Methyl methacrylate solvents

Solvents 1 and 2 are known to be good solvents for poly(methyl methacrylate) solvent 3 readily dissolves polystyrene.The solubility tests show that the radically polymerized sample is insoluble in all three solvents.The solubility isthusdifferentfrom that of both poly(methyl methacrylate) and polystyrene.The anionically polymerized product dissolves on warming in the acetone/methanol mixture and also in acetonitrile it is insoluble in cyclohexane/toluene.The solubility is thus similar to that of poly(methyl methacrylate). For the cationically initiated polymerization the product is only slightly soluble in acetone/methanol, insoluble in acetonitrile, but very readily soluble in cyclohexane/toluene.The solubility thus resembles that of polystyrene. 

Acetone is used for the production of methyl methacrylate, solvents, bisphenol A, aldol chemicals, and pharmaceuticals. 

Bristow, G. M., "Phase Separation in Rubber-Poly(methyl methacrylate)-Solvent Systems," J. Appl. Polym. Sci., 2, 120 (1959). 

Figure 6-20. Dependence of the (03)e values on the average mass fraction wmma of the methylmethacrylate monomeric units in poly(styrene-co-methyl methacrylates). Solvent methyl-isopropyl ketone precipitant n-hexane temperature 25 C (after H.-G. Elias and U. Gruber).

MODAR Modified acrylic liquid resins have been available since the mid 80s and are used in closed mould and pultrusion technologies. When combined with ATH they offer low smoke low toxicity fire performance in composites. These resins are more accurately described as oligourethane-methacrylates dissolved in methyl methacrylate solvent monomer . Crosslinking, through the methacrylate functionality on the backbone and the solvent is initiated in the same way as for unsaturated polyester resin by decomposing an organic peroxide, either thermally or chemically with an accelerator. 

Methyl Methacrylate Solvents Glutaraldehyde Ethylene Oxide... 

At 25°C, the Mark-Houwink exponent for poly(methyl methacrylate) has the value 0.69 in acetone and 0.83 in chloroform. Calculate (retaining more significant figures than strictly warranted) the value of that would be obtained for a sample with the following molecular weight distribution if the sample were studied by viscometry in each of these solvents ... 

Bhatnagar and Biswast measured the turbidity at 436 nm of 2l single sample of poly(methyl methacrylate) in several solvents, including acetone and methyl ethyl ketone (MEK) ... 

Most of the polymer s characteristics stem from its molecular stmcture, which like POE, promotes solubiUty in a variety of solvents in addition to water. It exhibits Newtonian rheology and is mechanically stable relative to other thermoplastics. It also forms miscible blends with a variety of other polymers. The water solubiUty and hot meltable characteristics promote adhesion in a number of appHcations. PEOX has been observed to promote adhesion comparable with PVP and PVA on aluminum foil, cellophane, nylon, poly(methyl methacrylate), and poly(ethylene terephthalate), and in composite systems improved tensile strength and Izod impact properties have been noted. 

A solubihty parameter of 24.5-24.7 MPa / [12.0-12.1 (cal/cm ) ] has been calculated for PVF using room temperature swelling data (69). The polymer lost solvent to evaporation more rapidly than free solvent alone when exposed to air. This was ascribed to reestabUshment of favorable dipole—dipole interactions within the polymer. Infrared spectral shifts for poly(methyl methacrylate) in PVF have been interpreted as evidence of favorable acid—base interactions involving the H from CHF units (70). This is consistent with the greater absorption of pyridine than methyl acetate despite a closer solubihty parameter match with methyl acetate. 

Methyl Isobutyl Ketone. Methyl isobutyl ketone (MIBK) (4-methyl-2-pentanone), (CH2)2CHCH2COCH2, is an industrially important solvent which after methyl methacrylate and bisphenol A is the third largest tonnage product obtained from acetone. 

Chain transfer to solvent is an important factor in controlling the molecular weight of polymers prepared by this method. The chain-transfer constants for poly(methyl methacrylate) in various common solvents (C) and for various chain-transfer agents are Hsted in Table 10. 

Process Raw Material. Industrial solvents are raw materials in some production processes. Eor example, only a small proportion of acetone is used as a solvent, most is used in producing methyl methacrylate and bisphenol A. Alcohols are used in the manufacture of esters and glycol ethers. Diethylenetriamine is also used in the manufacture of curing agents for epoxy resins. Traditionally, chlorinated hydrocarbon solvents have been the starting materials for duorinated hydrocarbon production. 

Polymerization and Spinning Solvent. Dimethyl sulfoxide is used as a solvent for the polymerization of acrylonitrile and other vinyl monomers, eg, methyl methacrylate and styrene (82,83). The low incidence of transfer from the growing chain to DMSO leads to high molecular weights. Copolymerization reactions of acrylonitrile with other vinyl monomers are also mn in DMSO. Monomer mixtures of acrylonitrile, styrene, vinyUdene chloride, methallylsulfonic acid, styrenesulfonic acid, etc, are polymerized in DMSO—water (84). In some cases, the fibers are spun from the reaction solutions into DMSO—water baths. 

Block copolymers of vinyl acetate with methyl methacrylate, acryflc acid, acrylonitrile, and vinyl pyrrohdinone have been prepared by copolymeriza tion in viscous conditions, with solvents that are poor solvents for the vinyl acetate macroradical (123). Similarly, the copolymeriza tion of vinyl acetate with methyl methacrylate is enhanced by the solvents acetonitrile and acetone and is decreased by propanol (124). Copolymers of vinyl acetate containing cycHc functional groups in the polymer chain have been prepared by copolymeriza tion of vinyl acetate with A/,A/-diaIlylcyanamide and W,W-diaIl5lamine (125,126). 

In general, the azo colors are useful for coloring polystyrene, phenoHcs, and rigid poly(vinyl chloride). Many are compatible with poly(methyl methacrylate), but in this case the weatherabiUty of the resin far exceeds the life of the dyes. Among the more widely used azo dyes (qv) are Solvent Yellows 14 and 72 Orange 7 and Reds 1, 24, and 26. 

The anthraquinones are useful in acrylics and are compatible with polystyrene and ceUulosics. Solvent Red 111 has a special affinity for poly(methyl methacrylate) as the red in automobile taillights exposure for a year in Florida or Arizona produces only a very slight darkening. Acid types are usehil for phenohcs (see Dyes, anthraquinone). 

The acetone supply is strongly influenced by the production of phenol, and so the small difference between total demand and the acetone suppHed by the cumene oxidation process is made up from other sources. The largest use for acetone is in solvents although increasing amounts ate used to make bisphenol A [80-05-7] and methyl methacrylate [80-62-6]. a-Methylstyrene [98-83-9] is produced in controlled quantities from the cleavage of cumene hydroperoxide, or it can be made directly by the dehydrogenation of cumene. About 2% of the cumene produced in 1987 went to a-methylstyrene manufacture for use in poly (a-methylstyrene) and as an ingredient that imparts heat-resistant quaUties to polystyrene plastics. 

Cyanohydrins are used primarily as intermediates in the production of other chemicals. Manufacture of methyl methacrylate, used to make acrylic mol ding resins and clear sheet, eg, Plexiglas acrylic sheet, from acetone cyanohydrin is the most economically important cyanohydrin process (see Methacrylic polymers). Cyanohydrins are also used as solvents in appHcations including fiber-spinning and metals refining. Cyanohydrins and derivatives reportedly act as antiknock agents in fuel oil and motor fuels and serve as electrolytes in electrolytic capacitors. 

The auto-acceleration effect appears most marked with polymers that are insoluble in their monomers. In these circumstances the radical end becomes entrapped in the polymer and termination reactions become very difficult. It has been suggested that, in thermodynamic terms, methyl methacrylate is a relatively poor solvent for poly(methyl methacrylate) because it causes radicals to coil while in solution. The termination reaction is then determined by the rate at which the radical ends come to the surface of the coil and hence become available for mutual termination. 

The solubility of commercial poly(methyl methacrylate) is consistent with that expected of an amorphous thermoplastic with a solubility parameter of about 18.8 MPa. Solvents include ethyl acetate (8 = 18.6), ethylene dichloride (8 = 20.0), trichloroethylene (8 = 19), chloroform (8 = 19) and toluene (8 = 20), all in units ofMPa. Difficulties may, however, occur in dissolving cast poly(methyl methacrylate) sheet because of its high molecular weight. 

As may be expected of an amorphous polymer in the middle range of the solubility parameter table, poly(methyl methacrylate) is soluble in a number of solvents with similar solubility parameters. Some examples were given in the previous section. The polymer is attacked by mineral acids but is resistant to alkalis, water and most aqueous inorganic salt solutions. A number of organic materials although not solvents may cause crazing and cracking, e.g. aliphatic alcohols. 

There are probably several factors which contribute to determining the endo exo ratio in any specific case. These include steric effects, dipole-dipole interactions, and London dispersion forces. MO interpretations emphasize secondary orbital interactions between the It orbitals on the dienophile substituent(s) and the developing 7t bond between C-2 and C-3 of the diene. There are quite a few exceptions to the Alder rule, and in most cases the preference for the endo isomer is relatively modest. For example, whereas cyclopentadiene reacts with methyl acrylate in decalin solution to give mainly the endo adduct (75%), the ratio is solvent-sensitive and ranges up to 90% endo in methanol. When a methyl substituent is added to the dienophile (methyl methacrylate), the exo product predominates. ... 

Monodispersed poly (methyl methacrylate-ethyleneglycol dimethacrylate) is prepared by a multistep swelling and polymerization method. When a good solvent such as toluene is applied as a porogen, the seed polymer severely affects the pore structure, whereas no effects are observed with poor solvents, such as cyclohexanol, as a porogen, in comparison with the conventional suspension polymerization (68,69). 

---