Cure properties

ASTM D3795, Test Methodfor Thermal Flowj Cure Properties of Thermosetting Plastics by Torque RJ)eometer, Vol. 8.02, ASTM, Philadelphia, Pa., 1993. 

Nonblack fillers such as the precipitated siHcas can reduce both rate and state of cure. The mechanism appears to be one of a competitive reaction between mbber and filler for the zinc oxide activator. Use of materials such as diethylene glycol or triethanolamine prevents this competition thereby maintaining the desired cure characteristics. Neutral fillers such as calcium carbonate (whiting) and clays have Httie or no effect on the cure properties. 

Zinc oxide and stearic acid are used to activate the curing system as well as to preserve cured properties when overcuring, which is curing beyond the point of time and temperature at which maximum properties are obtained. 

In converting ESBR latex to the dry mbber form, coagulating chemicals, such as sodium chloride and sulfuric acid, are used to break the latex emulsion. This solution eventually ends up as plant effluent. The polymer cmmb must also be washed with water to remove excess acid and salts, which can affect the cure properties and ash content of the polymer. The requirements for large amounts of good-quaUty fresh water and the handling of the resultant effluent are of utmost importance in the manufacture of ESBR and directly impact on the plant operating costs. 

Unsaturated polyester resins predominate among fiber-reinforced composite matrices for several reasons. A wide variety of polyesters is available and the composites fabricator must choose the best for a particular appHcation. The choice involves evaluation of fabrication techniques, temperatures at which the resin is to be handled, cure time and temperature desked, and requked cured properties (see Polyesters, unsaturated). 

The sulfonyl chloride group is the cure site for CSM and determines the rate and state of cure along with the compound recipe. It is less stable than the Cl groups and therefore often determines the ceiling temperature for processing. The optimum level of sulfonyl chloride to provide a balance of cured properties and processibiUty is about 2 mol % or 1—1.5 wt % sulfur at 35% Cl. It also undergoes normal acid chloride reactions with amines, alcohols, etc, to make useful derivatives (17). 

In Table 3 a few examples are given of typical EPDM recipes with pertinent cured properties. 

These three cure systems have in common the need for a two-step cure cycle to generate the best cured properties. The first step is the appHcation of heat and pressure in a mold to shape the article (press cure). The second step is a high temperature oven cycle at atmospheric pressure to obtain the final cured properties. 

Vmulsifier Type. The manufacturers of NBR use a variety of emulsifiers (most commonly anionic) for the emulsion polymerisation of nitrile mbber. When the latex is coagulated and dried, some of the emulsifier and coagulant remains with the mbber and affects the properties attained with the mbber compound. Water resistance is one property ia particular that is dependent on the type and amount of residual emulsifier. Residual emulsifer also affects the cure properties and mold fouling characteristics of the mbber. 

Monofunctional aliphatic glycidyl ethers, eg, based on / -butanol or mixed Cg—alcohols, are used exclusively as reactive diluents to reduce viscosities of epoxy resin systems. Some loss of desirable cured properties results from the lowered functionality of the systems. 

Cohesive strength of these adhesives can be modified by blending butyl rubber and polyisobutylene. Higher strength is obtained by using high molecular weight PIB or butyl rubber. On the other hand, blends of butyl rubber or PIB with chlorinated butyl rubber show improved cure properties. 

Loctite has developed several acrylate adhesives that can be used as EB-curable adhesives [12]. Some of the resins were cured and tested for EB curing properties... 

Determination of mechanical properties like tensile strength, tear strength, modulus, and elongation at break are the most common methods adopted to determine the cured properties of short fiber-mbber composites. Murty and De [133] discussed the technical properties of short fiber-mbber composites whereas Abrate [8] reviewed the mechanism of short fiber reinforcement of mbber. Fiber concentration in the matrix plays an important role in the optimization of the required... 

The curing properties were determined with the aid of a rubber process analyzer (RPA 2000, Alpha Technologies) at a temperature of 160°C. The compounds were cured in a laboratory press at 160°C and 100 bar at a time corresponding to the fgo of the specific compound. 

The final physical properties of thermoset polymers depend primarily on the network structure that is developed during cure. Development of improved thermosets has been hampered by the lack of quantitative relationships between polymer variables and final physical properties. The development of a mathematical relationship between formulation and final cure properties is a formidable task requiring detailed characterization of the polymer components, an understanding of the cure chemistry and a model of the cure kinetics, determination of cure process variables (air temperature, heat transfer etc.), a relationship between cure chemistry and network structure, and the existence of a network structure parameter that correlates with physical properties. The lack of availability of easy-to-use network structure models which are applicable to the complex crosslinking systems typical of "real-world" thermosets makes it difficult to develop such correlations. 

Lightfastness in rubber, which meets almost all requirements, is accompanied by good curing properties and migration resistance. The resulting pigmented articles are very resistant to water and detergent solutions. 

Pearce, E.M., Mijovic, J. Characterization-Curing-Property Studies of HBRF S5A Resin Formulations (1985) NASA-Ames Research Center... 

In process design, the main objective is to optimize the cured properties of the finished product. To that end, the following conditions have to be established and quantified ... 

Table 13 Cure properties of SBR compounds with different sulfur samples ...

Many of these so-called natural products were first used without any knowledge of their chemical composition. As organic chemistry developed, though, chemists learned how to work out the structures of the compounds in natural products. The disease-curing properties of limes and other citrus fruits, for example, were known for centuries but the chemical structure of vitamin C, the active ingredient, was not determined until 1933. Today there is a revival of interest in folk remedies, and a large effort is being made to identify medicinally important chemical compounds found in plants. 

---