By internal

Figure 6 shows the histogram of localized AE events vs axial position for the same time period as in fig.5. The location of the AE source corresponds, within source location errors (< 10-15 cm), to one of the welds under surveillance. The weld was known by ultrasonic examination to be affected by internal discontinuities. However, the position of the source could also correspond to one of the hangers. The steps observed in EA event accumulation have taken place during steady load operation, which normally corresponds to very low background noise conditions. This type of event, however, has not been observed afterwards. 

PTM Photon tunneling microscopy [12] An interface is probed with an evanescent wave produced by internal reflection of the illuminating light Surface structure... 

Since it is not possible to measure a single electrode potential, one electrode system must be taken as a standard and all others measured relative to it. By international agreement the hydrogen electrode has been chosen as the reference ... 

Under superacidic, low nucleophilicity so-called stable ion conditions, developing electron-deficient carbocations do not find reactive external nucleophiles to react with thus they stay persistent in solution stabilized by internal neighboring group interactions. 

ICIFM-21SP Monopolar Electrolyzers. Id s EM-21 SP monopolar electrolyzer incorporates stamped electrodes that are 2 mm thick and of a relatively small (0.2 m ) size (50). The electrolyte compartments are created by molded gaskets between two of the electrode plates the electrode spacing is finite and is estabHshed by gasket thickness. The electrode frames are supported from rails and are compressed between one fixed and one floating end plate by tie rods. Inlet and outlet streams are handled by internal manifolds. A crosscut view of the electrolyzer is shown in Eigure 21. As of 1989, ICI had Hcensed 20 plants having an annual capacity of 468,250 t of NaOH. 

Ferrites aHowing for operation at frequencies well above 1 MH2 have also become available, eg, 3F4 and 4F1 (Table 6). Other newer industrial power ferrites are the Siemens-Matsushita N-series (28,97) the TDK PC-series (28,100), and the Thomson B-series (28,103). While moving to higher frequencies, the ferrites have been optimized for different loss contributions, eg, hysteresis losses, eddy current losses, and resonance losses. Loss levels are specified at 100°C because ambient temperature in power appHcations is about 60°C plus an increase caused by internal heat dissipation of about 40°C. 

The dissipation factor (the ratio of the energy dissipated to the energy stored per cycle) is affected by the frequency, temperature, crystallinity, and void content of the fabricated stmcture. At certain temperatures and frequencies, the crystalline and amorphous regions become resonant. Because of the molecular vibrations, appHed electrical energy is lost by internal friction within the polymer which results in an increase in the dissipation factor. The dissipation factor peaks for these resins correspond to well-defined transitions, but the magnitude of the variation is minor as compared to other polymers. The low temperature transition at —97° C causes the only meaningful dissipation factor peak. The dissipation factor has a maximum of 10 —10 Hz at RT at high crystallinity (93%) the peak at 10 —10 Hz is absent. 

Stereoselective All lations. Ben2ene is stereoselectively alkylated with chiral 4-valerolactone in the presence of aluminum chloride with 50% net inversion of configuration (32). The stereoselectivity is explained by the coordination of the Lewis acid with the carbonyl oxygen of the lactone, resulting in the typ displacement at the C—O bond. Partial racemi2ation of the substrate (incomplete inversion of configuration) results by internal... 

Chemistry. Coal gasification iavolves the thermal decomposition of coal and the reaction of the carbon ia the coal, and other pyrolysis products with oxygen, water, and hydrogen to produce fuel gases such as methane by internal hydrogen shifts... 

Fig. 1. Principal stresses acting on small element of cylinder waU at radius, r, when the cylinder is stressed elastically by internal pressure, (3).

Both sohd-solution hardening and precipitation hardening can be accounted for by internal strains generated by inserting either solute atoms or particles in an elastic matrix (11). The degree of elastic misfit, 5, produced by the difference, Ai , between the lattice parameter, of the pure matrix and a, the lattice parameter of the solute atom is given by... 

The transport of phthalates by road tankers and ships within Europe is carried out by international companies with sophisticated tank cleaning facihties. Wash waters from these modem faciUties are passed through a series of separators to remove any residual plasticizer which is then incinerated. It is estimated that, as a result of cleaning and spillages, the maximum emission to the environment is 80 t/yr. 

Use of 1,3 cycloaHphatic diamines in polyamides may be similarly limited by internal amide dehydration of the conformationaHy labile cis isomers to form a tetrahydropyrimidine (38) rather than high molecular weight polyamide. 1,3-Cyclohexanediamine is, however, a component of Spandex polyureas Du Pont uses the hydrogenation product of y -phenylenediamine [108-45-2] (24) captively to produce Lycra (see Fibers, elastomeric). 

The smaller reactor approaches plug-flow behavior and exhibits a large temperature gradient. In this case, external recycle provides the same degree of back-mixing as is provided by internal circulation in the larger diameter reactor. 

Uranium and mixed uranium—plutonium nitrides have a potential use as nuclear fuels for lead cooled fast reactors (136—139). Reactors of this type have been proposed for use ia deep-sea research vehicles (136). However, similar to the oxides, ia order for these materials to be useful as fuels, the nitrides must have an appropriate size and shape, ie, spheres. Microspheres of uranium nitrides have been fabricated by internal gelation and carbothermic reduction (140,141). Another use for uranium nitrides is as a catalyst for the cracking of NH at 550°C, which results ia high yields of H2 (142). 

The quantity of ethylene transported by international tankers accounts for only 1% of production. The majority of ethylene produced in the United States and Western Europe is moved by integrated pipeline systems. 

---