Grafted with glycidyl methacrylate

Nakahara, Y. Dyeing of cuprammonium staple fiber grafted with glycidyl methacrylate. J. Soc. Text, and Cell. Ind. (Japan) 20, 319 (1964). 

This product is then further grafted with glycidyl methacrylate. 

PO grafted with glycidyl methacrylate, acrylamide, vinylpyrrolidone, acrylic acid esters, and/or methacrylic acid esters and then blended with PA or PEST Two-stage, reactive impact modification preparation of reactive compatibilizer and then blending Teraya et al. 1994... 

Styrene and acrylonitrile copolymer Styrene, butadiene and styrene copolymer Styrene, ethylene, butylenes and styrene copolymer Styrene, ethylene, butylenes and styrene copolymer grafted with glycidyl methacrylate Styrene, ethylene, butylenes and styrene copolymer grafted with maleic anhydride Styrene maleic anhydride Syndiotactic polystyrene... 

Ko JM, Min BG, Kim DW, Ryu KS, Kim KM, Le YG, Chang SH (2004) Thin-film type Li-ion battery, using a polyethylene separator grafted with glycidyl methacrylate. Electrochim Acta 50 367-370... 

Ethylene-propylene copolymers grafted with glycidyl methacrylates... 

Q. Wei, D. Chionna, E. Galoppini, and M. Pracella, Fxmctionalization of LDPE by melt grafting with glycidyl methacrylate and reactive blending with polyamide-6, Macromol. Chem. Phys., 204(8) 1123-1133, May 2003. 

EPDM PBT EPDM grafted with glycidyl methacrylate and cured with peroxide or 6-aminohexyl carbamic acid 83... 

EPR grafted with maleic anhydride ethylene-co-vinyl acetate copolymer high density polyethylene HDPE grafted with glycidyl methacrylate... 

Compatibilizer ABS copolymers have been prepared via an emulsion polymerization process. These copolymers have been functionalized with glycidyl methacrylate (GMA). The functionalized copolymers are blended PBT. Characterization by thermal mechanical analysis indicates that PBT is partially miscible with ABS and the glycidyl grafted ABS (48). 

Polymers of MMA, AAc, and MAA were grafted onto an ultrahigh molecular weight polyethylene (UHMWPE) fiber surface after pretreatment with electron beam irradiation [31]. Sundell et al. [32] pretreated a PE film with electron beams to facilitate the graft polymerization of vinyl benzylchloride onto the substrate. The inner surface of porous PE hollow fiber had also been modified by grafting of glycidyl methacrylate (GMA) polymer after electron beam irradiation [33]. 

Graft copolymers of cellulose with glycidyl methacrylate yield cation-exchange materials with sodium hydrogen sulfite100) and cationites with ammonia, monoethanolamine and diethylamine. 

Another alternative is the use of crosslinked ethylene dimethacrylate [33]. Here, the unreacted double bonds in resins were used as a graft point for further reaction. The level of unreacted double bonds was determined by the relative areas of the carbonyl peaks at 176.3 and 166.3 ppm (Fig. 15.2.34) determined by CP/MAS before and after reaction with glycidyl methacrylate. These results were in good agreement with data from Raman spectroscopy. 

Benzene can be separated over cyclohexane with an revalue of 26 with a polvinyl alcohol-poly(allylamine) blend containing a cobalt(II) complex.213 An a-value of 60 has been obtained by pervaporation with a poly(acrylonitrile-co-methyl methacrylate) membrane.214 Membranes of porous polyethylene grafted with glycidyl methacrylate215 and poly(A,A-dimethylacrylamide-co-methyl methacrylate)216 have also been used in this separation with separation factors of 21-22. This is a separation that would be difficult to do by size and by distillation. The two boil only 2°C apart. The cyclohexane produced by the reduction of benzene is the starting material for nylon. The best solution to the problem is to run the reduction to 100% completion. 

Chen YJ, Kang ET, Neoh KG, Tan KL. Surface functionalization of poly(tetra luoroethy-lene) films via consecutive graft copolymerization with glycidyl methacrylate and aniline. J Phys Chem B 2000 104(39) 9171-8. 

Y. Li, X. Dong, Y. Liu, J. Li, and F. Wang, Improvement of decay resistance of wood via combination treatment on wood cell wall Swell-bonding with maleic anhydride and graft copolymerization with glycidyl methacrylate and methyl methacrylate. Int. Biodeter. Biodegrad. 65 (7), 1087-1094(2011). 

Qin et al. [114] prepared functionalized single-walled carbon nanotubes (SWNTs) through treatment of polystyrene via the grafting-to method. The results showed that the PS was covalently attached to the side walls of SWNTs. The poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) was functionalized with glycidyl methacrylate (GMA) via atom transfer-radical polymerization (ATRP) and the BaTiOs nanoparticles were modified by amino-terminated silane molecules. Then, the nanocomposites with high dielectric coti-stant and high thermal conductivity were prepared by a grafting to method [115]. 

---