Mass transport chemical kinetics

Electroactive polymers have a number of attractive features that account for this continuing interest. First they present a distributed array of catalytic sites. Thus in contrast to monolayer chemically modified electrodes, there are potentially a much greater number of reactive sites that can contribute to the catalytic current. Since these sites are distributed throughout the film, it is essential to consider the mass transport of reagents into the film and the mass transport of products out of these films when studying the overall kinetics of these processes. The coupled mass transport and kinetics in redox polymer films have been investigated in some detail, and good models exist for these processes. ... 

Double potential steps are usefiil to investigate the kinetics of homogeneous chemical reactions following electron transfer. In this case, after the first step—raising to a potential where the reduction of O to occurs under diffrision control—the potential is stepped back after a period i, to a value where tlie reduction of O is mass-transport controlled. The two transients can then be compared and tlie kinetic infomiation obtained by lookmg at the ratio of... 

The productivity of DR processes depeads oa chemical kinetics, as weU as mass and heat transport factors that combine to estabhsh the overall rate and extent of reduction of the charged ore. The rates of the reduction reactions are a function of the temperature and pressure ia the reductioa beds, the porosity and size distribution of the ore, the composition of the reduciag gases, and the effectiveness of gas—sohd contact ia the reductioa beds. The reductioa rate geaerahy iacreases with increasing temperature and pressure up to about 507 kPa (5 atm). 

The scientific basis of extractive metallurgy is inorganic physical chemistry, mainly chemical thermodynamics and kinetics (see Thermodynamic properties). Metallurgical engineering reties on basic chemical engineering science, material and energy balances, and heat and mass transport. Metallurgical systems, however, are often complex. Scale-up from the bench to the commercial plant is more difficult than for other chemical processes. 

In the former case, the rate is independent of the diffusion coefficient and is determined by the intrinsic chemical kinetics in the latter case, the rate is independent of the rate constant k and depends on the diffusion coefficient the reaction is then diffusion controlled. This is a different kind of mass transport influence than that characteristic of a reactant from a gas to ahquid phase. 

Figure 10 shows that Tj is a unique function of the Thiele modulus. When the modulus ( ) is small (- SdSl), the effectiveness factor is unity, which means that there is no effect of mass transport on the rate of the catalytic reaction. When ( ) is greater than about 1, the effectiveness factor is less than unity and the reaction rate is influenced by mass transport in the pores. When the modulus is large (- 10), the effectiveness factor is inversely proportional to the modulus, and the reaction rate (eq. 19) is proportional to k ( ), which, from the definition of ( ), implies that the rate and the observed reaction rate constant are proportional to (1 /R)(f9This result shows that both the rate constant, ie, a measure of the intrinsic activity of the catalyst, and the effective diffusion coefficient, ie, a measure of the resistance to transport of the reactant offered by the pore stmcture, influence the rate. It is not appropriate to say that the reaction is diffusion controlled it depends on both the diffusion and the chemical kinetics. In contrast, as shown by equation 3, a reaction in solution can be diffusion controlled, depending on D but not on k. 

Mass transfer and chemical kinetic factors in CVD include the flow of initial substances and gaseous products through the system, the transport of reactants from the gas phase to the substrate surface, the transport of the gaseous products from the substrate surface to the bulk gas, as well as the reactions taking place at the substrate surface . ... 

The Chemkin package deals with problems that can be stated in terms of equation of state, thermodynamic properties, and chemical kinetics, but it does not consider the effects of fluid transport. Once fluid transport is introduced it is usually necessary to model diffusive fluxes of mass, momentum, and energy, which requires knowledge of transport coefficients such as viscosity, thermal conductivity, species diffusion coefficients, and thermal diffusion coefficients. Therefore, in a software package analogous to Chemkin, we provide the capabilities for evaluating these coefficients. ... 

The effect of chemical kinetics on mass transport in incompressible flows is summarized by the reaction term r in Eq. (89). Applied to a chemical species a, it describes the rate of disappearance of this species per unit volume ... 

A significant advance was made in this field by Watarai and Freiser [58], who developed a high-speed automatic system for solvent extraction kinetic studies. The extraction vessel was a 200 mL Morton flask fitted with a high speed stirrer (0-20,000 rpm) and a teflon phase separator. The mass transport rates generated with this approach were considered to be sufficiently high to effectively outrun the kinetics of the chemical processes of interest. With the aid of the separator, the bulk organic phase was cleanly separated from a fine dispersion of the two phases in the flask, circulated through a spectrophotometric flow cell, and returned to the reaction vessel. 

In order to investigate the dependence of a fast reaction on the nature of the metal, Iwasita et al. [3] measured the kinetics of the [Ru(NH,3)6]2+/3+ couple on six different metals. Since this reaction is very fast, with rate constants of the order of 1 cm s-1, a turbulent pipe flow method (see Chapter 14) was used to achieve rapid mass transport. The results are summarized in Table 8.1 within the experimental accuracy both the rate constants and the transfer coefficients are independent of the nature of the metal. This remains true if the electrode surfaces axe modified by metal atoms deposited at underpotential [4]. It should be noted that the metals investigated have quite different chemical characteristics Pt, and Pd are transition metals Au, Ag, Cu are sd metals Hg and the adsorbates T1 and Pb are sp metals. The rate constant on mercury involved a greater error than the others... 

An interesting approach to measuring rates of electron transfer reactions at electrodes is through the study of surface bound molecules (43-451. Molecules can be attached to electrode surfaces by irreversible adsorption or the formation of chemical bonds (461. Electron transfer kinetics to and from surface bound species is simplified because there is no mass transport and because the electron transfer distance is controlled to some degree. 

The actual processes of uptake of chemical species by an organism typically encompass transport in the medium, adsorption at extracellular cell wall components, and internalisation by transfer through the cell membrane. Each of these steps constitutes a broad spectrum of physicochemical aspects, including chemical interactions between relevant components, electrostatic interactions, elementary chemical kinetics (in this volume, as pertains to the interface), diffusion limitations of mass transfer processes, etc. 

As suggested before, the role of the interphasial double layer is insignificant in many transport processes that are involved with the supply of components from the bulk of the medium towards the biosurface. The thickness of the electric double layer is so small compared with that of the diffusion layer 8 that the very local deformation of the concentration profiles does not really alter the flux. Hence, in most analyses of diffusive mass transport one does not find any electric double layer terms. For the kinetics of the interphasial processes, this is completely different. Rate constants for chemical reactions or permeation steps are usually heavily dependent on the local conditions. Like in electrochemical processes, two elements are of great importance the local electric field which affects rates of transfer of charged species (the actual potential comes into play in the case of redox reactions), and the local activities... 

In the biomedical literature (e.g. solute = enzyme, drug, etc.), values of kf and kr are often estimated from kinetic experiments that do not distinguish between diffusive transport in the external medium and chemical reaction effects. In that case, reaction kinetics are generally assumed to be rate-limiting with respect to mass transport. This assumption is typically confirmed by comparing the adsorption transient to maximum rates of diffusive flux to the cell surface. Values of kf and kr are then determined from the start of short-term experiments with either no (determination of kf) or a finite concentration (determination of kT) of initial surface bound solute [189]. If the rate constant for the reaction at the cell surface is near or equal to (cf. equation (16)), then... 

This section and the next are dedicated to the basics of the silicon-electrolyte contact with focus on the electrolyte side of the junction and the electrochemical reactions accompanying charge transfer. The current across a semiconductor-electrolyte junction may be limited by the mass transport in the electrolyte, by the kinetics of the chemical reaction at the interface, or by the charge supply from the electrode. The mass transport in the bulk of the electrolyte again depends on convection as well as diffusion. In a thin electrolyte layer of about a micrometer close to the electrode surface, diffusion becomes dominant The stoichiometry of the basic reactions at the silicon electrode will be presented first, followed by a detailed discussion of the reaction pathways as shown in Figs. 4.1-4.4. 

The main goal of this chapter is to review the most widely used modeling techniques to analyze sorption/desorption data generated for environmental systems. Since the definition of sorption/desorption (i.e., a mass-transfer mechanism) process requires the determination of the rate at which equilibrium is approached, some important aspects of chemical kinetics and modeling of sorption/desorption mechanisms for solid phase systems are discussed. In addition, the background theory and experimental techniques for the different sorption/ desorption processes are considered. Estimations of transport parameters for organic pollutants from laboratory studies are also presented and evaluated. 

Brett, C. M. A. and Brett A. M. C. F. O., Hydrodynamic Electrodes , in Comprehensive Chemical Kinetics, Vol. 27, Bamford, C. H. and Compton R. G. (Eds), Elsevier, Amsterdam, 1986, pp. 355-441. This monograph provides a thorough and useful introduction to the topics of mass transport and convection-based electrodes. It also contains one of the better discussions on flow systems, in part because it can be read quite easily despite the overall treatment being so overtly mathematical. 

The reaction order of one is also in good accordance with the film theory, where the rate of mass transport linearly correlates with the equilibrium concentration of citral in the aqueous phase. As a matter of fact, the mass transport rate is of first order regarding the substrate concentration in the organic phase. Therefore, what is measured is in fact the rate of mass transport and not the rate of chemical reaction. This result is in our opinion a good example of how kinetic parameters could be falsified when the reaction is limited by mass transport and not kinetics. 

---