Mixed conductor.

TR - transition region nearly pure (97-100%) ionic conductor mixed with second compound K - specific conductivity ohm cm D.C. - dielectric constant r - viscosity, centipoises ... 

Electronic conductors Semiconductors Ionic conductors Mixed conductors Ferrimagnetics Thermal conductors Thermal insulators Chromophores Translucent materials Nonlinear optics Photovoltaics Transparent conductors Active materials Inert materials Biocompatibles... 

Typical electrodes contain finely dispersed catalyst(s) on a high-area oxidation-resistant form of carbon conductor mixed with PTFE or other wet-proofing material and a metal foil or screen that serves as a material carrier and electronic charge collector. The carbon/PTFE mix-mre containing a removable solvent is applied to the carrier and dried to form a porous strucmre that allows O2 access to the liquid/solid interface. Both liquid and gas must be able to penetrate the solid electrode structure for the reaction to proceed at practical rates. 

Chemical properties of deposited monolayers have been studied in various ways. The degree of ionization of a substituted coumarin film deposited on quartz was determined as a function of the pH of a solution in contact with the film, from which comparison with Gouy-Chapman theory (see Section V-2) could be made [151]. Several studies have been made of the UV-induced polymerization of monolayers (as well as of multilayers) of diacetylene amphiphiles (see Refs. 168, 169). Excitation energy transfer has been observed in a mixed monolayer of donor and acceptor molecules in stearic acid [170]. Electrical properties have been of interest, particularly the possibility that a suitably asymmetric film might be a unidirectional conductor, that is, a rectifier (see Refs. 171, 172). Optical properties of interest include the ability to make planar optical waveguides of thick LB films [173, 174]. 

The anode material in SOF(7s is a cermet (rnetal/cerarnic composite material) of 30 to 40 percent nickel in zirconia, and the cathode is lanthanum rnanganite doped with calcium oxide or strontium oxide. Both of these materials are porous and mixed ionic/electronic conductors. The bipolar separator typically is doped lanthanum chromite, but a metal can be used in cells operating below 1073 K (1472°F). The bipolar plate materials are dense and electronically conductive. 

Sample conductivity Conductors and semiconductors direct analysis insulators (>10 (ohm-cm) ) pulverize and mix with a conductor... 

A quite different approach was introduced in the early 1980s [44-46], in which a dense solid electrode is fabricated which has a composite microstructure in which particles of the reactant phase are finely dispersed within a solid, electronically conducting matrix in which the electroactive species is also mobile. There is thus a large internal reactant/mixed-conductor matrix interfacial area. The electroactive species is transported through the solid matrix to this interfacial region, where it undergoes the chemical part of the electrode reaction. Since the matrix material is also an electronic conductor, it can also act as the electrode s current collector. The electrochemical part of the reaction takes place on the outer surface of the composite electrode. 

Other useful solid-state electrodes are based on silver compounds (particularly silver sulfide). Silver sulfide is an ionic conductor, in which silver ions are the mobile ions. Mixed pellets containing Ag2S-AgX (where X = Cl, Br, I, SCN) have been successfiilly used for the determination of one of these particular anions. The behavior of these electrodes is determined primarily by the solubility products involved. The relative solubility products of various ions with Ag+ thus dictate the selectivity (i.e., kt] = KSp(Agf)/KSP(Aw)). Consequently, the iodide electrode (membrane of Ag2S/AgI) displays high selectivity over Br- and Cl-. In contrast, die chloride electrode suffers from severe interference from Br- and I-. Similarly, mixtures of silver sulfide with CdS, CuS, or PbS provide membranes that are responsive to Cd2+, Cu2+, or Pb2+, respectively. A limitation of these mixed-salt electrodes is tiiat the solubility of die second salt must be much larger than that of silver sulfide. A silver sulfide membrane by itself responds to either S2- or Ag+ ions, down to die 10-8M level. 

Today, the term solid electrolyte or fast ionic conductor or, sometimes, superionic conductor is used to describe solid materials whose conductivity is wholly due to ionic displacement. Mixed conductors exhibit both ionic and electronic conductivity. Solid electrolytes range from hard, refractory materials, such as 8 mol% Y2C>3-stabilized Zr02(YSZ) or sodium fT-AbCb (NaAluOn), to soft proton-exchange polymeric membranes such as Du Pont s Nafion and include compounds that are stoichiometric (Agl), non-stoichiometric (sodium J3"-A12C>3) or doped (YSZ). The preparation, properties, and some applications of solid electrolytes have been discussed in a number of books2 5 and reviews.6,7 The main commercial application of solid electrolytes is in gas sensors.8,9 Another emerging application is in solid oxide fuel cells.4,5,1, n... 

Although several metals, such as Pt and Ag, can also act as electrocatalysts for reaction (3.7) the most efficient electrocatalysts known so far are perovskites such as Lai-xSrxMn03. These materials are mixed conductors, i.e., they exhibit both anionic (O2 ) and electronic conductivity. This, in principle, can extend the electrocatalytically active zone to include not only the three-phase-boundaries but also the entire gas-exposed electrode surface. 

H.L. Tuller, J. Schoonman, and I. Riess, eds., Oxygen ion and mixed conductors and their technological applications, in NATO ASI Series, E Applied Sciences, Kluwer Academic Publishers, Dordecht (2000). 

S. Bebelis, M. Makri, A. Buekenhoudt, J. Luyten, S. Brosda, P. Petrolekas, C. Pliangos, and C.G. Vayenas, Electrochemical activation of catalytic reactions using anionic, cationic and mixed conductors, Solid State Ionics 129, 33-46 (2000). 

It will also be shown that the absolute electrode potential is not a property of the electrode but is a property of the electrolyte, aqueous or solid, and of the gaseous composition. It expresses the energy of solvation of an electron at the Fermi level of the electrolyte. As such it is a very important property of the electrolyte or mixed conductor. Since several solid electrolytes or mixed conductors based on ZrC>2, CeC>2 or TiC>2 are used as conventional catalyst supports in commercial dispersed catalysts, it follows that the concept of absolute potential is a very important one not only for further enhancing and quantifying our understanding of electrochemical promotion (NEMCA) but also for understanding the effect of metal-support interaction on commercial supported catalysts. 

Observing NEMCA, and actually very pronounced one, with Ti0224 and Ce0271 supports was at first surprising since Ti02 (rutile) and Ce02 are n-type semiconductors and their ionic (O2 ) conductivity is rather low so at best they can be considered as mixed electronic-ionic conductors.77... 

In contrast to sugar, solid sodium chloride dissolves in water to give a liquid that conducts electricity. Figure 3-19 shows that a solution of NaCl is a good conductor. When an ionic compound dissolves in water, its component cations and anions are free to move about in the solution. Mixing leads to a uniform distribution of Na and Cl ions through the entire solution, with each ion surrounded by a sheath of water molecules as shown in Figure 3-20. 

---