Metal test result

Schiff s test. Dissolve about o i g. of uric acid in NsjCOj solution and pour some of this solution on to a filter-paper which has been moistened with AgNO solution a black stain of metallic silver results. 

Heat Transfer from Various Metal Surfaces In an early work, Pridgeon and Badger [Jnd. Eng. Chem., 16, 474 (1924)] pubhshed test results on copper and iron tubes in a horizontal-tube evaporator that indicated an extreme effect of surface cleanliness on heat-transfer coefficients. However, the high degree of cleanhness needed for high coefficients was difficult to achieve, and the tube layout and... 

The total releases to air from the facility must be entered m Part III, Section 5 of Form R in pounds per year. The stack test results provide the concentration of metallic lead in each exhaust stream in grains per cubic toot and the exhaust rate in cubic feet per minute. Using the appropriate conversion factors, knowing the scrubber efficiency (from the manufacturer s data), and assuming yourfacility operates 24 hours per day, 300 days per year, you can calculate the total lead releases from the stack test data. Because point (stack) releases of lead are 2,400 pounds per year,-which is greater than the 999 pounds per year ranges in column A. 1, you must enter the actual calculated amount in column A.2 of Section 5.2. 

Because cast iron components are normally very heavy in section, the relatively low rates of attack associated with atmospheric corrosion do not constitute a problem and little work has been carried out on the phenomenon. A summary of some of the data available is given in Table 3.42. The most extensive work in this field was initiated by the A.S.T.M. in 1958 and some of the results produced by these studies are quoted in Table 3.43. It will be noted that there is a marked fall in corrosion rate with time for all the metals tested. 

Static test results may be evaluated by measurement of change of mass or section thickness, but metallographic and X-ray examination to determine the nature and extent of attack are of greater value because difficulty can be encountered in removing adherent layers of solidified corrodent from the surface of the specimen on completion of the exposure, particularly where irregular attack has occurred. Changes in the corrodent, ascertained by chemical analysis, are often of considerable value also. In view of the low solubility of many construction materials in liquid metals and salts, changes in mass or section thickness should be evaluated cautiously. A limited volume of liquid metal could become saturated early in the test and the reaction would thus be stifled when only a small corrosion loss... 

The corrosion rates of the materials of construction are always of importance, but it has been found that, whereas the uniform removal of metal from the hot leg may not impair the load-carrying ability of the container, the deposition of metal in the cold leg can cause the cessation of flow, and the measure of the suitability of an alloy is often the time, under given conditions, that it takes for plugging to occur. Again, the flow velocity and the cross-sectional area are of primary importance in relating test results to operating conditions. 

V2O5-P205 (95 5, molar ratio) cathode and a lithium anode (Li/a-V205 cell) [1]. In this section, we describe safety test results for AA Li/a- V2Os cells. The AA cell we fabricated has a pressure vent, a Polyswitch (PS, Raychem Co., thermal and current fuse) and is composed of a spirally wound cathode sheet, a metallic Li-based anode sheet and a polyethylene (PE) separator [87]. 

Test results are presented and discussed following trials in which energy recovery of mixed plastics domestic waste and municipal solid waste was carried out by means of co-combustion. The research also involved the collection of data relating to emissions, and the levels of halogens, dioxins and furans and heavy metals within the mixed plastics waste. 

Spirodela intermedia, L. minor, and P. stratiotes were able to remove Pb(II), Cd(II), Ni(II), Cu(II), and Zn(II), although the two former ions were removed more efficiently. Data fitted the Langmuir model only for Ni and Cd, but the Freundlich isotherm for all metals tested. The adsorption capacity values (K ) showed that Pb was the metal more efficiently removed from water solution (166.49 and 447.95 mg/g for S. intermedia and L. minor, respectively). The adsorption process for the three species studied followed first-order kinetics. The mechanism involved in biosorption resulted in an ion-exchange process between monovalent metals as counterions present in the macrophytes biomass and heavy metal ions and protons taken up from water.112... 

This technology has broad applicability. For instance, using the same carbon support, test results show that a new Pt/C catalyst with edge-metal location and low dispersion resulted in 36% more activity than ESCAT 20 in a standard nitrobenzene (SNB) test (Figure 6). Using the same technology with a different carbon support yielded a catalyst with 57% more activity than ESCAT 20 in SNB test (16,17). 

Commercial coated samples were obtained. Coating thickness was nominal 2 mils for organic-metal filled coatings (approximately 50% metal filler). Zinc metal coatings were zinc arc spray and were thicker, 5 mils, but normal for that process. Test results for each fire parameter are given as follows ... 

All pressure retaining steels applied at a specified minimum design metal temperature (2.11.4.5) below -30°C (-20°F) require a Charpy V-notch impact test of the base metal and the weld joint unless they are exempt in accordance with the requirements of paragraph UHA-51 in Section Vlll, Division 1 of the ASME Code. Impact test results shall meet the requirements of paragraph UG-84 of the Code. 

The ionic phosphonates like NTMP are effective hydration inhibitors because they can form an insoluble complex with the oxide surface. They are useful as epoxy adhesive couplers in cases where the adhesive and its curing cycle are compatible with the adsorbed phosphonate molecule. (14) Wedge test results indicate that in two epoxy-aluminum systems studied, certain organosilanes tend to both increase the epoxy-metal bond durability and maintain hydration resistance. The results of anodic polarization experiments further suggest that these silane films are effective against localized pitting. 

Extensive testing has been performed with solutions of NaCl and NaNOs. Test results indicate the CA-CDI system can effectively remove heavy metals including copper, manganese, zinc, cadmium, cobalt, chromium, lead, and uranium from aqueous process streams and natural waters. 

---