Reformer furnace

MIDREX Process. The primary components of a MID REX process plant include the shaft furnace, reformer, and heat recuperator. These components are supported by ancillary systems for handling iron ore, gas, water, and direct reduced iron. A flow sheet is shown in Figure 1. 

Steam Reforming. In steam reforming, light hydrocarbon feeds ranging from natural gas to straight mn naphthas are converted to synthesis gas (H2, CO, CO2) by reaction with steam (qv) over a catalyst in a primary reformer furnace. This process is usually operated at 800—870°C and 2.17—2.86... 

Naphtha desulfurization is conducted in the vapor phase as described for natural gas. Raw naphtha is preheated and vaporized in a separate furnace. If the sulfur content of the naphtha is very high, after Co—Mo hydrotreating, the naphtha is condensed, H2S is stripped out, and the residual H2S is adsorbed on ZnO. The primary reformer operates at conditions similar to those used with natural gas feed. The nickel catalyst, however, requires a promoter such as potassium in order to avoid carbon deposition at the practical levels of steam-to-carbon ratios of 3.5—5.0. Deposition of carbon from hydrocarbons cracking on the particles of the catalyst reduces the activity of the catalyst for the reforming and results in local uneven heating of the reformer tubes because the firing heat is not removed by the reforming reaction. 

The first naphtha steam-reforming furnaces were operated by ICl in the U.K. There are now many similar plants in operation all over the world. 

Fresh reducing gas is generated by reforming natural gas with steam. The natural gas is heated in a recuperator, desulfurized to less than 1 ppm sulfur, mixed with superheated steam, further preheated to 620°C in another recuperator, then reformed in alloy tubes filled with nickel-based catalyst at a temperature of 830°C. The reformed gas is quenched to remove water vapor, mixed with clean recycled top gas from the shaft furnace, reheated to 925°C in an indirect fired heater, and injected into the shaft furnace. For high (above 92%) metallization a CO2 removal unit is added in the top gas recycle line in order to upgrade the quaUty of the recycled top gas and reducing gas. 

Steam Reformings of Natural Gas. This route accounts for at least 80% of the world s methanol capacity. A steam reformer is essentially a process furnace in which the endothermic heat of reaction is provided by firing across tubes filled with a nickel-based catalyst through which the reactants flow. Several mechanical variants are available (see Ammonia). 

The primary reformer is essentially a process furnace in which fuel is burned with air to indirectiy provide the heat of reaction to the catalyst contained within tubes. This area of the furnace is usually referred to as the radiant section, so named because this is the primary mechanism for heat transfer at the high (750—850°C) temperatures required by the process. Reforming pressures in the range 3 —4 MPa (30,000—40,000 atm) represent a reasonable compromise between cost and downstream compression requirements. 

Fig. 13. Radiant section of a Kellogg box-type steam reforming furnace.

Tubular Fixed-Bed Reactors. Bundles of downflow reactor tubes filled with catalyst and surrounded by heat-transfer media are tubular fixed-bed reactors. Such reactors are used most notably in steam reforming and phthaUc anhydride manufacture. Steam reforming is the reaction of light hydrocarbons, preferably natural gas or naphthas, with steam over a nickel-supported catalyst to form synthesis gas, which is primarily and CO with some CO2 and CH. Additional conversion to the primary products can be obtained by iron oxide-catalyzed water gas shift reactions, but these are carried out ia large-diameter, fixed-bed reactors rather than ia small-diameter tubes (65). The physical arrangement of a multitubular steam reformer ia a box-shaped furnace has been described (1). 

The Phillips Steam Active Reforming (STAR) process catalyticaHy converts isobutane to isobutylene. The reaction is carried out with steam in tubes that are packed with catalyst and located in a furnace. The catalyst is a soHd, particulate noble metal. The presence of steam diluent reduces the partial pressure of the hydrocarbons and hydrogen present, thus shifting the equHibrium conditions for this system toward greater conversions. 

Miscellaneous Fuels A variety of gases have veiy minor market shares. These include reformed gas, oil gases, producer gas, blue water gas, carbureted water gas, coal gas, and blast-furnace gas. The heating values of these gases range from 3.4 to 41 MJ/m (90 to 1100 Btii/ftq. They are produced by pyrolysis, the water gas reaction, or as by-products of pig-iron production. 

Alloy 800 (32% nickel, 20% chromium and 46% iron) is used for furnace equipment such as muffles, trays and radiant tubes and in oil and petrochemical plants as furnace coils for the reforming and pyrolysis of... 

Figure 4.1. A process for producing hydrogen by steam reforming of hydrocarbons (1) reforming furnace (2,3) purification section, (4) shift converter, (5) pressure swing adsorption.

The first step in the production of synthesis gas is to treat natural gas to remove hydrogen sulfide. The purified gas is then mixed with steam and introduced to the first reactor (primary reformer). The reactor is constructed from vertical stainless steel tubes lined in a refractory furnace. The steam to natural gas ratio varies from 4-5 depending on natural gas composition (natural gas may contain ethane and heavier hydrocarbons) and the pressure used. 

The catalytic reforming of CH4 by CO2 was carried out in a conventional fixed bed reactor system. Flow rates of reactants were controlled by mass flow controllers [Bronkhorst HI-TEC Co.]. The reactor, with an inner diameter of 0.007 m, was heated in an electric furnace. The reaction temperatoe was controlled by a PID temperature controller and was monitored by a separated thermocouple placed in the catalyst bed. The effluent gases were analyzed by an online GC [Hewlett Packard Co., HP-6890 Series II] equipped with a thermal conductivity detector (TCD) and carbosphere column (0.0032 m O.D. and 2.5 m length, 80/100 meshes), and identified by a GC/MS [Hewlett Packard Co., 5890/5971] equipped with an HP-1 capillary column (0.0002 m O.D. and 50 m length). 

Traditionally, the steam reforming reactor has a tubular design in which vertical tubes, loaded with catalyst, are surrounded by furnaces to supply the heat required for the strongly endothermic process, see Fig. 8.2. Combustion of natural gas supplies the heat to the tubes. 

Hinchley (1975) discusses the design and operation of waste heat boilers for chemical plant. Both fire tube and water tube boilers are used. A typical arrangement of a water tube boiler on a reformer furnace is shown in Figure 3.12 and a fire tube boiler in Figure 3.13. The application of a waste-heat boiler to recover energy from the reactor exit streams in a nitric acid plant is shown in Figure 3.14. 

In the production of hydrogen by the steam reforming of hydrocarbons, the classic water-gas reaction is used to convert CO in the gases leaving the reforming furnace to hydrogen, in a shift converter. 

---