Methyl methacrylate analysis

Fox and Schneckof carried out the free-radical polymerization of methyl methacrylate between -40 and 250 C. By analysis of the a-methyl peaks in the NMR spectra of the products, they determined the following values of a, the probability of an isotactic placement in the products prepared at the different temperatures ... 

The dynamic mechanical properties of VDC—VC copolymers have been studied in detail. The incorporation of VC units in the polymer results in a drop in dynamic modulus because of the reduction in crystallinity. However, the glass-transition temperature is raised therefore, the softening effect observed at room temperature is accompanied by increased brittleness at lower temperatures. These copolymers are normally plasticized in order to avoid this. Small amounts of plasticizer (2—10 wt %) depress T significantly without loss of strength at room temperature. At higher levels of VC, the T of the copolymer is above room temperature and the modulus rises again. A minimum in modulus or maximum in softness is usually observed in copolymers in which T is above room temperature. A thermomechanical analysis of VDC—AN (acrylonitrile) and VDC—MMA (methyl methacrylate) copolymer systems shows a minimum in softening point at 79.4 and 68.1 mol % VDC, respectively (86). 

Polyacrylates are an industrially important class of polymers. The name polyacrylate is variously used to refer to polymers of acrylate esters [e.g., poly(methyl methacrylate)] as well as polymers of acrylic acids [e.g., poly(meth-acrylic acid)]. Because the former is organic soluble while the latter is not, chromatographic analysis of these two requires quite different conditions. This chapter discusses both types of polymers, separating their consideration when necessary. We will refer to both types of polymers as polyacrylates, letting the context indicate whether we are referring to an ester or to an acid polymer. 

Kondo maintained his interest in this area, and with his collaborators [62] he recently made detailed investigations on the polymerization and preparation of methyl-4-vinylphenyl-sulfonium bis-(methoxycarbonyl) meth-ylide (Scheme 27) as a new kind of stable vinyl monomer containing the sulfonium ylide structure. It was prepared by heating a solution of 4-methylthiostyrene, dimethyl-diazomalonate, and /-butyl catechol in chlorobenzene at 90°C for 10 h in the presence of anhydride cupric sulfate, and Scheme 27 was polymerized by using a, a -azobisi-sobutyronitrile (AIBN) as the initiator and dimethylsulf-oxide as the solvent at 60°C. The structure of the polymer was confirmed by IR and NMR spectra and elemental analysis. In addition, this monomeric ylide was copolymerized with vinyl monomers such as methyl methacrylate (MMA) and styrene. 

Trauzl Test. 21,.4% of TNT when pure (Ref 26) for mixts see below Uses. It does not gelatinize NC (Ref 15). It improves the octane rating of diesel fuels (Ref 26). It decreases the polymerization rate of methyl methacrylate (Ref 24), and styrene (Ref 23), but. does not inhibit the reaction. A review of its use as an oxidizer in rocket propints is given in Ref 33. TeNMe gives yellow to orange colors with olefins and aromatic compds. This is used as a diagnostic test for the presence of these groups in org analysis (Refs 6, 9, 16, 17 29)... 

TECHNO-ECONOMIC ANALYSIS OF THE PYROLYSIS OF POLY(METHYL METHACRYLATE)... 

The purpose of the study was to determine the optimum conditions of operation of pyrolysis equipment by the combined solution of equations relating to the technological and economic analysis of the process. The material considered was poly(methyl methacrylate) one of the most popular types of plastic waste. Articles from this journal can be requested for translation by subscribers to the Rapra produced International Polymer Science and Technology. 

The presence of two hydroxyl groups per molecule in poly-(methyl methacrylate) and in polystyrene, each polymerized in aqueous media using the hydrogen peroxide-ferrous ion initiation system, has been established " by chemical analysis and determination of the average molecular weight. Poly-(methyl methacrylate) polymerized by azo-bis-isobutyronitrile labeled with radioactive has been shown to... 

As the majority of stabilisers has the structure of aromatics, which are UV-active and show a distinct UV spectrum, UV spectrophotometry is a very efficient analytical method for qualitative and quantitative analysis of stabilisers and similar substances in polymers. For UV absorbers, UV detection (before and after chromatographic separation) is an appropriate analytical tool. Haslam et al. [30] have used UV spectroscopy for the quantitative determination of UVAs (methyl salicylate, phenyl salicylate, DHB, stilbene and resorcinol monobenzoate) and plasticisers (DBP) in PMMA and methyl methacrylate-ethyl acrylate copolymers. From the intensity ratio... 

F.C. Y.Wang and P.B. Smith, Quantitative analysis and structure determination of styrene/ methyl methacrylate copolymers by pyrolysis gas chromatography, Anal. Chem., 68, 3033 3037(1996). 

Reaction of K3Co(CN) with PMMA. A 1.0 g sample of PMMA and 1.0g of the cobalt compound were combined in a standard vessel and pyrolyzed for 2 hrs at 375°C. The tube was removed from the oven and the contents of the tube were observed to be solid (PMMA is liquid at this temperature). The tube was reattached to the vacuum line via the break-seal and opened. Gases were determined by pressure-volume-temperature measurements on the vacuum line and identified by infrared spectroscopy. Recovered were 0.22g of methyl methacrylate and 0.11 g of CO and C02. The tube was then removed from the vacuum line and acetone was added. Filtration gave two fractions, 1.27g of acetone insoluble material and 0.30g of acetone soluble (some soluble material is always lost in the recovery process). The acetone insoluble fraction was then slurried with water, 0.11 g of material was insoluble in water. Infrared analysis of this insoluble material show both C-H and C-0 vibrations and are classified as char based upon infrared spectroscopy. Reactions were also performed at lower temperature, even at 260°C some char is evident in the insoluble fraction. 

TiCU readily functionalizes hydrophilic polymers such as poly(vinyl alcohol), m-ciesol novolac and methacrylic acid copolymers as well as moderately hydrophobic polymers such as poly(methyl methacrylate), poly(vinyl acetate), poly(benzyl methacrylate) and fully acetylated m-cresol novolac. HCI4 did not react with poly(styrene) to form etch resistant films indicating that very hydrophobic films follow a different reaction pathway. RBS analysis revealed that Ti is present only on the surface of hydrophilic and moderately hydrophobic polymer films, whereas it was found diffused through the entire thickness of the poly(styrene) films. The reaction pathways of hydrophilic and hydrophobic polymers with HCI4 are different because TiCl is hydrolysed by the surface water at the hydrophilic polymer surfaces to form an etch resistant T1O2 layer. Lack of such surface water in hydrophobic polymers explains the absence of a surface TiC>2 layer and the poor etching selectivities. 

For example, poly(methyl methacrylate) exposed to high energy or uv radiation gives a nine line ESR spectrum, as depicted in Figure 7. Analysis of this spectrum has indicated that the likely structure of the free radical responsible is (12) ... 

Velasco-Santos C, Marty nez-Hema ndez AL, Fisher FT, Ruotf R, Castanlo VM (2003a). Dynamical mechanical and thermal analysis of carbon nanotube-methyl methacrylate nanocomposites. J. Phys. D-Applied Phys. 36 1423-1428. 

In the following pages we shall treat, in detail, the NMR analysis of two polymers, poly(methyl methacrylate) and polypropylene, which have epitomized, in consecutive epochs, the most classical and fhiitful examples of interaction between NMR spectroscopy and macromolecular stereochemistry. 

The same type of addition—as shown by X-ray analysis—occurs in the cationic polymerization of alkenyl ethers R—CH=CH—OR and of 8-chlorovinyl ethers (395). However, NMR analysis showed the presence of some configurational disorder (396). The stereochemistry of acrylate polymerization, determined by the use of deuterated monomers, was found to be strongly dependent on the reaction environment and, in particular, on the solvation of the growing-chain-catalyst system at both the a and jS carbon atoms (390, 397-399). Non-solvated contact ion pairs such as those existing in the presence of lithium catalysts in toluene at low temperature, are responsible for the formation of threo isotactic sequences from cis monomers and, therefore, involve a trans addition in contrast, solvent separated ion pairs (fluorenyllithium in THF) give rise to a predominantly syndiotactic polymer. Finally, in mixed ether-hydrocarbon solvents where there are probably peripherally solvated ion pairs, a predominantly isotactic polymer with nonconstant stereochemistry in the jS position is obtained. It seems evident fiom this complexity of situations that the micro-tacticity of anionic poly(methyl methacrylate) cannot be interpreted by a simple Bernoulli distribution, as has already been discussed in Sect. III-A. 

Analysis of the poly(methyl methacrylate) sequences obtained by anionic polymerization was undertaken at the tetrad level in terms of two different schemes (10) one, a second-order Markov distribution (with four independent conditional probabilities, Pmmr Pmrr, Pmr Prrr) (44), the other, a two-state mechanism proposed by Coleman and Fox (122). In this latter scheme one supposes that the chain end may exist in two (or more) different states, depending on the different solvation of the ion pair, each state exerting a specific stereochemical control. A dynamic equilibrium exists between the different states so that the growing chain shows the effects of one or the other mechanism in successive segments. The deviation of the experimental data from the distribution calculated using either model is, however, very small, below experimental error, and, therefore, it is not possible to make a choice between the two models on the basis of statistical criteria only. 

The copolymers obtained for the P(DMA)-itat-(HPA) (Scheme 9) library revealed relatively low PDI values below 1.3 and increasing Mn,opc values with increasing HPA content, as listed in Tables. It should be noted that a poly(methyl methacrylate) (PMMA) calibration was used for the calculation of the Mn pc values and this causes an overestimation for HPA containing polymers. The copolymer compositions were calculated from the H NMR spectra however, this method was not suitable for reliable conversion determination since the DMA-C//3 groups overlap in the NMR spectra not only with the HPA-O// group but also with broad backbone signals, which obstruct any reliable integration. Therefore, elemental analysis was used as an alternative method for the calculation of the molecular composition of the copolymers. 

---