Corrosion concept

Primarily connected to corrosion concepts, Pourbaix diagrams may be used within the scope of prediction and understanding of the thermodynamic stability of materials under various conditions. Park and Barber [25] have shown this relevance in examining the thermodynamic stabilities of semiconductor binary compounds such as CdS, CdSe, CdTe, and GaP, in relation to their flat band potentials and under conditions related to photoelectrochemical cell performance with different redox couples in solution. 

ECORR, computer-aided learning package designed to assist in training students in corrosion concepts... 

This chapter is aimed to illustrate the most accepted theories concerning corrosion protection mechanisms of conducting polymers and their composites, reporting a wide review of literature on these topics. Firstly, a brief revision of some basic corrosion concepts, as well as of the corrosion prevention and testing methods, is given. 

Bagnulo, L. H., (1984). Cold laminar galvanizing A new anti-corrosion concept. Pipe Line Ind., March, pp. 25-21. 

The selection of materials to be used in design dictates a basic understanding of the behavior of materials and the principles that govern such behavior. If proper design of suitable materials of construction is incorporated, the eqiiipment should deteriorate at a uniform and anticipated gradual rate, which will allow scheduled maintenance or replacement at regular inteivals. If localized forms of corrosion are characteristic of the combination of materials and environment, the materials engineer should still be able to predict the probable life of equipment, or devise an appropriate inspection schedule to preclude unexpected failures. The concepts of predictive, or at least preventive, maintenance are minimum requirements to proper materials selection. This approach to maintenance is certainly intended to minimize the possibility of unscheduled production shutdowns because of corrosion failures, with their attendant possible financial losses, hazard to personnel and equipment, and resultant environmental pollution. 

The use of impedance electrochemical techniques to study corrosion mechanisms and to determine corrosion rates is an emerging technology. Elec trode impedance measurements have not been widely used, largely because of the sophisticated electrical equipment required to make these measurements. Recent advantages in micro-elec tronics and computers has moved this technique almost overnight from being an academic experimental investigation of the concept itself to one of shelf-item commercial hardware and computer software, available to industrial corrosion laboratories. 

The Steam Injection Cycle Steam injection has been used in reciprocating engines and gas turbines for a number of years. This cycle may be an answer to the present concern with pollution and higher efficiency. Corrosion problems are the major hurdle in such a system. The concept is simple and straightforward Steam is injected into the compressor discharge air and increases the mass flow rate... 

The concept of the corrosion process, derived from the Latin corrodere (to eat away, to destroy), first appeared in the Philosophical Transactions in 1667 [2]. It was discussed in a German translation from the French on the manufacture of white lead in 1785 and was mentioned in 1836 in the translation of an English paper by Davy on the cathodic protection of iron in seawater [3]. However, almost until the present day, the term was used indiscriminately for corrosion reaction, corrosion effects, and corrosion damage. Only in DIN 50900, Part I, were these terms distinguished and defined [4] (see Section 2.1). 

Fundamentals and Concepts of Corrosion and Electrochemical Corrosion Protection... 

Electrochemical corrosion is understood to include all corrosion processes that can be influenced electrically. This is the case for all the types of corrosion described in this handbook and means that data on corrosion velocities (e.g., removal rate, penetration rate in pitting corrosion, or rate of pit formation, time to failure of stressed specimens in stress corrosion) are dependent on the potential U [5]. Potential can be altered by chemical action (influence of a redox system) or by electrical factors (electric currents), thereby reducing or enhancing the corrosion. Thus exact knowledge of the dependence of corrosion on potential is the basic hypothesis for the concept of electrochemical corrosion protection processes. 

Corrosion likelihood describes the expected corrosion rates or the expected extent of corrosion effects over a planned useful life [14]. Accurate predictions of corrosion rates are not possible, due to the incomplete knowledge of the parameters of the system and, most of all, to the stochastic nature of local corrosion. Figure 4-3 gives schematic information on the different states of corrosion of extended objects (e.g., buried pipelines) according to the concepts in Ref. 15. The arrows represent the current densities of the anode and cathode partial reactions at a particular instant. It must be assumed that two narrowly separated arrows interchange with each other periodically in such a way that they exist at both fracture locations for the same amount of time. The result is a continuous corrosion attack along the surface. 

Since the reliability of gas turbines in the power industry has been lower than desired in recent years because of hot-corrosion problems, techniques have been developed to detect and control the parameters that cause these problems. By monitoring the water content and corrosive contaminant in the fuel line, any changes in fuel quality can be noted and corrective measures initiated. The concept here is that Na contaminants in the fuel are caused from external sources such as seawater thus, by monitoring water content, Na content is automatically being monitored. This on-line technique is adequate for lighter distillate fuels. For heavier fuels, a more complete analysis of the fuel should be carried out at least once a month using the batch-type system. The data should be input directly to the computer. The water and corrosion detecting systems also operate in conjunction with the batch analysis for the heavier fuels. 

Many factors and conditions affect the tendency of metals to corrode. Once the right conditions and all the components are present, corrosion may proceed in one or more forms. Before considering the aforementioned points, it is necessary to consider the concepts of polarization and passivity. 

Figure 4-419 illustrates the concept of corrosion process under concentration polarization control. Considering hydrogen evolution at the cathode, reduction rate of hydrogen ions is dependent on the rate of diffusion of hydrogen ions to the metal surface. Concentration polarization therefore is a controlling factor when reducible species are in low concentrations (e.g., dilute acids). 

In the case of non-metallic materials, the term corrosion invariably refers to their-deterioration from chemical causes, but a similar concept is not necessarily applicable to metals. Many authorities consider that the term metallic corrosion embraces all interactions of a metal or alloy (solid or liquid) with its environment, irrespective of whether this is deliberate and beneficial or adventitious and deleterious. Thus this definition of corrosion, which for convenience will be referred to as the transformation definition. 

On the other hand, corrosion has been defined as the undesirable deterioration of a metal or alloy, i.e. an interaction of the metal with its environment that adversely affects those properties of the metal that are to be preserved. This definition —which will be referred to as the deterioration definition —is also applicable to non-metallic materials such as glass, concrete, etc. and embodies the concept that corrosion is always deleterious. However, the restriction of the definition to undesirable chemical reactions of a metal results in anomalies which will become apparent from a consideration of the following examples. 

Although the mechanism of corrosion is highly complex the actual control of the majority of corrosion reactions can be effected by the application of relatively simple concepts. Indeed, the Committee on Corrosion and Protection concluded that better dissemination of existing knowledge was the most important single factor that would be instrumental in decreasing the enormous cost of corrosion in the U.K. 

It should be noted that Fig. 1.15 (top) is based entirely on thermodynamic data and is therefore correctly described as an equilibrium diagram, since it shows the phases (nature and activity) that exist at equilibrium. However, the concepts implicit in the terms corrosion, immunity and passivity lie outside the realm of thermodynamics, and, for example, passivity involves both thermodynamic and kinetic concepts it follows that Fig. 1.15 (bottom) cannot be regarded as a true equilibrium diagram, although it is based on one that has been constructed entirely from thermodynamic data. 

---