Methyl acrylate, reactions

In addition, the activation enthalpy and entropy for the cyclopentadiene and methyl acrylate reaction is 10.2 and -40.9 cal/mol K, respectively, in a methanol/water mixture [81], Therefore, analogous to the cyclopentadiene and methyl acrylate reaction, the butadiene and acrolein activation enthalpy (adjusted by 0.7 kcal/mol)... 

In a synthesis of the tricychc skeleton of FR901483 (45), Bonjoch and Sole reported a TMG (3) promoted conjugate addition reaction of nitroalkane to methyl acrylate. Reaction of methyl acrylate (40) and nitro acetal 41 [9,10], obtained from Diels-Alder reaction between nitroethylene and 2-(trimethylsilyloxy)-l,3-butadiene, gave nitro ester 42 in 71% yield. The ester 42 was further converted to the spiro compound 43, and a palladium promoted cyclization reaction led to the azatricyclic skeleton 44 (Scheme 7.7). 

The parallel can be extended. Vinyl carbenes are powerful dienophiles in Diels-Alder reactions, better than the corresponding esters or amides (Scheme 8.6). For the reaction between methyl acrylate and isoprene, compared to the reaction between vinyl carbene 8.20 and isoprene, the rate enhancement is about 2 x 10 in comparison, a rate enhancement of 7 x 10 is obtained by adding AICI3 to the methyl acrylate reaction. They are also excellent Michael acceptors (Scheme 8.7). The alkynyl carbenes are also very good in both regards. ... 

Bipyridyl(diethyl)platinum(ii) reacts with methyl acrylate with release of ethylene and formation of [Pt CH(Me)C02Me 2(bipy)]. No ethane was detected in the products and ethyl radicals are considered unlikely intermediates in the reaction. This contrasts with earlier studies of [Pt(R)2(L)2] complexes which react with diethyl fumarate to give [Pt(CHC02Et)a(L)J with release of alkyl radicals which could be trapped by Bu NO. Second-order kinetics were followed in the methyl acrylate reaction and if the stationary-state approximation is made for the intermediate [Pt(Et)2(CH2=CHCOaMe)] (19) in Scheme 10 the rate expression is... 

In more recent work, Ikushima et al. (279) applied the solubility parameter concept to the isoprene and methyl acrylate reaction to evaluate the solvent properties of SCCO2 as well as the mutual affinity among the various chemical species present in the reaction mixture. They estimated the pressure dependence of the solubility parameter of the activated complex through transition state theory at 50°C over the pressure range of 70-200 bar to study the nature of the complex and the effect of the solvent on the reaction. They observed that the solubility parameter of the activated complex approaches that of the reactants as the pressure approaches the critical point. This suggests that the nature of the activated complex becomes more similar to that of the reactants, hence the energy needed for formation of the complex becomes smaller near the critical point. That is, the reaction rate for formation of the complex is enhanced in the vicinity of the critical point, thus driving the overall reaction to the product. 

The Diels-Alder reaction provides us with a tool to probe its local reaction environment in the form of its endo-exo product ratio. Actually, even a solvent polarity parameter has been based on endo-exo ratios of Diels-Alder reactions of methyl acrylate with cyclopentadiene (see also section 1.2.3). Analogously we have determined the endo-exo ratio of the reaction between 5.1c and 5.2 in surfactant solution and in a mimber of different organic and acpieous media. These ratios are obtained from the H-NMR of the product mixtures, as has been described in Chapter 2. The results are summarised in Table 5.3, and clearly point towards a water-like environment for the Diels-Alder reaction in the presence of micelles, which is in line with literature observations. 

Barrelene was obtained via a double Diels-Alder reaction from a-pyrone with methyl acrylate (H.E. Zimmerman, I969A). The primarily forming bicyclic lactone decarboxylates in the heat, and the resulting cyclohexadiene rapidly undergoes another Diels-Alder cyclization. Standard reactions have then been used to eliminate the methoxycarbonyl groups and to introduce C—C double bonds. Irradiation of barrelene produces semibullvalene and cyclooctatetraene (H.E. Zimmerman. 1969B). 

As a typical example, the catalytic reaction of iodobenzene with methyl acrylate to afford methyl cinnamate (18) is explained by the sequences illustrated for the oxidative addition, insertion, and /3-elimination reactions. 

Diene carboxylates can be prepared by the reaction of alkenyl halides with acrylates[34]. For example, pellitorine (30) is prepared by the reaction of I-heptenyl iodide (29) with an acrylate[35]. Enol triflates are reactive pseudo-halides derived from carbonyl compounds, and are utilized extensively for novel transformations. The 3,5-dien-3-ol triflate 31 derived from a 4,5-unsaturated 3-keto steroid is converted into the triene 32 by the reaction of methyl acrylate[36]. 

A Heck reactions 1 l-Acetyl-3-bromoindole Methyl acrylate, PdiOAc), Ar,P, EtjN, DMF 50 [1]... 

Acetylation of acetaldehyde to ethyUdene diacetate [542-10-9], a precursor of vinyl acetate, has long been known (7), but the condensation of formaldehyde [50-00-0] and acetic acid vapors to furnish acryflc acid [97-10-7] is more recent (30). These reactions consume relatively more energy than other routes for manufacturing vinyl acetate or acryflc acid, and thus are not likely to be further developed. Vapor-phase methanol—methyl acetate oxidation using simultaneous condensation to yield methyl acrylate is still being developed (28). A vanadium—titania phosphate catalyst is employed in that process. 

Heteroatom functionalized terpene resins are also utilized in hot melt adhesive and ink appHcations. Diels-Alder reaction of terpenic dienes or trienes with acrylates, methacrylates, or other a, P-unsaturated esters of polyhydric alcohols has been shown to yield resins with superior pressure sensitive adhesive properties relative to petroleum and unmodified polyterpene resins (107). Limonene—phenol resins, produced by the BF etherate-catalyzed condensation of 1.4—2.0 moles of limonene with 1.0 mole of phenol have been shown to impart improved tack, elongation, and tensile strength to ethylene—vinyl acetate and ethylene—methyl acrylate-based hot melt adhesive systems (108). Terpene polyol ethers have been shown to be particularly effective tackifiers in pressure sensitive adhesive appHcations (109). 

Reaction conditions depend on the reactants and usually involve acid or base catalysis. Examples of X include sulfate, acid sulfate, alkane- or arenesulfonate, chloride, bromide, hydroxyl, alkoxide, perchlorate, etc. RX can also be an alkyl orthoformate or alkyl carboxylate. The reaction of cycHc alkylating agents, eg, epoxides and a2iridines, with sodium or potassium salts of alkyl hydroperoxides also promotes formation of dialkyl peroxides (44,66). Olefinic alkylating agents include acycHc and cycHc olefinic hydrocarbons, vinyl and isopropenyl ethers, enamines, A[-vinylamides, vinyl sulfonates, divinyl sulfone, and a, P-unsaturated compounds, eg, methyl acrylate, mesityl oxide, acrylamide, and acrylonitrile (44,66). 

Such copolymers of oxygen have been prepared from styrene, a-methylstyrene, indene, ketenes, butadiene, isoprene, l,l-diphen5iethylene, methyl methacrjiate, methyl acrylate, acrylonitrile, and vinyl chloride (44,66,109). 1,3-Dienes, such as butadiene, yield randomly distributed 1,2- and 1,4-copolymers. Oxygen pressure and olefin stmcture are important factors in these reactions for example, other products, eg, carbonyl compounds, epoxides, etc, can form at low oxygen pressures. Polymers possessing dialkyl peroxide moieties in the polymer backbone have also been prepared by base-catalyzed condensations of di(hydroxy-/ f2 -alkyl) peroxides with dibasic acid chlorides or bis(chloroformates) (110). 

The versatility of this reaction is extended to a variety of aldehydes. The bisphenol derived from 2,6-di-/ f2 -butylphenol and furfural, (25) where R = furfuryl (13), is also used as an antioxidant. The utility of the 3,5-di-/ f2 -butyl-4-hydroxyben2yl moiety is evident in stabili2ets of all types (14), and its effectiveness has spurred investigations of derivatives of hindered alkylphenols to achieve better stahi1i2ing quaUties. Another example is the Michael addition of 2,6-di-/ f2 -butyl phenol to methyl acrylate. This reaction is carried out under basic conditions and yields methyl... 

Methylphenol is converted to 6-/ f2 -butyl-2-methylphenol [2219-82-1] by alkylation with isobutylene under aluminum catalysis. A number of phenoHc anti-oxidants used to stabilize mbber and plastics against thermal oxidative degradation are based on this compound. The condensation of 6-/ f2 -butyl-2-methylphenol with formaldehyde yields 4,4 -methylenebis(2-methyl-6-/ f2 butylphenol) [96-65-17, reaction with sulfur dichloride yields 4,4 -thiobis(2-methyl-6-/ f2 butylphenol) [96-66-2] and reaction with methyl acrylate under base catalysis yields the corresponding hydrocinnamate. Transesterification of the hydrocinnamate with triethylene glycol yields triethylene glycol-bis[3-(3-/ f2 -butyl-5-methyl-4-hydroxyphenyl)propionate] [36443-68-2] (39). 2-Methylphenol is also a component of cresyHc acids, blends of phenol, cresols, and xylenols. CresyHc acids are used as solvents in a number of coating appHcations (see Table 3). 

Michael-Type Additions. Michael additions are generally used to prepare methyl 3-mercaptopropionate (eq. 10) and mercaptopropionitrile (eq. 11) by the reaction of methyl acrylate or acrylonitrile and hydrogen sulfide using a basic catalyst. This reaction proceeds as shown ... 

The reaction is carried out in the Hquid phase at 373—463 K and 3 MPa (30 atm) of carbon monoxide pressure using nickel salt catalyst, or at 313 K and 0.1 MPa (1 atm) using nickel carbonyl as both the catalyst and the source of carbon monoxide. Either acryHc acid or methyl acrylate may be produced directly, depending on whether water or methanol is used as solvent (41). New technology for acryHc acid production uses direct propjdene oxidation rather than acetylene carbonylation because of the high cost of acetjdene. This new process has completely replaced the old in the United States (see... 

Hydroxycoumarias can be obtained by reaction of methyl acrylate [96-33-3] with diphenols ia the preseace of aluminum chloride followed by dehydrogeaatioa with palladium oa carboa (43). 

Acrylic Esters. A procedure has been described for preparation of higher esters from methyl acrylate that illustrates the use of an acid catalyst together with the removal of one of the products by azeotropic distillation (112). Another procedure for the preparation of butyl acrylate, secondary alkyl acrylates, and hydroxyalkyl acrylates using -toluenesulfonic acid as a catalyst has been described (113). Alurninumisopropoxide catalyzes the reaction of amino alcohols with methyl acrylate and methyl methacrylate. A review of the synthesis of acryhc esters by transesterification is given in Reference 114 (see... 

Jap-KIingermarm reactions, 4, 301 oxidation, 4, 299 reactions, 4, 299 synthesis, 4, 362 tautomerism, 4, 38, 200 Indole, 5-amino-synthesis, 4, 341 Indole, C-amino-oxidation, 4, 299 tautomerism, 4, 298 Indole, 3-(2-aminobutyl)-as antidepressant, 4, 371 Indole, (2-aminoethyl)-synthesis, 4, 278 Indole, 3-(2-aminoethyl)-synthesis, 4, 337 Indole, aminomethyl-reactions, 4, 71 Indole, 4-aminomethyl-synthesis, 4, 150 Indole, (aminovinyl)-synthesis, 4, 286 Indole, 1-aroyl-oxidation, 4, 57 oxidative dimerization catalysis by Pd(II) salts, 4, 252 Indole, 1-aroyloxy-rearrangement, 4, 244 Indole, 2-aryl-nitration, 4, 211 nitrosation, 4, 210 synthesis, 4, 324 Indole, 3-(arylazo)-rearrangement, 4, 301 Indole, 3-(arylthio)-synthesis, 4, 368 Indole, 3-azophenyl-nitration, 4, 49 Indole, 1-benzenesulfonyl-by lithiation, 4, 238 Indole, 1-benzoyl photosensitized reactions with methyl acrylate, 4, 268 Indole, 3-benzoyl-l,2-dimethyl-reactions... 

Vinyl ethers undergo many cycloaddition reactions similar to those which take place with enamines. In general, however, these cycloaddition reactions with vinyl ethers take place less readily than those with enamines. These reactions include cycloaddition of vinyl ethers with ketene (200-205), phenyl isocyanate (206), sulfene (207,208), methyl acrylate (209), diethyl acetylenedicarboxylate (210), and diphenylnitrilimine (183). 

The formation of an enamine from an a,a-disubstituted cyclopentanone and its reaction with methyl acrylate was used in a synthesis of clovene (JOS). In a synthetic route to aspidospermine, a cyclic enamine reacted with methyl acrylate to form an imonium salt, which regenerated a new cyclic enamine and allowed a subsequent internal enamine acylation reaction (309,310). The required cyclic enamine could not be obtained in this instance by base isomerization of the allylic amine precursor, but was obtained by mercuric acetate oxidation of its reduction product. Condensation of a dihydronaphthalene carboxylic ester with an enamine has also been reported (311). 

---