Calibrator external calibrators

There are different concepts for the calibration. External calibration uses the measurement of separate samples containing known amounts of analyte and we compare the signal from both, the calibration sample and our unknown sample. This method requires that the differences in the matrix of sample and calibration sample does not significantly influence the response. The use of an internal... 

Like all classical quantitative analysis methods, NMR spectroscopy needs calibration, calibration standards and a validation procedure. The standard techniques are used for calibration external calibration, the standard addition method and the internal standard method. A fourth is a special NMR calibration method, the tube-in-tube technique. A small glass tube (capillary) containing a defined amount of standard is put into the normal, larger NMR tube filled with the sample for analysis. In most cases, there are slight differences in the chemical shift of corresponding signals of the same molecule in the inner... 

Zhang, L.-S., and Combs, S. M. (1998). Double calibration (external calibration and stable isotope dilution) for determining selenium in plant tissue by hydride generation inductively coupled plasma mass spectrometry.J. Assoc. Off. Anal. Chem. Int. 81(5), 1060. 

The necessary material to perform annual verification of flaw detector is mainly composed of an electronic function generator, an external calibrated attenuator and an oscilloscope. 

A calibration curve prepared using several external standards. 

Colorplate i shows an example of a set of external standards and their corresponding normal calibration curve. 

An external standardization allows a related series of samples to be analyzed using a single calibration curve. This is an important advantage in laboratories where many samples are to be analyzed or when the need for a rapid throughput of samples is critical. Not surprisingly, many of the most commonly encountered quantitative analytical methods are based on an external standardization. 

Since a standard additions calibration curve is constructed in the sample, it cannot be extended to the analysis of another sample. Each sample, therefore, requires its own standard additions calibration curve. This is a serious drawback to the routine application of the method of standard additions, particularly in laboratories that must handle many samples or that require a quick turnaround time. For example, suppose you need to analyze ten samples using a three-point calibration curve. For a normal calibration curve using external standards, only 13 solutions need to be analyzed (3 standards and 10 samples). Using the method of standard additions, however, requires the analysis of 30 solutions, since each of the 10 samples must be analyzed three times (once before spiking and two times after adding successive spikes). 

The method of standard additions can be used to check the validity of an external standardization when matrix matching is not feasible. To do this, a normal calibration curve of Sjtand versus Cs is constructed, and the value of k is determined from its slope. A standard additions calibration curve is then constructed using equation 5.6, plotting the data as shown in Figure 5.7(b). The slope of this standard additions calibration curve gives an independent determination of k. If the two values of k are identical, then any difference between the sample s matrix and that of the external standards can be ignored. When the values of k are different, a proportional determinate error is introduced if the normal calibration curve is used. 

Using the Regression Equation Once the regression equation is known, we can use it to determine the concentration of analyte in a sample. When using a normal calibration curve with external standards or an internal standards calibration curve, we measure an average signal for our sample, Yx, and use it to calculate the value of X... 

The equation for a normal calibration curve using external standards is... 

Standardizing the Method Equations 10.32 and 10.33 show that the intensity of fluorescent or phosphorescent emission is proportional to the concentration of the photoluminescent species, provided that the absorbance of radiation from the excitation source (A = ebC) is less than approximately 0.01. Quantitative methods are usually standardized using a set of external standards. Calibration curves are linear over as much as four to six orders of magnitude for fluorescence and two to four orders of magnitude for phosphorescence. Calibration curves become nonlinear for high concentrations of the photoluminescent species at which the intensity of emission is given by equation 10.31. Nonlinearity also may be observed at low concentrations due to the presence of fluorescent or phosphorescent contaminants. As discussed earlier, the quantum efficiency for emission is sensitive to temperature and sample matrix, both of which must be controlled if external standards are to be used. In addition, emission intensity depends on the molar absorptivity of the photoluminescent species, which is sensitive to the sample matrix. 

Samples of car exhaust are collected using a 4-L glass bottle evacuated to a level of less than 2 torr. A normal calibration curve using external standards of known Pco is used to determine the Pco in the exhaust samples. 

In the absence of Fe +, the membrane is colorless, but when immersed in a solution of Fe + and C, the membrane develops a red color as a result of the formation of a Fe +-bathophenanthroline complex. A calibration curve determined using a set of external standards with known molar concentrations of Fe + gave a standardization relationship of... 

The purity of a sample of K3Fe(CN)6 was determined using linear-potential scan hydrodynamic voltammetry at a glassy carbon electrode using the method of external standards. The following data were obtained for a set of calibration standards. 

Calibration curves are usually constructed by analyzing a series of external standards and plotting the detector s signal as a function of their known concentrations. As long as the injection volume is identical for every standard and sample, calibration curves prepared in this fashion give both accurate and precise results. Unfortunately, even under the best of conditions, replicate injections may have volumes that differ by as much as 5% and often may be substantially worse. For this... 

Quantitative Calculations Quantitative analyses are often easier to conduct with HPLC than GC because injections are made with a fixed-volume injection loop instead of a syringe. As a result, variations in the amount of injected sample are minimized, and quantitative measurements can be made using external standards and a normal calibration curve. 

Janusa and co-workers report the determination of chloride by CZE. Analysis of a series of external standards gives the following calibration curve. 

Curve-Fitting Methods In the direct-computation methods discussed earlier, the analyte s concentration is determined by solving the appropriate rate equation at one or two discrete times. The relationship between the analyte s concentration and the measured response is a function of the rate constant, which must be measured in a separate experiment. This may be accomplished using a single external standard (as in Example 13.2) or with a calibration curve (as in Example 13.4). 

Color plate i shows ai external standards and th normal calibration ci... 

In addition to fulfilling the in-house requirements for quality control, state and local air monitoring networks which are collecting data for compliance purposes are required to have an external performance audit on an annual basis. Under this program, an independent organization supplies externally calibrated sources of air pollutant gases to be measured by the instrumentation undergoing audit. An audit report summarizes the performance of the instruments. If necessary, further action must be taken to eliminate any major discrepancies between the internal and external calibration results. 

Semiconductor control modules gate the thyristors, which switch cm rent to the motor field at the optimum motor speed and precise phase angle. This assures synchronizing with minimum system disturbance. On pull-out, the discharge resistor is reapplied and excitation is removed k> provide protection to the rotor winding, shaft, and external electrical system. The control resynchronizes the motor after the cause of pull-out i.n removed, if sufficient torque is available. The field is automatically applied if the motor synchronizes on reluctance torque. The control is calibrated at the factory and no field adjustment is required. The opti-... 

Are all external inspection, testing, and calibration laboratories compliant with the requirements of ISO/IEC 17025 ... 

In the upper diagram each supplier individually interprets the customer s requirements and either imposes additional requirements or neglects to pass on requirements. The net result at the end of the chain is that the external customer (the one who buys from the organization) does not get satisfaction from the transaction. In the lower diagram, each supplier refers back to the external customer s requirements to calibrate the internal customer s demands. This ensures that the net result matches exactly what the customer ordered. In reality, such calibration should not be necessary if the internal customers demonstrate traceability to external customer requirements. This can be achieved through process reviews performed in each process before instructions are transmitted to subsequent processes. 

The intent is that wherever the calibration is performed, the same standards apply. Calibrating equipment in-house should not absolve you from complying with the same requirements that you would need to impose on an external test house. 

Do require external calibration laboratories to provide calibration certificates and results. 

Because an increase in resolution causes a decrease in sensitivity, it is best to operate at the lowest resolution commensurate with good results. Some instrument data systems will allow calibration with an external reference material such as perfluorokerosene and then use of a secondary reference material for the internal mass reference. Tetraiodothiophene, vaporized using the solids probe inlet, is recommended as the secondary reference. The accurate masses are 79.9721, 127.9045, 162.9045, 206.8765, 253.8090, 293.7950, 333.7810, 460.6855, and 587.5900. For a higher mass standard, use hexaiodobenzene. Because the mass defect for these internal reference ions are so large, a resolution of 2000 is ample to separate these ions from almost any sample ions encountered in GC/MS. 

External standard method (linear calibration curve of peak areas)... 

---