Copper growth

A.M. Bittner, J. Wintterlin, G. Ertl, Strain relief during metal-on-metal electrodeposition A scanning tunneling microscopy study of copper growth on Pt(lOO). Surf. Sci. 376, 267-278, 1996. 

On the other hand, the knowledge of surface energies and interfacial energies is not sufficient to understand the growth dynamics at finite temperature. In their study of copper growth on the 0-terminated polar ZnO(OOOl) face, Ernst et al. (1993) have, for example, stressed the importance of the evaporation energy of copper atoms from kinks located at... 

Consider the plating of copper from the process shown in Figure 9.6. Calculate the minimum electrode potential to achieve copper growth. The aqueous solution has the following composition 0.07 m CUSO4 and pH = 1. You may assume you have an ideal solution. 

Studies have been made on the rate of growth of oxide films on different crystal faces of a metal using ellipsometric methods. The rate was indeed different for (100), (101), (110), and (311) faces of copper [162] moreover, the film on a (311) surface was anisotropic in that its apparent thickness varied with the angle of rotation about the film normal. 

Isobutyl alcohol [78-83-1] forms a substantial fraction of the butanols produced by higher alcohol synthesis over modified copper—zinc oxide-based catalysts. Conceivably, separation of this alcohol and dehydration affords an alternative route to isobutjiene [115-11 -7] for methyl /-butyl ether [1624-04-4] (MTBE) production. MTBE is a rapidly growing constituent of reformulated gasoline, but its growth is likely to be limited by available suppHes of isobutylene. Thus higher alcohol synthesis provides a process capable of supplying all of the raw materials required for manufacture of this key fuel oxygenate (24) (see Ethers). 

Wrought or extmded lead—teUurium (0.035—0.10 wt %) aUoys produce extremely fine grains. The binary aUoy is, however, susceptible to recrysta11i2ation. The addition of copper or sUver reduces grain growth and retains the fine grain si2e. Because teUurium is a poison for sealed lead—acid batteries, the teUurium content of lead and lead aUoys used for such purposes is usuaUy restricted to less than 1 ppm. 

The matte can be treated in different ways, depending on the copper content and on the desired product. In some cases, the copper content of the Bessemer matte is low enough to allow the material to be cast directly into sulfide anodes for electrolytic refining. Usually it is necessary first to separate the nickel and copper sulfides. The copper—nickel matte is cooled slowly for ca 4 d to faciUtate grain growth of mineral crystals of copper sulfide, nickel—sulfide, and a nickel—copper alloy. This matte is pulverized, the nickel and copper sulfides isolated by flotation, and the alloy extracted magnetically and refined electrolyticaHy. The nickel sulfide is cast into anodes for electrolysis or, more commonly, is roasted to nickel oxide and further reduced to metal for refining by electrolysis or by the carbonyl method. Alternatively, the nickel sulfide may be roasted to provide a nickel oxide sinter that is suitable for direct use by the steel industry. 

Plants can also be pests that need to be controlled, particulady noxious weeds infesting food crops. Prior to 1900, inorganic compounds such as sulfuric acid, copper nitrate, sodium nitrate, ammonium sulfate, and potassium salts were used to selectively control mustards and other broadleaved weeds in cereal grains. By the early 1900s, Kainite and calcium cyanamid were also used in monocotyledenous crops, as well as iron sulfate, copper sulfate, and sodium arsenate. Prom 1915 to 1925, acid arsenical sprays, carbon bisulfate, sodium chlorate, and others were introduced for weed control use. Total or nonselective herbicides kill all vegetation, whereas selective compounds control weeds without adversely affecting the growth of the crop (see Herbicides). 

Antimicrobial agents are used where there is a need to inhibit bacterial and fungal growth. The additives can consist of copper, germanium, zinc and zinc compounds, metal oxides or sulfides, metal zeofltes, as well as silver and copper oxide-coated inorganic core particles (154—159) (see Industrial ANTIMICROBIAL AGENTS). 

Additional areas for growth are expected to be ia copper leaching, caprolactam, pulp and paper, methyl methacrylate, and batteries (144). 

Plant and Animal Nutrient. Copper is one of seven micronutrients that has been identified as essential to the proper growth of plants (87). Cereal crops are by far the most affected by copper deficiency (see Wheat and other cereal grains). Greenhouse studies have shown yield increases from 38% to over 500% for wheat, barley, and oats (88) using copper supplementation. A tenfold increase in the yield of oats was reported in France (89). Symptoms of copper deficiency vary depending on species, but often it is accompanied by withering or chlorosis in the leaves that is not ammenable to iron supplementation. In high concentrations, particularly in low pH sods, copper can be toxic to plants. 

---