spots is somewhat simpler. In addition to methods applicable to the detection of reducing sugars (e.g., use of aniline salts fructose esters are detected by naphthoresorcinol-acid), methods depending on phosphomolybdate formation are most commonly used. Hanes and Isher-... 

Commercial processes for obtaining the N-alkylated anilines are based on the reaction of aniline salts with alcohol in an autoclave at about 200°. A laboratory adaptation of this application of an alcohol as the alkylating... 

As a substituent on an aromatic ring, the amine salt group has an unusually uniform effect on the chemical shifts of the ortho, meta and para hydrogens. The series of aniline salts presented indicate the minimal effect that the type of acid involved, the solvent employed and the degree of amine substitution have on the chemical shift of the phenyl protons. The aromatic resonance for all of these aniline salts appears as a relatively sharp peak in the narrow chemical shift range from 7.50-7.55 ppm. 

Conversion of the salt of a weak base into the free base. Prepare a column of a strong base anion resin (such as Amberlite IRA-40o(OH) ) washed with distilled water as above. Drain off most of the water and then allow 100 ml. of A//2.Na.2C03 solution to pass through the column at 5 ml. per minute. Again wash the column with 200 ml. of distilled water. Dissolve 0-05 g. of aniline hydrochloride in 100 ml. of distilled water and pass the solution down the column. The effluent contains aniline in solution and free from all other ions. 

Diazonium salts couple readily with aromatic primary amines, giving diazoamino compounds. If for instance an aqueous solution of aniline sulphate is diazotised with a deficiency of nitrous acid, only part of it is converted into benzenediazonium sulphate and the latter then couples with the unchanged aniline to give diazoaminobenzene. The reaction is carried out at the opti-CeHsNHj.HjSO + HONO = CbHsNjHSO, + zHaO... 

The most noteworthy reaction of azo-compounds is their behaviour on reduction. Prolonged reduction first saturates the azo group, giving the hydrazo derivative (C NH-NH C), and then breaks the NH NH linkage, with the formation of two primary amine molecules. If method (1) has been employed to prepare the azo-compound, these two primary amines will therefore be respectively (a) the original amine from which the diazonium salt was prepared, and (6) the amino derivative of the amine or phenol with which the diazonium salt was coupled. For example, amino-azobenzene on complete reduction gives one equivalent of aniline, and one of p-phenylene diamine, NHaCeH NH benzene-azo-2-naphthoI similarly gives one equivalent of aniline and one of... 

The method can therefore be used to estimate the percentage of aniline hydrochloride in a crude sample, provided the impurities are not themselves salts of other similar amines. Alternatively, if aniline is known to be a monacidic base (forming therefore a mono-hydrochloride) the molecular weight of aniline can be determined, since the molecular weight of the aniline hydrochloride is clearly that weight which is neutralised by 1000 ml. of vl/.NaOH solution. 

Dilute hydrochloric or sulphuric acid finds application in the extraction of basic substances from mixtures or in the removal of basic impurities. The dilute acid converts the base e.g., ammonia, amines, etc.) into a water-soluble salt e.g., ammonium chloride, amine hydrochloride). Thus traces of aniline may be separated from impure acetanilide by shaking with dilute hydrochloric acid the aniline is converted into the soluble salt (aniline hydrochloride) whilst the acetanilide remains unaffected. 

Anilides. Dilute the acid chloride with 5 ml. of pure ether (or benzene), and add a solution of 2 g. of pure aniline in 15-20 ml. of the same solvent until the odour of the acid chloride has disappeared excess of aniline is not harmful. Shake with excess of dilute hydrochloric acid to remove aniline and its salts, wash the ethereal (or benzene) layer with 3-5 ml. of water, and evaporate the solvent [CAUTION ] Recrystallise the anilide from water, dilute alcohol or benzene - light petroleum (b.p. 60-80°). 

Place 1 0 g. of the monobasic acid and 2 g. of aniline or p-toluidine in a dry test-tube, attach a short air condenser and heat the mixture in an oil bath at 140-160° for 2 hours do not reflux too vigorously an acid that boils below this temperature range and only allow steam to escape from the top of the condenser. For a sodium salt, use the proportions of 1 g. of salt to 1 5 g. of the base. If the acid is dibasic, employ double the quantity of amine and a reaction temperature of 180-200° incidentally, the procedure is recommended for dibasic acids since the latter frequently give anhydrides with thionyl chloride. Powder the cold reaction mixture, triturate it with 20-30 ml. of 10 per cent, hydrochloric acid, and recrystallise from dilute alcohol. 

Dissolve 3-5 g. of aniline hydrochloride in 20 ml. of absolute ethyl alcohol contained in a 50 ml. conical flask, and add 0-5 ml. of a saturate solution of hydrogen chloride in absolute ethyl alcohol. Cool in ice and add 4 g. (4 -6 ml.) of iso-amyl nitrite (compare Section 111,53) gradually. Allow the mixture to stand for 5-10 minutes at the room temperature, and precipitate the diazonium salt by the gradual addition of ether. Filter ofiF the crystals at the pump on a small Buchner funnel, wash it with 5 ml. of alcohol - ether (1 1), and then with 10 ml. of ether. Keep... 

Attention has previously (see Diazonium Sails) been drawn to the fact that unless an excess of hydrochloric (or mineral) acid is used in the diazotisation process, coupling occurs between the diazonium salt and the amine to give diazoamino compounds. Thus phenyldiazonium chloride and aniline yield diazoaminobenzene. This substance may be conveniently prepared by dissolving two equivalents of aniline in three equivalents of hydrochloric acid, and adding one equivalent of sodium nitrite in aqueous solution followed by two equivalents of sodium acetate ... 

Into a 1-litre beaker, provided with a mechanical stirrer, place 36 - 8 g. (36 ml.) of aniline, 50 g. of sodium bicarbonate and 350 ml. of water cool to 12-15° by the addition of a little crushed ice. Stir the mixture, and introduce 85 g. of powdered, resublimed iodine in portions of 5-6 g, at intervals of 2-3 minutes so that all the iodine is added during 30 minutes. Continue stirring for 20-30 minutes, by which time the colour of the free iodine in the solution has practically disappeared and the reaction is complete. Filter the crude p-iodoaniline with suction on a Buchner funnel, drain as completely as possible, and dry it in the air. Save the filtrate for the recovery of the iodine (1). Place the crude product in a 750 ml. round-bottomed flask fitted with a reflux double surface condenser add 325 ml. of light petroleum, b.p. 60-80°, and heat in a water bath maintained at 75-80°. Shake the flask frequently and after about 15 minutes, slowly decant the clear hot solution into a beaker set in a freezing mixture of ice and salt, and stir constantly. The p-iodoaniline crystallises almost immediately in almost colourless needles filter and dry the crystals in the air. Return the filtrate to the flask for use in a second extraction as before (2). The yield of p-iodoaniline, m.p. 62-63°, is 60 g. 

Separations based upon differences in the chemical properties of the components. Thus a mixture of toluene and anihne may be separated by extraction with dilute hydrochloric acid the aniline passes into the aqueous layer in the form of the salt, anihne hydrochloride, and may be recovered by neutralisation. Similarly, a mixture of phenol and toluene may be separated by treatment with dilute sodium hydroxide. The above examples are, of comse, simple apphcations of the fact that the various components fah into different solubihty groups (compare Section XI,5). Another example is the separation of a mixture of di-n-butyl ether and chlorobenzene concentrated sulphuric acid dissolves only the w-butyl other and it may be recovered from solution by dilution with water. With some classes of compounds, e.g., unsaturated compounds, concentrated sulphuric acid leads to polymerisation, sulphona-tion, etc., so that the original component cannot be recovered unchanged this solvent, therefore, possesses hmited apphcation. Phenols may be separated from acids (for example, o-cresol from benzoic acid) by a dilute solution of sodium bicarbonate the weakly acidic phenols (and also enols) are not converted into salts by this reagent and may be removed by ether extraction or by other means the acids pass into solution as the sodium salts and may be recovered after acidification. Aldehydes, e.g., benzaldehyde, may be separated from liquid hydrocarbons and other neutral, water-insoluble hquid compounds by shaking with a solution of sodium bisulphite the aldehyde forms a sohd bisulphite compound, which may be filtered off and decomposed with dilute acid or with sodium bicarbonate solution in order to recover the aldehyde. 

The diazonium salts 145 are another source of arylpalladium com-plexes[114]. They are the most reactive source of arylpalladium species and the reaction can be carried out at room temperature. In addition, they can be used for alkene insertion in the absence of a phosphine ligand using Pd2(dba)3 as a catalyst. This reaction consists of the indirect substitution reaction of an aromatic nitro group with an alkene. The use of diazonium salts is more convenient and synthetically useful than the use of aryl halides, because many aryl halides are prepared from diazonium salts. Diazotization of the aniline derivative 146 in aqueous solution and subsequent insertion of acrylate catalyzed by Pd(OAc)2 by the addition of MeOH are carried out as a one-pot reaction, affording the cinnamate 147 in good yield[115]. The A-nitroso-jV-arylacetamide 148 is prepared from acetanilides and used as another precursor of arylpalladium intermediate. It is more reactive than aryl iodides and bromides and reacts with alkenes at 40 °C without addition of a phosphine ligandfl 16]. 

Yields can be very good Beyer (402) reports a 90% yield when coupling 2-amino-4-phenylthiazole with the diazonium salt of aniline. The coupling of diazotized anilines under modified conditions has been reported in a work treating the preparation of antineoplastics (403). 

Mixing of quaternary salt, aniline, and ethylorthoformate (method B. Scheme 33). 

Textile dyes were, until the nineteenth century invention of aniline dyes, derived from biological sources plants or animals, eg, insects or, as in the case of the highly prized classical dyestuff Tyrian purple, a shellfish. Some of these natural dyes are so-caUed vat dyes, eg, indigo and Tyrian purple, in which a chemical modification after binding to the fiber results in the intended color. Some others are direct dyes, eg, walnut sheU and safflower, that can be apphed directly to the fiber. The majority, however, are mordant dyes a metal salt precipitated onto the fiber facUitates the binding of the dyestuff Aluminum, iron, and tin salts ate the most common historical mordants. The color of the dyed textile depends on the mordant used for example, cochineal is crimson when mordanted with aluminum, purple with iron, and scarlet with tin (see Dyes AND DYE INTERMEDIATES). 

Aromatic amines form addition compounds and complexes with many inorganic substances, such as ziac chloride, copper chloride, uranium tetrachloride, or boron trifluoride. Various metals react with the amino group to form metal anilides and hydrochloric, sulfuric, or phosphoric acid salts of aniline are important intermediates in the dye industry. 

Basic Orange 1 (130) (aniline coupled to 2,4-diamiaotoluene) and Basic Orange 2 (22) (aniline coupled to y -phenylenediamiae) are examples of amine salt type cationic azo dyes. The cation is formed by protonation under acidic conditions. Under neutral or alkaline conditions, these dyes behave more like disperse dyes. In 1988 the U.S. production of Cl Basic Orange 2 amounted to 132 tons. 

In a 500-cc. round-bottom flask (Note i) fitted with a mechanical stirrer and surrounded by an ice-salt cooling bath, are placed 54 g. (0.71 mole) of carbon disulfide and 90 cc. (1.3 moles) of concentrated ammonium hydroxide (sp. g. 0.9). The stirrer is started and 56 g. (0.6 mole) of aniline (Note 2) is run into the mixture from a separatory funnel at such a rate that the addition is complete in about twenty minutes. The stirring is continued for thirty minutes after all of the aniline has been added, and then the reaction mixture is allowed to stand for another, thirty minutes. During this time a heavy precipitate of ammonium phenyl dithiocarbamate separates and may even stop the stirrer. 

Aniline [62-53-3] M 93.1, f -6.0", b 68.3/lOmm, 184.4"/760mm, d 1.0220, n 1.585, n s 1.5832, pK 4.60. Aniline is hygroscopic. It can be dried with KOH or CaH2, and distd at reduced pressure. Treatment with stannous chloride removes sulfur-containing impurities, reducing the tendency to become coloured by aerial oxidn. Can be crystd from Et20 at low temps. More extensive purifications involve preparation of derivatives, such as the double salt of aniline hydrochloride and cuprous chloride or zinc chloride, or A -acetylaniline (m 114") which can be recrystd from water. 

N-2-cyanoethylaniline has been prepared (accompanied by much of the N,N -bis-2-cyanoethyl compound) by heating aniline, acrylonitrile and acetic acid either in an autoclave, or at refluxing temperature for 10 hours in the presence of various inorganic catalysts. The substance has also been obtained, free of the N,N -bis-2-cyanoethyl compound, from aniline salts and /3-diethylaminopropionitrile. ... 

Combined Erythrina Alkaloids. The sources of the liberated alkaloids (see above) are now known to be, at least in two cases, the sulphur-containing alkaloids erysothiopine and erysothiovine, which are esters of sulphoacetic acid, HOOC. CHj. SOj. OH, identified as the aniline salt, m.p. 187-9° with erj sopine and erysovine respectively. The sources of erysodine and erysonine have not yet been isolated. These combined alkaloids arc believed to be sulphonic esters, of the type HO. OC. CHj. SOj. 0. R, where R is the alkaloidal residue. ... 

The second point is somewhat less obvious but is readily illustrated by the synthesis of 1,3,5-tribromobenzene. This particular- substitution pattern cannot be obtained by direct brornination of benzene because bromine is an ortho, para director. Instead, advantage is taken of the powerful activating and ortho, para-directing effects of the fflnino group in aniline. Brornination of aniline yields 2,4,6-tribromoaniline in quantitative yield. Diazotization of the resulting 2,4,6-tribromoaniline and reduction of the diazonium salt gives the desired 1,3,5-tribromobenzene. 

Reaction.—Make a solution of 4 grams stannous chloride in TO c.c. cone, hydrochloric acid, add 2 grams aminoazobenzene, and boil for a few minutes. On cooling ciystals of the hydrochlorides of aniline and yi-phenylenediamine separate out. The liquid is filtered and washed with a little cone, hydrochloric acid to remove the tin salts. If the precipitate is dissolved in water and made alkaline with caustic soda, a mixture of liquid aniline and solid/-phenylenediamine is precipitated, from which the former may be removed by filtering, washing, and draining on a porous plate. 

Rosaniline or magenta was originally obtained by oxidising with arsenic acid a mixture of aniline with 0- and />-toluidine. The product was then lixiviated and treated with common salt, which converted the ai senate into the hydrochloride of rosaniline. Pararosaniline was prepared in a similar way fiom a niixtuie of aniline and /-toluidine. The series... 

---