Allylation conditions

Dienes incorporated in a cyclohexane skeleton show different reaction features from acyclic dienes. Under the reductive allylation conditions, o> (2,4-cyclohexadienyl)alkanals 15 react to provide a homoallylation product 16a (n = 1) as a major product or 16a (n = 2) exclusively (Eq. 7) [ 19]. The expected allylation product is obtained as a minor product only for the reaction of 15 (n = 1). 

When the ferf-butoxycarbonyl (Boc) carbamate-derived sulfone 5 was subjected to the Bi(OTf)34H20-catalyzed allylation conditions (Scheme 2), the cyclic carbamate 6 was obtained as the major product (36%, diastereoisomeric ratio (dr) = 82 18), along with the corresponding allylation product 7, although in low yield (16%). Such cyclic carbamate resulting from the internal capture of an intermediate (3-silyl cation with the Boc group and concomitant loss of isobutylene has already been reported in the literature [59]. 

Allylation conditions are similar to those used for benzylation to a certain extent. Williamson s etherification using allyl bromides and NaH smoothly produces the allyl ethers [85], NaH can be replaced with BaO when base-sensitive moieties are present in the molecule [86, 87], The use of allyl imidates or TMSOTf-catalyzed Et3SiH-reductive allylation of a TMS ether using allyl aldehydes also provides the... 

Chiral rhodium catalyst 118, pioneered by Nishiyama, has been put to use in the addition of allyltributylstannane to achiral aldehydes [91], This catalyst is relatively insensitive to water and can even be purified by silica gel chromatography. The optimized allylation conditions employ 1 equiv of the aldehyde, 1.5 equiv of allyltributylstannane, and 5 mol% of 118 (Scheme 10-53). The reactions with many different aldehydes can all be performed at room temperature to provide good yields of the desired homoallylic alcohols albeit in moderate to poor enan-tioselectivity. 

Recent reports of the rapid transmetalation of the highly functionalized allylic stannane 216 (Scheme 5.2.49) leads to the trichloro species 217, which provides for greater Lewis acidity and increased reactivity compared to the parent trialkyl reagent. Although transmetalation assumes a dynamic equilibrium of 217 and 218, optimized allylation conditions using SnCU (1.0 equivalent) give the syn,anti-product 219 in 96% yield. 

Torgov introduced an important variation of the Michael addition allylic alcohols are used as vinylogous a -synthons and 1,3-dioxo compounds as d -reagents (S.N. Ananchenko, 1962, 1963 H. Smith, 1964 C. Rufer) 1967). Mild reaction conditions have been successful in the addition of ],3-dioxo compounds to vinyl ketones. Potassium fluoride can act as weakly basic, non-nudeophilic catalyst in such Michael additions under essentially non-acidic and non-basic conditions (Y. Kitabara, 1964). 

Typical nucleophiles known to react with coordinated alkenes are water, alcohols, carboxylic acids, ammonia, amines, enamines, and active methylene compounds 11.12]. The intramolecular version is particularly useful for syntheses of various heterocyclic compounds[l 3,14]. CO and aromatics also react with alkenes. The oxidation reactions of alkenes can be classified further based on these attacking species. Under certain conditions, especially in the presence of bases, the rr-alkene complex 4 is converted into the 7r-allylic complex 5. Various stoichiometric reactions of alkenes via 7r-allylic complex 5 are treated in Section 4. 

The oxidation of higher alkenes in organic solvents proceeds under almost neutral conditions, and hence many functional groups such as ester or lac-tone[26,56-59], sulfonate[60], aldehyde[61-63], acetal[60], MOM ether[64], car-bobenzoxy[65], /-allylic alcohol[66], bromide[67,68], tertiary amine[69], and phenylselenide[70] can be tolerated. Partial hydrolysis of THP ether[71] and silyl ethers under certain conditions was reported. Alcohols are oxidized with Pd(II)[72-74] but the oxidation is slower than the oxidation of terminal alkenes and gives no problem when alcohols are used as solvents[75,76]. 

In contrast to oxidation in water, it has been found that 1-alkenes are directly oxidized with molecular oxygen in anhydrous, aprotic solvents, when a catalyst system of PdCl2(MeCN)2 and CuCl is used together with HMPA. In the absence of HMPA, no reaction takes place(100]. In the oxidation of 1-decene, the Oj uptake correlates with the amount of 2-decanone formed, and up to 0.5 mol of O2 is consumed for the production of 1 mol of the ketone. This result shows that both O atoms of molecular oxygen are incorporated into the product, and a bimetallic Pd(II) hydroperoxide coupled with a Cu salt is involved in oxidation of this type, and that the well known redox catalysis of PdXi and CuX is not always operalive[10 ]. The oxidation under anhydrous conditions is unique in terms of the regioselective formation of aldehyde 59 from X-allyl-A -methylbenzamide (58), whereas the use of aqueous DME results in the predominant formation of the methyl ketone 60. Similar results are obtained with allylic acetates and allylic carbonates[102]. The complete reversal of the regioselectivity in PdCli-catalyzed oxidation of alkenes is remarkable. 

Allylic amines are coupled to halides giving either allylic amines or enamines depending on the reaction condition. Reaction of steroidal dienyl triflate with Boc-diprotected allylamine affords allylamine. Use of AcOK as a base is crucial for the clean coupling[102]. The tert-allylic amine 123 reacts with an aryl halide to give the enamine 125 in DMF and allylic amine 124 in nonpolar solvents[103]. 

In addition to the catalytic allylation of carbon nucleophiles, several other catalytic transformations of allylic compounds are known as illustrated. Sometimes these reactions are competitive with each other, and the chemo-selectivity depends on reactants and reaction conditions. 

Allylic acetates are widely used. The oxidative addition of allylic acetates to Pd(0) is reversible, and their reaction must be carried out in the presence of bases. An important improvement in 7r-allylpalladium chemistry has been achieved by the introduction of allylic carbonates. Carbonates are highly reactive. More importantly, their reactions can be carried out under neutral con-ditions[13,14]. Also reactions of allylic carbamates[14], allyl aryl ethers[6,15], and vinyl epoxides[16,17] proceed under neutral conditions without addition of bases. 

Allylation under basic conditions. Allylation can be carried out under basic conditions with allylic acetates and phosphates, and under neutral conditions with carbonates and vinyloxiranes. The allylations under neutral conditions are treated separately in Section 2.2.2.1 from those under basic conditions. However, in some cases, allylations of the same substrates are carried out under both basic and neutral conditions to give similar results. These reactions are treated together in this section for convenience. Allylic acetates are widely used for Pd-catalyzed allylation in the presence of bases tertiary amines or NaH are commonly used[6,7,4l]. As a base, basic alumina or ICF on alumina is conveniently used, because it is easy to remove by filtration after the reaction[42]. Allyl phosphates are more reactive than acetates. The allylation with 40 proceeds stepwise. At first allylic phosphate reacts with malonate and then allylic acetate reacts with amine to give 41(43]. 

Allylation with allyl borates takes place smoothly under neutral conditions. Allylic alcohols are also used for allylation in the presence of boron oxide by in situ formation of allylic borates[125]. Similarly, arsenic oxide is used for allylation with allylic aleohols[126]. In addition, it was claimed that the allyl alkyl ethers 201. which are inert by themselves, can be used for the allylation in the presence of boron oxide[127]. 

Wylation under neutral conditions. Reactions which proceed under neutral conditions are highly desirable, Allylation with allylic acetates and phosphates is carried out under basic conditions. Almost no reaction of these allylic Compounds takes place in the absence of bases. The useful allylation under neutral conditions is possible with some allylic compounds. Among them, allylic carbonates 218 are the most reactive and their reactions proceed under neutral conditions[13,14,134], In the mechanism shown, the oxidative addition of the allyl carbonates 218 is followed by decarboxylation as an irreversible process to afford the 7r-allylpalladium alkoxide 219. and the generated alkoxide is sufficiently basic to pick up a proton from active methylene compounds, yielding 220. This in situ formation of the alkoxide. which is a... 

Since allylation with allylic carbonates proceeds under mild neutral conditions, neutral allylation has a wide application to alkylation of labile compounds which are sensitive to acids or bases. As a typical example, successful C-allylation of the rather sensitive molecule of ascorbic acid (225) to give 226 is possible only with allyl carbonate[l 37]. Similarly, Meldrum s acid is allylated smoothly[138]. Pd-catalyzed reaction of carbon nucleophiles with isopropyl 2-methylene-3,5-dioxahexylcarbomite (227)[I39] followed by hydrolysis is a good method for acetonylation of carbon nucleophiles. 

Allylation of the 10-carborane 236 (pKa = 18-22) with diallyl carbonate is possible under neutral conditions to give 237[146], Allylation and rearrangement of the trialkylalkynylborane 238 affords the trisubstituted alkene 239 stereoselectively [ 147],... 

The TT-allylpalladium complexes 241 formed from the ally carbonates 240 bearing an anion-stabilizing EWG are converted into the Pd complexes of TMM (trimethylenemethane) as reactive, dipolar intermediates 242 by intramolecular deprotonation with the alkoxide anion, and undergo [3 + 2] cycloaddition to give five-membered ring compounds 244 by Michael addition to an electron-deficient double bond and subsequent intramolecular allylation of the generated carbanion 243. This cycloaddition proceeds under neutral conditions, yielding the functionalized methylenecyclopentanes 244[148], The syn-... 

Diphenylketene (253) reacts with allyl carbonate or acetate to give the a-allylated ester 255 at 0 °C in DMF, The reaction proceeds via the intermediate 254 formed by the insertion of the C = C bond of the ketene into 7r-allylpalla-dium, followed by reductive elimination. Depending on the reaction conditions, the decarbonylation and elimination of h-hydrogen take place in benzene at 25 °C to afford the conjugated diene 256(155]. 

Allyl aryl ethers are used for allylation under basic conditionsfh], but they can be cleaved under neutral conditions. Formation of the five-membered ring compound 284 based on the cyclization of 283 has been applied to the syntheses of methyl jasmonate (285)[15], and sarkomycin[169]. The trisannulation reagent 286 for steroid synthesis undergoes Pd-catalyzed cyclization and aldol condensation to afford CD rings 287 of steroids with a functionalized 18-methyl group 170]. The 3-vinylcyclopentanonecarboxylate 289, formed from 288, is useful for the synthesis of 18-hydroxyestrone (290)[I7I]. 

Hydroxylysine (328) was synthesized by chemoselective reaction of (Z)-4-acet-oxy-2-butenyl methyl carbonate (325) with two different nucleophiles first with At,(9-Boc-protected hydroxylamine (326) under neutral conditions and then with methyl (diphenylmethyleneamino)acetate (327) in the presence of BSA[202]. The primary allylic amine 331 is prepared by the highly selective monoallylation of 4,4 -dimethoxybenzhydrylamine (329). Deprotection of the allylated secondary amine 330 with 80% formic acid affords the primary ally-lamine 331. The reaction was applied to the total synthesis of gabaculine 332(203]. 

Silyl ethers serve as preeursors of nucleophiles and liberate a nucleophilic alkoxide by desilylation with a chloride anion generated from CCI4 under the reaction conditions described before[124]. Rapid intramolecular stereoselective reaction of an alcohol with a vinyloxirane has been observed in dichloro-methane when an alkoxide is generated by desilylation of the silyl ether 340 with TBAF. The cis- and tru/u-pyranopyran systems 341 and 342 can be prepared selectively from the trans- and c/.y-epoxides 340, respectively. The reaction is applicable to the preparation of 1,2-diol systems[209]. The method is useful for the enantioselective synthesis of the AB ring fragment of gambier-toxin[210]. Similarly, tributyltin alkoxides as nucleophiles are used for the preparation of allyl alkyl ethers[211]. 

Phenols arc highly reactive 0-nucleophiles and allylated easily with allylic carbonates under neutral conditions. EWGs on phenols favor the reac-tion[213]. Allylic acetates are used for the allylation of phenol in the presence of KF-alumina as a base[214]. 

Various S-nucleophiles are allylated. Allylic acetates or carbonates react with thiols or trimethylsilyl sulfide (353) to give the allylic sulfide 354[222], Allyl sulfides are prepared by Pd-catalyzed allylic rearrangement of the dithio-carbonate 355 with elimination of COS under mild conditions. The benzyl alkyl sulfide 357 can be prepared from the dithiocarbonate 356 at 65 C[223,224], The allyl aryl sufide 359 is prepared by the reaction of an allylic carbonate with the aromatic thiol 358 by use of dppb under neutral condi-tions[225]. The O-allyl phosphoro- or phosphonothionate 360 undergoes the thiono thiolo allylic rearrangement (from 0-allyl to S -allyl rearrangement) to afford 361 and 362 at 130 C[226],... 

Allylic carbonates are most reactive. Their carbonylation proceeds under mild conditions, namely at 50 C under 1-20 atm of CO. Facile exchange of CO2 with CO takes place[239]. The carbonylation of 2,7-octadienyl methyl carbonate (379) in MeOH affords the 3,8-nonadienoate 380 as expected, but carbonylation in AcOH produces the cyclized acid 381 and the bicyclic ketones 382 and 383 by the insertion of the internal alkene into Tr-allylpalladium before CO insertion[240] (see Section 2.11). The alkylidenesuccinate 385 is prepared in good yields by the carbonylation of the allylic carbonate 384 obtained by DABCO-mediated addition of aldehydes to acrylate. The E Z ratios are different depending on the substrates[241]. 

It is known that tr-allylpalladium acetate is converted into allyl acetate by reductive elimination when it is treated with CO[242,243]. For this reason, the carbonylation of allylic acetates themselves is difficult. The allylic acetate 386 is carbonylated in the presence of NaBr (20-50 mol%) under severe conditions, probably via allylic bromides[244]. However, the carbonylation of 5-phenyl-2,4-pentadienyl acetate (387) was carried out in the presence of EtiN without using NaBr at 100 °C to yield methyl 6-phenyl-3,5-hexadienoate (388)[245J. The dicarbonylation of l,4-diacetoxy-2-butene to form the 3-hexenedioate also proceeds by using tetrabutylphosphonium chloride as a ligand in 49% yield[246]. 

Carbonylation of allylic alcohols requires severe conditions[248]. The carbonylation of allylic alcohols proceeds smoothly in the presence of LiCl and Ti(IV) isopropoxide[249j. The allylic methyl ether 394 can be carbonylated with the use of PdCl2[250] or 7r-allylpalladium coordinated by BF4, PF, and... 

Allylamines are not easily cleaved with Pd catalysts, but the carbonylation of the allylic amine 395 proceeds at 110 C to give the /3,7-unsaturated amide 396 by using dppp as a ligand[252], Dccarboxylation-carbonylation of allyl diethyl-carbamate under severe conditions (100 C, 80 atm) affords /3,7-unsaturated amides[2531. The 3-vinylaziridine 397 is converted into the a-vinyl-J-lactam 398 under mild conditions[254]. 

The /3,7-unsaturated aldehyde 407 is prepared in good yields by the carbo-nylation of an allylic chloride under mild conditions using tributyltin hydride as a hydride source[261]. Aldehydes are obtained in moderate yields by the reaction of CO and H2[262],... 

---