Applications—Noise

The noise sources in control valves include mechanical vibration (usually below 100 dBA) hydrodynamic noise caused by liquid turbulence, cavitation, or flashing (usually below 110 dBA) and aerodynamic noise (can reach 150 dBA). In control valve design, aerodynamic noise can be a major problem. Aerodynamic noise generation, in general, is a function of mass flow rate and the pressure ratio (p /pf) across the valve. The point at which sonic speed is reached in the valve vena contracta is a function of the valve design. 

Post- Oil Energy Technology After the Age of Fossil Fuels 

Special noise element design using labyrinth passages incorporated on plates. (Courtesy of Control Components, Inc.) 

Erosion caused by high exit velocities can also cause corrosion problems. Some metals do not corrode due to a self-regenerating protective surface film however, if this film is removed by erosion faster than it is formed, the metal corrodes rapidly. For lining either noble metals or ceramics should be considered in such situations. The preferred arrangement for flashing service is to use a reduced port angle valve discharging directly into a vessel or flash tank. 

---

In some applications, noise and drift characteristics of the devices and their stability with temperature may be of concern. Usually these aspects are of secondary importance in electrochemical instrumentation. 

The filter according equation (1) allows a practical application of a second derivative, because it has only the noise amplification like a first derivative. This is shown in fig. 3 on a experimental data set. The SNR of the true second derivative is too low for correct edge detection, whereas the CT filter gives reliable results. 

Composite transducers will replace conventional transducers in applications where the improvement of test sensitivity, signal to noise ratio and axial resolution are mandatory. It must nevertheless also be noted in connection with the broadband feature that though composite probes have a specified nominal frequency, the echo signals allow no echo amplitude... 

Based upon a piezoelectric 1-3-composite material, air-bome ultrasonic probes for frequencies up to 2 MHz were developped. These probes are characterized by a bandwidth larger than 50 % as well as a signal-to-noise ratio higher than 100 dB. Applications are the thickness measurement of thin powder layers, the inspection of sandwich structures, the detection of surface near cracks in metals or ceramics by generation/reception of Rayleigh waves and the inspection of plates by Lamb waves. 

In order to obtain a high signal-to-noise ratio sufficient acoustical power is necessary. For special applications a programmable pulser (transmitter) is required in order to optimize the frequency spectrum. 

In testing materials with high sound damping, the burst transmitter increases the signal-to-noise ratio to, typically, 12 dB. Typical applications honeycomb and concrete components, and air-coupled testing. 

For special applications such as air coupled testing a special programmable transmitter board was developed. This transmitter generates rectangular and burst signals, which increase the acoustical power in an optimized frequency range, and provides a superior signal-to-noise ratio. 

In practice, the NEP of a room-temperature THz spectrometer is usually limited by fluctuations (shot-noise) in the ambient blackbody radiation. Usmg an optical bandwidth Av = 3 THz (limited by, for example, a polyethylene/diamond dust window), a field of view (at nomial incidence) 0 = 9 and a detecting diameter (using a so-called Winston cone, which condenses the incident radiation onto the detecting element) laboratory applications, the background-limited NEP of a bolometer is given by... 

Analytical Applications. Chemiluminescence and bioluminescence are useful in analysis for several reasons. (/) Modem low noise phototubes when properly instmmented can detect light fluxes as weak as 100 photons/s (1.7 x 10 eins/s). Thus luminescent reactions in which intensity depends on the concentration of a reactant of analytical interest can be used to determine attomole—2eptomole amounts (10 to 10 mol). This is especially useful for biochemical, trace metal, and pollution control analyses (93,260—266) (see Trace and residue analysis). (2) Light measurement is easily automated for routine measurements as, for example, in clinical analysis. 

Closure at the instant of reversal of flow is most nearly attained in these valves. This timing of closure is not the whole solution to noise and shock at check valves. For example, if cessation of pressure at the inlet of a valve produces flashing of the decelerating stream downstream from the valve or if stoppage of flow is caused By a sudden closure of a valve some distance downstream from the check valve and the stoppage is followed by returning water hammer, slower closure may be necessary. For these applications, tilting-disk check valves are equipped with external dashpots. They are also available with low-cost insert Dodies. 

Textile motors Crane motors Determining the size of motor Sugar centrifuge motors Motors for deep-well pumps Motors for agricultural application Surface-cooled motors Torque motors or actuator motors Vibration and noise level Service factors Motors for hazardous locations Specification of motors for Zone 0 locations Specification of motors for Zone I locations Motors for Zone 2 locations Motors for mines, collieries and quarries Intrinsically safe circuits, type Ex. f Testing and certifying authorities Additional requirements for ciritical installations Motors for thermal power station auxiliaries Selection of a special-purpose motor... 

In ae off-line applications the common-mode choke is typically used and its design procedure can be found in Appendix E. The Alters resemble pi Alters, but are actually bi-directional L-C Alters. The important function is to Alter the noise generated by the switcher before it exits via the input power lines. 

---