Continuous emulsion polymerization kinetics

Continuous emulsion polymerization processes are presently employed for large scale production of synthetic rubber latexes. Owing to the recent growth of the market for polymers in latex form, this process is becoming more and more important also in the production of a number of other synthetic latexes, and hence, the necessity of the knowledge of continuous emulsion polymerization kinetics has recently increased. Nevertheless/ the study of continuous emulsion polymerization kinetics hasf to datef received comparatively scant attention in contrast to batch kinetics/ and very little published work is available at present/ especially as to the reactor optimization of continuous emulsion polymerization processes. For the theoretical optimization of continuous emulsion polymerization reactors/ it is desirable to understand the kinetics of emulsion polymerization as deeply and quantitatively as possible. 

Gerrens and Kuchner [337] investigated the continuous emulsion polymerization kinetics in a cascade of three CSTRs, and with St and MA as monomers with different solubilities in water. They showed that the experimental results obtained with St agreed with the predictions from the Gershberg and Longfield... 

Continuous emulsion polymerization systems are studied to elucidate reaction mechanisms and to generate the knowledge necessary for the development of commercial continuous processes. Problems encountered with the development of continuous reactor systems and some of the ways of dealing with these problems will be discussed in this paper. Those interested in more detailed information on chemical mechanisms and theoretical models should consult the review papers by Ugelstad and Hansen (1), (kinetics and mechanisms) and by Poehlein and Dougherty (2, (continuous emulsion polymerization). 

Note References 1. and 2. contain extensive bibliographies on emulsion polymerization kinetics and continuous emulsion polymerization respectively. 

The present review paper, therefore, refers firstly to the particle formation mechanism in emulsion polymerization, the complete understanding of which is indispensable for establishing a correct kinetic model, and then, deals with the present subject, that is, what type of reactor and operating conditions are the most suitable for a continuous emulsion polymerization process from the standpoint of increasing the volume efficiency and the stability of the reactors. 

Although the early literature described the application of a tubular reactor for the production of SBR latexes(1), the standard continuous emulsion polymerization processes for SBR polymerization still consist of continuous stirred tank reactors(CSTR s) and all of the recipe ingredients are normally fed into the first reactor and a latex is removed from the last one, as shown in Figure 1. However, it is doubtful whether this conventional reactor combination and operation method is the most efficient in continuous emulsion polymerization. As is well known, the kinetic behavior of continuous emulsion polymerization differs very much according to the kind of monomers. In this paper, therefore, the discussion about the present subject will be advanced using the... 

Our final goal in the present paper is to devise an optimal type of the first stage reactor and its operation method which will maximize the number of polymer particles produced in continuous emulsion polymerization. For this purpose, we need a mathematical reaction model which explains particle formation and other kinetic behavior of continuous emulsion polymerization of styrene. 

Let us determine the value of e by comparing the transient kinetic behavior of monomer conversion in continuous emulsion polymerization of styrene with the model prediction by the Nomura and Harada model. It is reported in the literature that sustained... 

The use of a precision digital density meter as supplied by Mettler Instruments (Anton Paar, Ag.) appeared attractive. Few references on using density measurements to follow polymerization or other reactions appear in the literature. Poehlein and Dougherty (2) mentioned, without elaboration, the occasional use of y-ray density meters to measure conversion for control purposes in continuous emulsion polymerization. Braun and Disselhoff (3) utilized an instrument by Anton Paar, Ag. but only in a very limited fashion. More recently Rentsch and Schultz(4) also utilized an instrument by Anton Paar, Ag. for the continuous density measurement of the cationic polymerization of 1,3,6,9-tetraoxacycloundecane. Ray(5) has used a newer model Paar digital density meter to monitor emulsion polymerization in a continuous stirred tank reactor train. Trathnigg(6, 7) quite recently considered the solution polymerization of styrene in tetrahydrofuran and discusses the effect of mixing on the reliability of the conversion data calculated. Two other references by Russian authors(8,9) are known citing kinetic measurements by the density method but their procedures do not fulfill the above stated requirements. 

Oscillations in the number of polymer particles, the monomer conversion, and the molecular weight of the polymers produced, which are mainly observed in a CSTR, have attracted considerable interest. Therefore, many experimental and theoretical studies dealing with these oscillations have been published [328]. Recently,Nomura et al. [340] conducted an extensive experimental study on the oscillatory behavior of the continuous emulsion polymerization of VAc in a single CSTR. Several researchers have proposed mathematical models that quantitatively describe complete kinetics, including oscillatory behavior [341-343]. Tauer and Muller [344] proposed a simple mathematical model for the continuous emulsion polymerization of VCl to explain the sustained oscillations observed. Their numerical analysis showed that the oscillations depend on the rates of particle growth and coalescence. However, it still seems to be difficult to quantitatively describe the kinetic behavior (including oscillations) of the continuous emulsion polymerization of monomers, especially those with relatively high solubility in water. This is mainly because the kinetics and mech-... 

This can be explained by the fact that the flow in the CCTVFR became closer to plug flow as the Taylor number was dropped closer to. Therefore, the steady-state particle number and the steady-state monomer conversion could be arbitrarily varied by simply varying the rotational speed of the inner cylinder. Moreover, no oscillations were observed, and the rotational speed of the inner cylinder could be kept low, so that the possibility of shear-induced coagulation could be decreased. Therefore, a CCTVFR with these characteristics is considered to be highly suitable as a pre-reactor for a continuous emulsion polymerization process. In the case of the continuous emulsion polymerization of VAc carried out with the same CCTVFR, however, the situation was quite different [365]. Oscillations in monomer conversion were observed, and almost no appreciable increase in steady-state monomer conversion occurred even when the rotational speed of the inner cylinder was decreased to a value close to. Why the kinetic behavior with VAc is so different to that with St cannot be explained at present. 

Polystyrene can be easily prepared by emulsion or suspension techniques. Harkins (1 ), Smith and Ewart(2) and Garden ( ) have described the mechanisms of emulsTon polymerization in batch reactors, and the results have been extended to a series of continuous stirred tank reactors (CSTR)( o Much information on continuous emulsion reactors Ts documented in the patent literature, with such innovations as use of a seed latex (5), use of pulsatile flow to reduce plugging of the tube ( ), and turbulent flow to reduce plugging (7 ). Feldon (8) discusses the tubular polymerization of SBR rubber wTth laminar flow (at Reynolds numbers of 660). There have been recent studies on continuous stirred tank reactors utilizing Smith-Ewart kinetics in a single CSTR ( ) as well as predictions of particle size distribution (10). Continuous tubular reactors have been examined for non-polymeric reactions (1 1 ) and polymeric reactions (12.1 31 The objective of this study was to develop a model for the continuous emulsion polymerization of styrene in a tubular reactor, and to verify the model with experimental data. 

The objective was to develop a model for continuous emulsion polymerization of styrene in tubular reactors which predicts the radial and axial profiles of temperature and concentration, and to verify the model using a 240 ft. long, 1/2 in. OD Stainless Steel Tubular reactor. The mathematical model (solved by numerical techniques on a digital computer and based on Smith-Ewart kinetics) accurately predicts the experimental conversion, except at low conversions. Hiqh soap level (1.0%) and low temperature (less than 70°C) permitted the reactor to perform without plugging, giving a uniform latex of 30% solids and up to 90% conversion, with a particle size of about 1000 K and a molecular weight of about 2 X 10 . 

Types of Reactor Processes Batch Reactors Semibatch Reactors Continuous Reactors Emulsion Polymerization Kinetics Other Preparation Methods... 

D. B. Getshberg and J. E. Longfield, Kinetics of continuous emulsion polymerization, Paper 10, 45th AIChE Meeting, New York, 1961... 

Gershberg, D.B. Longfield, J.E. Kinetics of the Continuous Emulsion Polymerization 1961, 54 AIChE Meeting, New York. 

The batch emulsion polymerization is commonly used in the laboratory to study the reaction mechanisms, to develop new latex products and to obtain kinetic data for the process development and the reactor scale-up. Most of the commercial latex products are manufactured by semibatch or continuous reaction systems due to the very exothermic nature of the free radical polymerization and the rather limited heat transfer capacity in large-scale reactors. One major difference among the above reported polymerization processes is the residence time distribution of the growing particles within the reactor. The broadness of the residence time distribution in decreasing order is continuous>semibatch>batch. As a consequence, the broadness of the resultant particle size distribution in decreasing order is continuous>semibatch>batch, and the rate of polymerization generally follows the trend batch>semibatch>continuous. Furthermore, the versatile semibatch and continuous emulsion polymerization processes offer the operational flexibility to produce latex products with controlled polymer composition and particle morphology. This may have an important influence on the application properties of latex products [270]. 

The primary purpose of this paper is to provide information on continuous emulsion polymerization reactors that will help the reader to make rational decisions on the possible use of such reactors in the commercial production of polymer latexes. A second purpose is to demonstrate the utility of continuous reactors as a tool for studying reaction kinetics. 

One unique but normally undesirable feature of continuous emulsion polymerization carried out in a stirred tank reactor is reactor dynamics. For example, sustained oscillations (limit cycles) in the number of latex particles per unit volume of water, monomer conversion, and concentration of free surfactant have been observed in continuous emulsion polymerization systems operated at isothermal conditions [52-55], as illustrated in Figure 7.4a. Particle nucleation phenomena and gel effect are primarily responsible for the observed reactor instabilities. Several mathematical models that quantitatively predict the reaction kinetics (including the reactor dynamics) involved in continuous emulsion polymerization can be found in references 56-58. Tauer and Muller [59] developed a kinetic model for the emulsion polymerization of vinyl chloride in a continuous stirred tank reactor. The results show that the sustained oscillations depend on the rates of particle growth and coalescence. Furthermore, multiple steady states have been experienced in continuous emulsion polymerization carried out in a stirred tank reactor, and this phenomenon is attributed to the gel effect [60,61]. All these factors inevitably result in severe problems of process control and product quality. 

It is not straightforward to successfully manufacture a particular latex product, which is generally developed in a laboratory batch or semibatch reactor, in a commercial continuous emulsion polymerization system (e.g., a continuous stirred tank reactor). This is simply because the characteristics of continuous stirred tank reactors are dramatically different from those of batch and semibatch reactors. As a consequence, the particle nucleation process and kinetics experienced in batch or semibatch emulsion polymerization systems cannot be directly applied to continuous systems consisting of stirred tank reactors. 

The continuous bulk polymerization of methyl methacrylate was used as an example in Section 5.2. A stirred bulk polymerization like that used for styrene (Section 5.4) could be adapted for methyl methacrylate. A suspension process for poly(methyl methacrylate) was described in Section 5.4. The polymerization of ethyl acrylate most often is carried out in emulsion. A process such as that used for vinyl acetate is suitable (Section 16.4). Like vinyl acetate, the monomer is slightly water soluble, so true emulsion polymerization kinetics are not followed. That is, there is initiation of monomer dissolved in water in addition to that dissolved in growing polymer particles. Ethyl acrylate is distinguished by its rapid rate of propagation. Initiation of a 20% monomer emulsion at room temperature by the redox couple persulfate-metabisulflte can result in over 95% conversion in less than a minute. As with vinyl acetate polymerization, a continuous addition of monomer at a rate commensurate with the heat transfer capacity of the reactor is necessary in order to control the temperature. 

---