Containment precautions

No live virus should be removed from this area unless enclosed in a tightly closed container. Precautions should be taken to ensure that the outsides of all vessels are free of virus particles. 

Table I summarizes the practices necessary for four biosafety levels of containment of plants. Biosafety level 1 would be similar to a standard greenhouse, with the containment precautions becoming more strict at higher levels. The IBC would recommend the appropriate containment level for each experiment and will be responsible for assuring that the principal investigator adheres to the approved practices for that project.

Any process heat plant design implies piping through the containment to connect the reactor vessel with the chemical plant. The fracture of a pipe could result in the accumulation of a flammable gas mixture in the containment. Precautions must be taken to minimize the risk of a fire or gas explosion such as avoidance of explosive gas ingress, proper detection devices, inerting, sufficient safety distances, appropriate layout of secondary coolant boundary, explosion-proofed wall, plant isolation valve. For the PNP-500, the use of two concentric pipes for the process gas carrying lines were recommended. Alternatives are concrete channels around the gas lines or inerting of the containment [10]. 

In some cases of pilot scale filtration, entire units have been enclosed as a secondary containment precaution (see Chapter 8). A recent commercial development is the MBR-Sultzer dynamic filter which is available in three sizes. Dynamic filtration is the same as cross flow filtration with little or no recirculation. The cross flow effect is derived from the spinning of the inner surface filter. This type of filter is more efficient, has a lower pump rate and a much higher linear velocity across the filter surface, than conventional cross flow filtration units. There is also little or no damaging effect on sensitive cells. The medium size has the same capacity as the Westfalia SA-7 separator. Van Hemert and Tiesjema concluded that the dynamic filter is suitable for work requiring strict aseptic and primary containment conditions. The use of a double mechanical seal on the rotating shaft could offer a higher degree of containment if required. 

When ethanoi is present, the risk of separation is much less than with methanol. Nevertheless, the ethanol should be relatively anhydrous (less than 3000 ppm water) moreover, if a fuel containing ethanol comes in contact with a water layer, a migration of ethanol toward the water is observed creating a fuel quality problem manifested by lower octane number and an environmental quality problem in that the water will need to be treated. Distribution of ethanol-based fuels requires extra precaution to ensure dryness in distribution systems. 

Dissolve 4 5 ml. of aniline in a mixture of 10 ml. of concentrated hydrochloric acid and 20 ml. of water cool the solution to 5°, and diazotise by the addition of 4 g. of sodium nitrite dissolved in 20 ml, of water, observing the usual precautions given on page 181. Dissolve 7 g. of 2-naphthol in 60 ml. of 10% sodium hydroxide solution contained in a 200 ml. beaker, and cool this solution to 5 by external cooling, aided by the direct addition of about 20-30 g. of crushed ice. Now add the diazotised solution very slowly to the naphthol solution, keeping the latter well stirred meanwhile the mixed solutions immediately develop a deep red colour, and the benzeneazonaphthol should... 

This tube is connected %vith rubber tubing of about 6 mm. bore to the carbon dioxide Kipp, via a wash-bottle containing sodium carbonate solution (to remove any dilute hydrochloric acid spray). It is very important, when the apparatus is in use, that there should be no constriction or bend in the rubber tube between the tap C and the wash-bottle. If these precautions are taken, a slow, e en, and easily controlled flow of gas can be obtained. 

Hydrogen chloride. Method 1 from concentrated sulphuric acid and fused ammonium chloride). The most convenient procedure is to allow concentrated sulphuric acid to react with lumps of fused ammonium chloride in a Kipp s apparatus. The gas may be dried by passage through a wash bottle containing concentrated sulphuric acid the latter should be followed by an empty wash bottle or flask as a precaution against sucking back of the contents of the reaction vessel. 

The conversion of a diazo ketone to an acid amide may be accomplished by treating a warm solution in dioxan with 10-28 per cent, aqueous ammonia solution containing a small amount of silver nitrate solution, after which the mixture is heated at 60°-70° for some time. Precautions should be taken (by use of a. safety glass shield) when heating mixtures containing ammoniacal silver nitrate. 

Three important precautions are needed when working with pipets and volumetric flasks. First, the volume delivered by a pipet or contained by a volumetric flask assumes that the glassware is clean. Dirt and grease on the inner glass surface prevents liquids from draining evenly, leaving droplets of the liquid on the container s walls. For a pipet this means that the delivered volume is less than the calibrated volume, whereas drops of liquid above the calibration mark mean that a volumetric flask contains more than its calibrated volume. Commercially available cleaning solutions can be used to clean pipets and volumetric flasks. 

The effluent from a GC column is already in the gas phase and needs only to be mixed with argon makeup gas before passage into the flame. Precautions need to be taken to divert temporarily the GC flow when the first solvent peak emerges because it contains far too much material for the plasma to withstand. 

Formic acid is combustible (flash point = 69° C), but the explosive ha2ard is considered slight. The decomposition to CO requires appropriate precautions to be taken when entering tanks or other confined spaces that have contained the acid. 

Workers in the metals treatment industry are exposed to fumes, dusts, and mists containing metals and metal compounds, as well as to various chemicals from sources such as grinding wheels and lubricants. Exposure can be by inhalation, ingestion, or skin contact. Historically, metal toxicology was concerned with overt effects such as abdominal coHc from lead toxicity. Because of the occupational health and safety standards of the 1990s such effects are rare. Subtie, chronic, or long-term effects of metals treatment exposure are under study. An index to safety precautions for various metal treatment processes is available (6). As additional information is gained, standards are adjusted. 

---