Lead, electrochemical analytical methods

The methods most commonly used to detect hydrogen sulfide in environmental samples include GC/FPD, gas chromatography with electrochemical detection (GC/ECD), iodometric methods, the methylene blue colorimetric or spectrophotometric method, the spot method using paper or tiles impregnated with lead acetate or mercuric chloride, ion chromatography with conductivity, and potentiometric titration with a sulfide ion-selective electrode. Details of commonly used analytical methods for several types of environmental samples are presented in Table 6-2. 

Brugmann [784] discussed different approaches to trace metal speciation (bioassays, computer modelling, analytical methods). The electrochemical techniques include conventional polarography, ASV, and potentiometry. ASV diagnosis of seawater was useful for investigating the properties of metal complexes in seawater. Differences in the lead and copper values yielded for Baltic seawater by methods based on differential pulse ASV or AAS are discussed with respect to speciation. 

How much lead is in your municipal drinking water Is platinum present in the urine of a chemotherapy patient Can plants purify water through cadmium uptake Can the amount and location of zinc ions be detected in neurons The detection of trace amounts of metal ions is a central analytical method in environmental and biological chemistry. Often, a reagent that can coordinate to a metal ion of interest is added to a sample solution and the resulting metal complex is detected using analytical instrumentation. Electrochemical and fluorescence detection are two of the most sensitive methods. 

Electrochemical sensors have major advantages over traditional analytical methods, which will certainly lead to their even more pronounced use in the near future. They are attractive analytical devices due to their inherent sensitivity and selectivity towards electroactive species, sometimes even due to specificity, accurate and short response times, adaptability, and simplicity of preparation. They are compact, portable, and easy to use they have a high benefit/cost ratio and present quickness in data collection. 

In contrast, the coupling of electrochemical and spectroscopic techniques, e.g., electrodeposition of a metal followed by detection by atomic absorption spectrometry, has received limited attention. Wire filaments, graphite rods, pyrolytic graphite tubes, and hanging drop mercury electrodes have been tested [383-394] for electrochemical preconcentration of the analyte to be determined by atomic absorption spectroscopy. However, these ex situ preconcentration methods are often characterised by unavoidable irreproducibility, contaminations arising from handling of the support, and detection limits unsuitable for lead detection at sub-ppb levels. 

The Dimensionless Parameter is a mathematical method to solve linear differential equations. It has been used in Electrochemistry in the resolution of Fick s second law differential equation. This method is based on the use of functional series in dimensionless variables—which are related both to the form of the differential equation and to its boundary conditions—to transform a partial differential equation into a series of total differential equations in terms of only one independent dimensionless variable. This method was extensively used by Koutecky and later by other authors [1-9], and has proven to be the most powerful to obtain explicit analytical solutions. In this appendix, this method will be applied to the study of a charge transfer reaction at spherical electrodes when the diffusion coefficients of both species are not equal. In this situation, the use of this procedure will lead us to a series of homogeneous total differential equations depending on the variable, v given in Eq. (A.l). In other more complex cases, this method leads to nonhomogeneous total differential equations (for example, the case of a reversible process in Normal Pulse Polarography at the DME or the solutions of several electrochemical processes in double pulse techniques). In these last situations, explicit analytical solutions have also been obtained, although they will not be treated here for the sake of simplicity. 

Reversed-phase high-performance liquid chromatography (RP-HPLC) is the usual method of choice for the separation of anthocyanins combined with an ultraviolet-visible (UV-Vis) or diode-array detector (DAD)(Hebrero et al., 1988 Hong et ah, 1990). With reversed-phase columns the elution pattern of anthocyanins is mainly dependent on the partition coefficients between the mobile phase and the Cjg stationary phase, and on the polarity of the analytes. The mobile phase consists normally of an aqueous solvent (water/carboxylic acid) and an organic solvent (methanol or acetonitrile/carboxylic acid). Typically the amount of carboxylic acid has been up to 10%, but with the addition of a mass spectrometer as a detector, the amount of acid has been decreased to as low as 1 % with a shift from trifluoroacetic acid to formic acid to prevent quenching of the ionization process that may occur with trifluoroacetic acid. The acidic media allows for the complete displacement of the equilibrium to the fiavylium cation, resulting in better resolution and a characteristic absorbance between 515 and 540 nm. HPLC separation methods, combined with electrochemical or DAD, are effective tools for anthocyanin analysis. The weakness of these detection methods is a lack of structural information and some nonspecificity leading to misattribution of peaks, particularly with electrochemical... 

The aim of this chapter is to show that the choice of a catalyst formulation leading to increase the activity and the selectivity of a given electrochemical reaction involved in a fuel cell can only be achieved when the mechanism of the electrocatalytic reaction is sufficiently understood. The elucidation of the mechanism caimot be obtained by using only electrochemical techniques (e.g. cyclic voltammetry, chronopotentiometry, chrono-amperometiy, coulo-metry, etc.), and usually needs a combination of such techniques with spectroscopic and analytical techniques. A detailed study of the reaction mechanism has thus to be carried out with spectroscopic and analytical techniques under electrochemical control. In short, the combination of electrochemical methods with other physicochemical methods cannot be disputed to determine some key reaction steps. For this purpose, it is then necessary to be able to identify the nature of adsorbed intermediates, the stractuie of adsorbed layers, the natirre of the reaction products and byproducts, etc., and to determine the amormt of these species, as a fimction of the electrode potential and experimental conditions. 

The methods of coulometry are based on the measurement of the quantity of electricity involved in an electrochemical electrolysis reaction. This quantity is expressed in coulombs and it represents the product of the current in amperes by the duration of the current flow in seconds. The quantity of electricity thus determined represents, through the laws of Faraday, the equivalents of reactant associated with the electrochemical reaction taking place at the electrode of significance. In the analytical chemistry sense, the process of coulometry, carried out to the quantitative reaction of the analyte in question, either directly or indirectly, will yield the number of analyte equivalents involved in the sample under test. This will lead to a quantitative determination of the analyte in the sample. Analytical coulometry can be carried out either directly or indirectly. In the former the analyte usually reacts directly at the surface of either the anode or cathode of the electrolysis cell. In the latter, the analyte reacts indirectly with a reactant produced by electrolytic action at one of the electrodes in the electrolysis cell. In either case, the determination will hinge on the number of coulombs consumed in the analytical process. 

Electropolymerization of a functionalized precursor represents a straightforward method for the realization of modified electrodes endowed with specific electrochemical or optical properties. Electrode materials based on electrogenerated functional conjugated polymers and their application as electrochemical sensors have been already reviewed [162-165]. On the other hand, the sensitivity of the optical properties of ir-conjugated polymers to conformational changes has led to the realization of colorimetric sensors for the detection of various analytes extending from alkali metal ions to anions and biomolecules [165-168]. In general, the realization of sensors based on functional PTs relies on the fact that complexation at a side chain may lead to perturbation of the polymer conformation, which can be read by either electrochemical or optical methods. 

---