Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Cleaning fluid

Spirit A 0.675 40- too Rubber-based adhesives cleaning fluids, degreasing fluids... [Pg.272]

Dry bead process Dry-cell batteries Dry chemistry Dry-cleaning Dry cleaning fastness Dry-cleaning fluid Dry-cleaning solvent Dryers... [Pg.346]

Polyester fibers have exceUent resistance to soap, detergent, bleach, and other oxidiziag agents. PET fibers are generally iasoluble ia organic solvents, including cleaning fluids, but are soluble ia some phenoHc compounds, eg, (9-chlorophenol. [Pg.327]

Ideally, a system for recycling spent antifreeze consists first of the removal of the deleterious contaminants such as the corrosion products, corrosive ions, degradation products, and remaining inhibitors. Then the clean fluid could be reinhibited to a known concentration of both inhibitors and glycol. [Pg.192]

Polystyrene. Polystyrene [9003-53-6] is a thermoplastic prepared by the polymerization of styrene, primarily the suspension or bulk processes. Polystyrene is a linear polymer that is atactic, amorphous, inert to acids and alkahes, but attacked by aromatic solvents and chlorinated hydrocarbons such as dry cleaning fluids. It is clear but yellows and crazes on outdoor exposure when attacked by uv light. It is britde and does not accept plasticizers, though mbber can be compounded with it to raise the impact strength, ie, high impact polystyrene (HIPS). Its principal use in building products is as a foamed plastic (see Eoamed plastics). The foams are used for interior trim, door and window frames, cabinetry, and, in the low density expanded form, for insulation (see Styrene plastics). [Pg.327]

Sulfides, thiols, and proteinacious organic matter, particularly plasma and whole blood, seriously depress and may even aboHsh the germicidal action of mercury compounds (qv). As of this writing approved uses for mercurials are limited to contact lens cleaning fluids, spoilage prevention of stored... [Pg.135]

Automatic Dishwashing. There are many differences between laundering and automatic dishwashing. The hard surfaces present in the latter process differ from textiles because they are impermeable to sods therefore, cleaning fluids have better access to the sods. [Pg.295]

Smaii-tube Tefion Chemical resistance of tubes no tube fouling. Clean fluids, condensing, cross-exchange. Low heat transfer coefficient. 2.0-4.0... [Pg.26]

Sterilant gases Adhesives, glues Cleaning fluids Paint Eelt-tip pens Stencil machines Inks Humidifiers... [Pg.143]

When eontaminated, polluted, or valuable suspension liquors are present, it becomes necessary to wash the filter cake to effect clean separation of solids from the mother liquor or to recover the mother liquor from the solids. The operation known as dewatering involves forcing a clean fluid through the cake to recover residual liquid retained in the pores, directly after filtering or washing. Dewatering is a complex process on a microscale, because it involves the hydrodynamics of... [Pg.77]

Piping systems should be designed for an economic flow velocity. For relatively clean fluids, a recommended velocity range where minimum corrosion can be expected is 2 to 10 fps. If piping bores exist, maximum fluid velocities may have a mean velocity of 3 fps for a 3/8-in. bore to 10 fps for an 8-in.-diameter bore. Higher flow velocities are not uncommon in situations that require uniform, constant oxygen supply to form protective films on active/passive metals. [Pg.44]

Wet chemical processes A gas-cleaning process that uses certain chemicals to ensure the maximum retention of a given pollutant in the cleaning fluid. [Pg.1488]

Clean Clean fluids (e.g., dry clean air, potable water, nitrogen). [Pg.21]

The contents of the vessel are clean fluids, free from gumming or clogging matter, so that accumulation in the space between the valve inlet and the rupture disk (or in any other outlet drat may be provided) will not clog the outlet. [Pg.425]

These distributors are fabricated of pipe lengths tied to a central distribution header (usually) %vith orifice holes drilled in the bottom of the various pipe laterals off the header. This style of distributor can be fed by pressure or gravity for clean fluids. The gravity feed is considered better for critical distillation application when uniformity of the flow of the drip points (or flow points) through out the cross-section of the tower is extremely important, and is excellent for low flow requirements such as below 10 gpm/ft2 [131]. [Pg.265]

Positive displacement compressors use their lubrication system to provide additional functions. The lubrication system must inject sufficient quantities of clean fluid to provide lubrication for the compressor s internal parts, such as pistons and lobes, and to provide a positive seal between moving and stationary parts. [Pg.636]

Carbon is an excellent material, being unaffected by most industrial chemicals including corrosives, oils, solvents, water and steam. It has a temperature range of up to 260°C (500°F), coupled with a high resistance to abrasion in clean fluids. [Pg.883]

As in the compressed packing gland, lubrication also must be provided in mechanical seals. The sealing area surfaces should be lubricated and cooled with pumped fluid (if it is clean enough) or an outside source of clean fluid. However, much less lubrication is required with this type of seal because the frictional surface area is smaller... [Pg.946]


See other pages where Cleaning fluid is mentioned: [Pg.93]    [Pg.146]    [Pg.299]    [Pg.347]    [Pg.61]    [Pg.333]    [Pg.174]    [Pg.263]    [Pg.532]    [Pg.269]    [Pg.336]    [Pg.1084]    [Pg.1088]    [Pg.165]    [Pg.37]    [Pg.153]    [Pg.361]    [Pg.200]    [Pg.147]    [Pg.410]    [Pg.198]    [Pg.249]    [Pg.28]    [Pg.198]    [Pg.249]    [Pg.186]    [Pg.509]    [Pg.245]   
See also in sourсe #XX -- [ Pg.3 ]

See also in sourсe #XX -- [ Pg.42 ]




SEARCH



Drilling fluids hole cleaning

Dry-cleaning fluid

Dynamic similarity 284 Supercritical Fluid Cleaning

Liquids as Antistatic Additives for Cleaning Fluids

Pump fluid change cleaning

Sample clean-up of biological fluids

Solubility in Supercritical Fluid Cleaning

Supercritical Fluids and Clean Separations

Supercritical cleaning fluid

Supercritical fluid parts cleaning

Supercritical fluids surface cleaning

Water insoluble cleaning fluids

© 2024 chempedia.info