Adsorption irreversible

There are numerous references in the literature to irreversible adsorption from solution. Irreversible adsorption is defined as the lack of desotption from an adsoibed layer equilibrated with pure solvent. Often there is no evidence of strong surface-adsorbate bond formation, either in terms of the chemistry of the system or from direct calorimetric measurements of the heat of adsorption. It is also typical that if a better solvent is used, or a strongly competitive adsorbate, then desorption is rapid and complete. Adsorption irreversibility occurs quite frequently in polymers [4] and proteins [121-123] but has also been observed in small molecules and surfactants [124-128]. Each of these cases has a different explanation and discussion. 

An example of the time effects in irreversible adsorption of a surfactant system is shown in Fig. XI-8 for barium dinonylnapthalene sulfonate (an oil additive) adsorbing on Ti02 (anatase). Adsorption was ineversible for aged systems, but much less so for those equilibrating for a short time. The adsorption of aqueous methylene blue (note Section XI-4) on TiOi (anatase) was also irreversible [128]. In these situations it seems necessary to postulate at least a two-stage sequence, such as... 

Irreversible adsorption discussed in Section XI-3 poses a paradox. Consider, for example, curve 1 of Fig. XI-8, and for a particular system let the equilibrium concentration be 0.025 g/lOO cm, corresponding to a coverage, 6 of about 0.5. If the adsorption is irreversible, no desorption would occur on a small dilution on the other hand, more adsorption would occur if the concentration were increased. If adsorption is possible but not desorption, why does the adsorption stop at 6 = 0.5 instead of continuing up to 0 = 1 Comment on this paradox and on possible explanations. 

Jin X, Wang NHL, Tarjus G and Talbot J 1993 Irreversible adsorption on nonuniform surfaoes the random site model J. Phys. Chem. 97 4256-8... 

There are different reasons to discard a column a column can be damaged by irreversible adsorption of reactive polymer samples. Small amounts of styrene oligomers are known to permanently elute from styrene-divinylbenzene materials with tetrahydrofuran as the eluent, which means a continuous shear degradation of the separation material and consequently a decrease of the packing quality this observation is very important if fractions are collected and used for further analyses, e.g., for the determination of infrared (IR) spectra. One can presume that similar effects are present with other organic materials too. 

This exchangeability of adsorbed layers should be considered for better understanding of the irreversible adsorption of polymers. Apparently, penetration by the macromolecules adsorbed later through the layer of the initially adsorbed ones will include a slow exchange between the positions of segments and take a longer time. 

Depending on the nature of the system, the adsorption process can be either reversible or irreversible. In the first case an adsorption equilibrium exists between the particles adsorbed on the adsorbent s surface and the particles in the electrolyte (or in any other phase contacting with the adsorbent). After removing the substance from the electrolyte, adsorbed particles leave the surface and reenter into the electrolyte. In the case of an irreversible adsorption, the adsorbed particles remain at the surface even if their concentration in the bulk phase drops to zero. In this case the adsorbed particles can be removed from the surface only by means of a chemical reaction... 

The process for this irreversible adsorption has not been investigated in detail. The mechanism by which the metal is deposited has not been unambiguously elucidated, and several possibilities have been proposed. One possibility is the formation of local cells, with the ion of the adatom being reduced and either hydrogen [Szabo and Nagy, 1978] or platinum [Clavilier et al., 1988] being oxidized ... 

Clavilier J, Orts JM, EeUu JM, Aldaz A. 1990b. Study of the conditions for irreversible adsorption of lead at Pt(M/) electrodes. J Electroanal Chem 293 197-208. 

Silica gels with mean pore diameters of 5-15 nm and surface areas of 150-600 m /g have been preferred for the separation of low molecular weight samples, while silica gels with pore diameters greater than 30 nm are preferred for the separation, of biopolymers to avoid restricting the accessibility of the solutes to the stationary phase [15,16,29,34]. Ideally, the pore size distribution should be narrow and symmetrical about the mean value. Micropores are particularly undesirable as they may give rise to size-exclusion effects or irreversible adsorption due to... 

The most spectacular results with temperature-programmed LC have been obtained for some notoriously difficult polymeric additives. Characterisation of the oligomeric HALS stabiliser poly [[6-[(l,l,3,3-te-tramethylbutyl) amino]-l,3,5-triazine-2,4-diyl][(2,2,6,6-tetramethyl-4-piperidyl)imino]-l,6-hexanediyl [(2,2,6,6-tetramethyl-4-piperidyl)imino]] (I) (Figure 4.12) is difficult for several reasons it has a broad MWD, may contain isomers, and has several amino groups that promote almost irreversible adsorption to silica based column packings in LC. 

The coefficient actually measures multiple processes (reversible and irreversible adsorption, precipitation, and coprecipitation). Consequently, it is a purely empirical number with no theoretical basis on which to predict adsorption under differing environmental conditions or to give information on the types of bonding mechanisms involved. 

An assumption implicit in most adsorption studies is that adsorption is fully reversible. In other words, once the empirical coefficients are measured for a particular substance, Equations 20.6 to 20.10 describe both adsorption and desorption isotherms. This assumption is not always true. Collins and Crocker140 observed apparently irreversible adsorption of phenol in flowthrough adsorption experiments involving phenol interacting on a Frio sandstone core under simulated deep-well... 

Experiment B is also a non-adsorption experiment in which flow through the capillary tube is used. The sample medium used is the surfactant solution prepared in the 1% acidified brine. Results will be combined with those from Experiment C to get the information on the permanent or irreversible adsorption on the porous medium by measuring peak areas. 

---