Dominance test

Table 11.2 shows a comparison of common pill test methods. The best correlation between test method and actnal wear is fonnd when a variety of mechanical forces act npon the fabric dnring testing. For anti-pilling tests of a new article with strange pilling behavionr, the combination of at least two different methods is recommended. They shonld be based on different principles, for example a friction test (e.g. Martindale) and a shock or impact dominated test as RTPT or the shake box test."... 

Whereas in traditional enzymatic analysis spectrophotometric methods dominate, test strips and biospecific electrodes are at the leading edge in the analytical application of immobilized enzymes. This may be expected to continue at least until the mid-90s. 

Li, M., Vo, Q.B., Kowalczyk, R. Efficient heuristic approach to dominance testing in CP-nets. fn Proceedings of 10th international Conference on Autonomous Agents and Multiagent Systems (AAMAS), pp. 353-360 (2011)... 

Laboratory experiments using rodents, or the use of gas analysis, tend to be confused by the dominant variable of fuel—air ratio as well as important effects of burning configuration, heat input, equipment design, and toxicity criteria used, ie, death vs incapacitation, time to death, lethal concentration, etc (154,155). Some comparisons of polyurethane foam combustion toxicity with and without phosphoms flame retardants show no consistent positive or negative effect. Moreover, data from small-scale tests have doubtful relevance to real fine ha2ards. 

Pour-Point Depressants. The pour point of alow viscosity paraffinic oil may be lowered by as much as 30—40°C by adding 1.0% or less of polymethacrylates, polymers formed by Eriedel-Crafts condensation of wax with alkylnaphthalene or phenols, or styrene esters (22). As wax crystallizes out of solution from the Hquid oil as it cools below its normal pour point, the additive molecules appear to adsorb on crystal faces so as to prevent growth of an interlocking wax network which would otherwise immobilize the oil. Pour-point depressants become less effective with nonparaffinic and higher viscosity petroleum oils where high viscosity plays a dominant role in immobilizing the oil in a pour-point test. 

Acute toxicity studies are often dominated by consideration of lethaUty, including calculation of the median lethal dose. By routes other than inhalation, this is expressed as the LD q with 95% confidence limits. For inhalation experiments, it is convenient to calculate the atmospheric concentration of test material producing a 50% mortaUty over a specified period of time, usually 4 h ie, the 4-h LC q. It is desirable to know the nature, time to onset, dose—related severity, and reversibiUty of sublethal toxic effects. 

Ethylene oxide has been shown to produce mutagenic and cytogenic effects in a variety of test systems (226). An increased frequency of chromosomal aberrations in peripheral lymphocytes of monkey exposed to ethylene oxide for 104 weeks has been reported (240). In mice, it is an effective inducer of chromosome breaks leading to dominant-lethal mutations. In addition, ethylene oxide has been shown to induce heritable effects in the heritable translocation test conducted in mice exposed to ethylene oxide by inhalation (241,242). In this study, male mice were exposed to ethylene oxide ranging from 165 to 300 ppm for 6 h per day 5 or 7 days/week for 8.5 weeks. Ethylene oxide has also been shown to bind to proteins (243) as well as to DNA (244). Several studies on ethylene oxide-exposed workers have demonstrated an increased incidence of chromosomal aberrations and sister chromatid exchanges the relevance of such effects to human health evaluation is currendy uncertain. 

Judging from our present knowledge, such a description is far from the whole story. The article of Benderskii and Goldanskii [1992] addressed mostly the vast amount of experimental data accumulated thus far. On the other hand, the major applications of QTST involved gas-phase chemical reactions, where quantum effects were not dominant. All this implies that there is a gap between the possibilities offered by modern quantum theory and the problems of low-temperature chemistry, which apparently are the natural arena for testing this theory. This prompted us to propose a new look at this field, and to consistently describe the theoretical approaches which are adequate even at T = 0. 

In metals, inelastic deformation occurs at the crack tip, yielding a plastic zone. Smith [34] has argued that the elastic stress intensity factor is adequate to describe the crack tip field condition if the inelastic zone is limited in size compared with the near crack tip field, which is then assumed to dominate the crack tip inelastic response. He suggested that the inelastic zone be 1/5 of the size of the near crack tip elastic field (a/10). This restriction is in accordance with the generally accepted limitation on the maximum size of the plastic zone allowed in a valid fracture toughness test [35,36]. For the case of crack propagation, the minimum crack size for which continuum considerations hold should be at least 50 x (r ,J. 

Calculate AS° for ionization of each compound. Comment on the contribution of AH° and AS° to the free energy of ionization. Test the data for linear fiee-energy correlations. Are the linear free-energy correlations dominated by entropy or enthalpy terms ... 

Table 1 contains the metal-to-metal engineering property requirements for Boeing Material Specification (BMS) 5-101, a structural film adhesive for metal to metal and honeycomb sandwich use in areas with normal temperature exposure. The requirements are dominated by shear strength tests. Shear strength is the most critical engineering property for structural adhesives, at least for the simplistic joint analysis that is commonly used for metal-to-metal secondary structure on commercial aircraft. Adhesive Joints are purposefully loaded primarily in shear as opposed to tension or peel modes as adhesives are typically stronger in shear than in Mode I (load normal to the plane of the bond) loading. 

This represents the locus of all the combinations of Ca and Om which cause fatigue failure in a particular number of cycles, N. For plastics the picture is slightly different from that observed in metals. Over the region WX the behaviour is similar in that as the mean stress increases, the stress amplitude must be decreased to cause failure in the same number of cycles. Over the region YZ, however, the mean stress is so large that creep rupture failures are dominant. Point Z may be obtained from creep rupture data at a time equal to that necessary to give (V cycles at the test frequency. It should be realised that, depending on the level of mean stress, different phenomena may be the cause of failure. 

In particular, standard specimens contain a sharp notch so that it is propagation energy rather than initiation energy which is the dominant factor. In general the standard tests are useful for quality control and specification purposes but not... 

---