Anti-corrosion

Corrosion and anti-wear protection Anti-corrosion and anti-wear power High viscosity at high shear rates... 

Protection of lubricated members Viscosity selection Anti-wear power Anti-corrosion power... 

For gear trains Protection from seizing and rapid wear Extreme-pressure and anti-wear properties Resistance to oxidation Thermal stability High viscosity Low pour point Anti-foaming properties Anti-corrosion properties... 

The second detergent function is to prevent formation of varnishes that come from polymerization of deposits on hot surfaces of the cylinder and the piston. Finally, by adsorption on metallic surfaces, these compounds have anti-corrosion effects. 

An MS tank with a wall thickness of 3 mm is adequate, otherwise the thickness can be similar to that for the degreasing lank but without the healing arrangement. It may also be coated with an anti-corrosive paint to enhance its life. 

To rinse, wash the surface in clear, continuous running water to remove all traces of soluble salts which may cause blistering on the surface. The tank can be similar to the phosphating lank. It may, however, be coated with an anti-corrosive paint to extend its life. 

This is similar to that for phosphating. It may, however, be coaled with an anti-corrosive paint to extend its life. 

High-alloy ("stainless") 1 Cr 2 Ni Fe -r 0.1 C 0.5 Mn High-temperature or anti-corrosion uses chemical or... 

Firmenschrift, Bergsoe Anti Corrosion, Landskrona (Schweden) 1987. 

Plant/process emissions Anti-corrosion coatings heat shields, extractors... 

Barnbrook, G., The concrete slab-a base for resin flooring, paper presented at the Symposium on Resin for Industrial Problem Areas. Flooring and Anti-Corrosion Application, organized by the Federation of Resin Formulators and Applicators Ltd, London, November (1980). 

Bacterial examination could be used to confirm the presence of (and perhaps identify) the species. Where soluble oil is being degraded, or where a noticeable loss of anti-corrosion properties has been detected, a check on the pH (alkalinity/acidity) of the system would be advantageous. 

Paints are complex formulations of polymeric binders with additives including anti-corrosion pigments, colors, plasticizers, ultraviolet absorbers, flame-retardant chemicals, etc. Almost all binders are organic materials such as resins based on epoxy, polyurethanes, alkyds, esters, chlorinated rubber and acrylics. The common inorganic binder is the silicate used in inorganic zinc silicate primer for steel. Specific formulations are available for application to aluminum and for galvanized steel substrates. 

The selection of an anti-corrosion paint-coating scheme should be undertaken by a qualified expert. 

Despite the introduction of new, improved methods of refining it has been necessary to enhance the performance of lubricants by the use of additives, either to reinforce existing qualities or to confer additional properties. Once additives were regarded with some suspicion —an oil that needed an additive was necessarily an inferior oil today they are an accepted feature of lubricants. Almost all quality lubricants on sale today contain one or more additives. An enormous range of additives are available for use in lubricants " , some produced by the oil companies and others provided by specialist manufacturers. Additives are usually named after their particular function, but many additives are multifunctional. Thus, an anti-wear additive may also protect a surface against corrosion. The main types of additives that can enhance the anti-corrosion behaviour of lubricants are listed in Table 2.22. 

Table 2.22 Additives that can enhance the anti-corrosion behaviour of lubricants...

K Julyan Day, FICorr, FTSC, MBIM Anti-Corrosion Consultant... 

A recent NACE publication devoted entirely to the economic aspects of corrosion control contains several worked examples applicable to a number of industries. These examples serve to illustrate that anti-corrosion procedure and materials should be selected on economic grounds, and not solely on performance grounds. In presenting a proposal to management. 

Therefore, the use of welding as a method of fabrication may modify the corrosion behaviour of an engineering structure, and this may be further aggravated by removal of protective systems applied before welding, whilst at the same time the use of such anti-corrosion coatings may lead to difficulties in obtaining satisfactorily welded joints ... 

---