Range, normal

Substances in this category include Krypton, sodium chloride, and diamond, as examples, and it is not surprising that differences in detail as to frictional behavior do occur. The softer solids tend to obey Amontons law with /i values in the normal range of 0.5-1.0, provided they are not too near their melting points. Ionic crystals, such as sodium chloride, tend to show irreversible surface damage, in the form of cracks, owing to their brittleness, but still tend to obey Amontons law. This suggests that the area of contact is mainly determined by plastic flow rather than by elastic deformation. 

A number of friction studies have been carried out on organic polymers in recent years. Coefficients of friction are for the most part in the normal range, with values about as expected from Eq. XII-5. The detailed results show some serious complications, however. First, n is very dependent on load, as illustrated in Fig. XlI-5, for a copolymer of hexafluoroethylene and hexafluoropropylene [31], and evidently the area of contact is determined more by elastic than by plastic deformation. The difference between static and kinetic coefficients of friction was attributed to transfer of an oriented film of polymer to the steel rider during sliding and to low adhesion between this film and the polymer surface. Tetrafluoroethylene (Telfon) has a low coefficient of friction, around 0.1, and in a detailed study, this lower coefficient and other differences were attributed to the rather smooth molecular profile of the Teflon molecule [32]. 

Pituitary Dwarfism. Pituitary dwarfism is a condition characterized by an inabiHty to produce or secrete normal levels of endogenous hGH. The condition results in reduced heights of individuals afflicted with the condition and has been treated by intramuscular or subcutaneous injection of hGH. Pituitary hGH was used prior to the approval of biosynthetic hGH. If treatment is initiated early enough, the patient can attain a final adult height weU within the normal range. 

It is difficult to define the normal range of iodine intake in humans, and despite efforts to provide iodine supplementation in many geographic areas of the world, endemic iodine deficiency and attendant goiter remain a world health problem (147). Exposure to excess iodine may sometimes lead to the development of thyroid disease. This unusual type of iodide-induced goiter has been found, for example, in 10% of the population of a Japanese island where fishermen and their families consume large quantities of an iodine-rich seaweed and have an iodine intake as high as 200 mg/d (148). 

Item Influencing. a operations Normal range Specifications ... 

For waterproofing, sodium silicate concentrations below 30% are adequate concentrations between 35 and 70% are used for strength improvement. Grouts having 35 vol % or higher silicate resist deterioration on freeze—thaw or wet—dry cycles. Water permeability of sands can be reduced from 10 to 10 cm/s. Unconfined compressive strengths of stabilized sand can vary from 103 to 4130 kPa (15—600 psi) the normal range is between 690 and 1380 kPa. 

Normal ranges of manganese, siUcon, phosphoms, and sulfur are assumed (see Steel). The balance is Fe in all cases. 

Although it is being found that vitamin D metaboUtes play a role ia many different biological functions, metaboHsm primarily occurs to maintain the calcium homeostasis of the body. When calcium semm levels fall below the normal range, 1 a,25-dihydroxy-vitainin is made when calcium levels are at or above this level, 24,25-dihydroxycholecalciferol is made, and 1 a-hydroxylase activity is discontiaued. The calcium homeostasis mechanism iavolves a hypocalcemic stimulus, which iaduces the secretion of parathyroid hormone. This causes phosphate diuresis ia the kidney, which stimulates the 1 a-hydroxylase activity and causes the hydroxylation of 25-hydroxy-vitamin D to 1 a,25-dihydroxycholecalciferol. Parathyroid hormone and 1,25-dihydroxycholecalciferol act at the bone site cooperatively to stimulate calcium mobilization from the bone (see Hormones). Calcium blood levels are also iafluenced by the effects of the metaboUte on intestinal absorption and renal resorption. 

A more simplified description is a unit that combusts materials in the presence of oxygen at temperatures normally ranging from 800 to 1650°C. A typical configuration of an incinerator is shown in Figure 9. Typical types of incineration units that are discussed herein are catalytic oxidation, fluidized beds, hquid injection, multiple hearth furnaces, and rotary kiln. Thermal desorption is also discussed. However, an overview of the main factors affecting incinerator performance is presented first, below. 

Zinc is an essential element and thus can exist in both the deficient or toxic state in plants and animals. Deficiency occurs in some plants when the tissue content drops below 20 ppm. The normal range is 25—150 ppm. The toxic effect of zinc has been seen at 400 ppm, although plants vary widely in their tolerance. 

In most other reactions the azolecarboxylic acids and their derivatives behave as expected (cf. Scheme 52) (37CB2309), although some acid chlorides can be obtained only as hydrochlorides. Thus imidazolecarboxylic acids show the normal reactions they can be converted into hydrazides, acid halides, amides and esters, and reduced by lithium aluminum hydride to alcohols (70AHC(12)103). Again, thiazole- and isothiazole-carboxylic acid derivatives show the normal range of reactions. 

Diffusion within the largest cavities of a porous medium is assumed to be similar to ordinary or bulk diffusion except that it is hindered by the pore walls (see Eq. 5-236). The tortuosity T that expresses this hindrance has been estimated from geometric arguments. Unfortunately, measured values are often an order of magnitude greater than those estimates. Thus, the effective diffusivity D f (and hence t) is normally determined by comparing a diffusion model to experimental measurements. The normal range of tortuosities for sihca gel, alumina, and other porous solids is 2 < T < 6, but for activated carbon, 5 < T < 65. 

FIG. 10-26 Pump coverage chart based on normal ranges of operation of commercially available types. Solid lines use left ordinate, bead scale. Broken lines use right ordinate, pressure scale. To conveii gallons per minute to cubic meters per hour, multiply by 0.2271 to conveii feet to meters, multiply by 0.3048 and to conveii poiinds-force per square inch to Idlopascals, multiply by 6.895. 

Cycles of concentration involved with cooling-tower operation normally range from three to five cycles. Below three cycles of concentration, excessive blowdown quantities are required and the addition of acid to limit scale formation should be considered. 

Data for determining the size of natural-draft towers have been presented by Chilton [Proc. Inst. Elec. Eng., 99,440 (1952)] and Rish and Steel (ASCE Swuposium on Thermal Power Plants, October 19.58). Chilton showed that the duty coefficient Df of a tower is approximately constant over its normal range of operation and is related to tower size by an efficiency factor or performance coefficient as follows ... 

A major difficulty which has been encountered with these definitions (identified as a particular problem by EDSTAC) is the definition of the term adverse . For a chemical to be judged an ED, it is important to show that the response seen has an adverse effect on the health or reproductive capacity of affected organisms or populations and is not just a change which falls within the normal range of physiological variation. 

However, when an expander has to operate at mismatehed eondi-tions, the aetual mismateh usually oeeurs in the inlet butterfly valve, whieh attempts to maintain regenerator pressure. Fortunately, proeessing parameters ean also be modulated under different produetion eapaeities. In sueh eireumstanees, it is important to keep the volume flow in the normal range to maintain system effieieney. For an ideal gas, the eonditional equation is ... 

The two bold lines at = 1 and = 1.7 represent the normal range of tolerance capability for the process under ideal material and component geometry conditions. This information can be used as knowledge in the redesign process if required. 

The greater the molecular weight the higher is the flow temperature and the heat distortion temperature. Variations in molecular weight, in the normal range, however, have less effect than do variations in the degree of acetylation and in the plasticiser used. 

The reasons AES is a surface-specific technique have been given in Sect. 2.1.1, with reference to Fig. 2.2. The normal range of kinetic energies recorded in an AES spectrum would typically be from 20 to 1000 eV, corresponding to inelastic mean free path values of 2 to 6 monolayers. 

---