Alkyl halides chloride

In processes of producing alkylamines, and particularly methyl-amines, by reacting the corresponding alkyl chlorides, halides, hydroxides and so forth, with ammonia or ammonium salts such as ammonium chloride, the reaction product usually contains substantial quantities of all three of the primary, secondary and tertiary amines, even though the temperature, pressure, proportions and other reaction conditions may be controlled so as to give rise to a preponderance of one of said amines. 

Alkyl chlorides react slowly and the yield of the derivative is poor. Tertiary halides give anomalous results. 

Place a mixture of 0-5 g. of finely powdered thiourea, 0-5 g. of the alkyl halide and 5 ml. of alcohol in a test-tube or small flask equipped with a reflux condenser. Reflux the mixture for a j)eriod depending upon the nature of the halide primary alkyl bromides and iodides, 10-20 minutes (according to the molecular weight) secondary alkyl bromides or iodides, 2-3 hours alkyl chlorides, 3-5 hours polymethy lene dibromides or di-iodides, 20-50 minutes. Then add 0 5 g. of picric acid, boil until a clear solution is obtained, and cool. If no precipitate is obtained, add a few drops of water. RecrystaUise the resulting S-alkyl-iso-thiuronium picrate from alcohol. 

Mix together 1 0 g. of pure p-naphthol and the theoretical quantity of 50 per cent, potassium hydroxide solution, add 0-5 g. of the halide, followed by sufficient rectified spirit to produce a clear solution. For alkyl chlorides, the addition of a little potassium iodide is recommended. Heat the mixture under reflux for 15 minutes, and dissolve any potassium halide by the addition of a few drops of water. The p-naphthyl ether usually crystallises out on cooling if it does not, dilute the solution with 10 per cent, sodium hydroxide solution untU precipitation occurs. Dissolve the p-naphthyl ether in the minimum volume of hot alcohol and add the calculated quantity of picric acid dissolved in hot alcohol. The picrate separates out on cooling. Recrystallise it from rectified spirit. 

Secondary and pnmary alcohols do not react with HCl at rates fast enough to make the preparation of the conespondmg alkyl chlorides a method of practical value There fore the more reactive hydrogen halide HBr is used even then elevated temperatures are required to increase the rate of reaction... 

The order of alkyl halide reactivity in nucleophilic substitutions is the same as their order m eliminations Iodine has the weakest bond to carbon and iodide is the best leaving group Alkyl iodides are several times more reactive than alkyl bromides and from 50 to 100 times more reactive than alkyl chlorides Fluorine has the strongest bond to car bon and fluonde is the poorest leaving group Alkyl fluorides are rarely used as sub states m nucleophilic substitution because they are several thousand times less reactive than alkyl chlorides... 

Electrophilic attack on the sulfur atom of thiiranes by alkyl halides does not give thiiranium salts but rather products derived from attack of the halide ion on the intermediate cyclic salt (B-81MI50602). Treatment of a s-2,3-dimethylthiirane with methyl iodide yields cis-2-butene by two possible mechanisms (Scheme 31). A stereoselective isomerization of alkenes is accomplished by conversion to a thiirane of opposite stereochemistry followed by desulfurization by methyl iodide (75TL2709). Treatment of thiiranes with alkyl chlorides and bromides gives 2-chloro- or 2-bromo-ethyl sulfides (Scheme 32). Intramolecular alkylation of the sulfur atom of a thiirane may occur if the geometry is favorable the intermediate sulfonium ions are unstable to nucleophilic attack and rearrangement may occur (Scheme 33). 

Tetrasubstituted phosphonium halides are just as effective as their ammonium counterparts. A combination of tetraphenylphosphonium bromide and either 18-crown-6 or polyethylene glycol dimethyl ether with spray-dried potassium fluoride converts 4-chlorobenzaldehyde to 4-fluorobenzaldehyde in 74% yield [67] In addition, the halogen of a primary alkyl chloride or bromide is easily displaced by fluorine in aqueous saturated potassium fluoride and a catalytic amount of hexadecyltributylphosphonium bromide [68] (Table 7 Procedure 4, p 194)... 

Differences in solubility of the reactants may for example be utilized as follows. Sodium iodide is much more soluble in acetone than are sodium chloride or sodium bromide. Upon treatment of an alkyl chloride or bromide with sodium iodide in acetone, the newly formed sodium chloride or bromide precipitates from the solution and is thus removed from equilibrium. Alkyl iodides can be conveniently prepared in good yields by this route. Alkyl bromides are more reactive as the corresponding chlorides. Of high reactivity are a-halogen ketones, a-halogen carboxylic acids and their derivatives, as well as allyl and benzyl halides. 

Secondary or tertiary alkyl halides are much less reactive. For example an alkyl dichloride with a primary and a secondary chloride substituent reacts selectively by exchange of the primary chloride. The reactivity with respect to the Finkelstein reaction is thus opposite to the reactivity for the hydrolysis of alkyl chlorides. For the Finkelstein reaction on secondary and tertiary substrates Lewis acids may be used," e.g. ZnCla, FeCls or MesAl. 

Chain extension by means of the reaction of alkyl halides with cyanide is frequently alluded to but rarely employed, mainly because of the long reaction times and poor yields usually encountered. The use of DMSO as a solvent has greatly simplified the procedures and improved the yields of many ionic reactions, and the conversion of alkyl chlorides to nitriles is a good example. 

Figure 6.10 A plot of dissociation enthalpy versus substitution pattern for the gas-phase dissociation of alkyl chlorides to yield carbocations. More highly substituted alkyl halides dissociate more easily than less highly substituted ones.

The most valuable and comprehensive kinetic studies of alkylation have been carried out by Brown et al. The first of these studies concerned benzylation of aromatics with 3,4-dichloro- and 4-nitro-benzyl chlorides (these being chosen to give convenient reaction rates) with catalysis by aluminium chloride in nitrobenzene solvent340. Reactions were complicated by dialkylation which was especially troublesome at low aromatic concentrations, but it proved possible to obtain approximately third-order kinetics, the process being first-order in halide and catalyst and roughly first-order in aromatic this is shown by the data relating to alkylation of benzene given in Table 77, where the first-order rate coefficients k1 are calculated with respect to the concentration of alkyl chloride and the second-order coefficients k2 are calculated with respect to the products of the... 

Tertiary alkyl azides can be prepared by stirring tertiary alkyl chlorides with NaN3 and ZnCl2 in 82 ° or by treating tertiary alcohols with NaN3 and CF3-COOH or with HN3 andTiCl4 or BF3. Acyl azides, which can be used in the Curtius reaction (18-14), can be similarly prepared from acyl halides, anhydrides, " esters, or other acyl derivatives. ° Acyl azides can also be prepared... 

Halide exchange, sometimes call the Finkelstein reaction, is an equilibrium process, but it is often possible to shift the equilibrium." The reaction is most often applied to the preparation of iodides and fluorides. Iodides can be prepared from chlorides or bromides by taking advantage of the fact that sodium iodide, but not the bromide or chloride, is soluble in acetone. When an alkyl chloride or bromide is treated with a solution of sodium iodide in acetone, the equilibrium is shifted by the precipitation of sodium chloride or bromide. Since the mechanism is Sn2, the reaction is much more successful for primary halides than for secondary or tertiary halides sodium iodide in acetone can be used as a test for primary bromides or chlorides. Tertiary chlorides can be converted to iodides by treatment with excess Nal in CS2, with ZnCl2 as catalyst. " Vinylic bromides give vinylic iodides with retention of configuration when treated with KI and a nickel bromide-zinc catalyst," or with KI and Cul in hot HMPA." ... 

Yet another approach uses electrolysis conditions with the alkyl chloride, Pe(CO)s and a nickel catalyst, and gives the ketone directly, in one step. In the first stage of methods 1, 2, and 3, primary bromides, iodides, and tosylates and secondary tosylates can be used. The second stage of the first four methods requires more active substrates, such as primary iodides or tosylates or benzylic halides. Method 5 has been applied to primary and secondary substrates. 

Reduction of simple alkyl halides to alkanes by ethylenediamine complexes of Cr(II), denoted Cr"(en) occurs readily , e.g. for isopropyl chloride in aqueous dimethylformamide at 25 °C simple second-order behaviour is found with ki dependent on [en]/[Cr(II)] but reaching a limiting value of 1.6x 10 l.mole . sec . Competition studies between a mixture of two alkyl chlorides for Cr(II) was achieved by estimating alkane products by gas-liquid chromatography and... 

The three picolines react with alkyl halides in liquid ammonia solution in the presence of sodamide to yield the corresponding monoalkylpyridines. a-Picoline also reacts with alkyl chlorides in the presence of sodamide either alone or in the presence of xylene to give a fair yield of monoalkylpyridine CjH N.CHjR. With y-picoliue under similar experimental conditions disubstitution of the alkyl group (CjHjN.CHRj) occurs to an appreciable extent. The preparation of tile three n-amylpyridines is described the 3- and 4-compounds by the liquid ammonia - sodamide method and the 2-compound by the sodamide-3 ene procedure. 

It is well-established that electroreduced nickel(I) complexes of cyclam and a variety of substituted cyclams add oxidatively to alkyl halides to give alkylnickel(III) complexes in organic solvents,251,276 the lifetime of the carbon-nickel bond governing the overall behavior of the system. However, it was shown that [Ni (tmc)]+ (one-electron reduced form of complex (17) tmc= 1,4,8,11-teramethyl 1,4,8,11-tetraazacyclotetradecane) reacts with alkyl chlorides in aqueous alkaline solution in a one-electron process.277,278... 

Alkyl Halides. Commonly, reductions with liquid silanes and liquid alkyl halides do not require the use of a solvent.186 When the alkyl halide is a solid, either pentane186 or dichloromethane may be used as solvent.192 No significant difference in reactivities is observed between alkyl chloride and bromide substrates,186 but allyl halides are more reactive than 2-halopropanes, which, in turn, are more reactive than 1-halopropanes.190,146... 

Examples of w-allylnickel-X compounds (X = anionic ligand) other than 77-allylnickel halides which have been used in combination with (alkyl)aluminum halides as olefin oligomerization catalysts are 7r-allyl-nickel acetylacetonate (11) (Section III), 7r-allylnickel aziridide (4, 56), and bis(7r-allyl)nickel (6) (59). In addition to ir-allylnickel halides, organo-nickel halides such as tritylnickel chloride (60, 61) and pentafluoro-phenylbis(triphenylphosphine)nickel bromide (62), or hydridonickel halides, e.g., trans-hydridobis(triisopropylphosphine)nickel chloride (12) (Section III), give active catalysts after activation with aluminum halides... 

The numerous straightforward examples of internal displacement reactions leading to isolable cyclic products will not be discussed here, but only, for the most part, those ionization reactions in which a cyclic intermediate or transition state is deduced from the rearranged structure of the product. A well-known example is mustard gas and other alkyl chlorides with sulfur on the /3-carbon atom. Although mustard gas is a primary and saturated alkyl chloride, its behavior is like that of a typical tertiary alkyl chloride. It reacts so fast by a first order ionization that the rate of the usual second order displacement reaction of primary alkyl halides is not measureable. Only the ultimate product, not the rate, is determined by the added reagent.228 Since the effect of the sulfur is too large to be explicable in terms of a carbon sulfur dipole or similar explanation, a cyclic sulfonium ion has been proposed as an... 

Several methods for the preparation of the parent compound in this system, tris(trimethylsilyl)phosphite, have been reported.114 118 The application of this and related reagents in reaction with alkyl halides has been reported and used for the preparation of a variety of phosphonic acid analogues of phospholipids.114119-124 Interestingly, alkyl chlorides appear to be more reactive with the silyl reagents than do alkyl iodides, a reversal of the normally observed trend with alkyl esters of the phosphorus acids. (The particular use of silyl phosphorus reagents for the synthesis of biologically significant compounds has... 

Synthetic organic chemistry applications employing alkane C-H functionalizations are now well established. For example, alkanes can be oxidized to alkyl halides and alcohols by the Shilov system employing electrophilic platinum salts. Much of the Pt(ll)/Pt(rv) alkane activation chemistry discussed earlier has been based on Shilov chemistry. The mechanism has been investigated and is thought to involve the formation of a platinum(ll) alkyl complex, possibly via a (T-complex. The Pt(ll) complex is oxidized to Pt(iv) by electron transfer, and nucleophilic attack on the Pt(iv) intermediate yields the alkyl chloride or alcohol as well as regenerates the Pt(n) catalyst. This process is catalytic in Pt(ll), although a stoichiometric Pt(rv) oxidant is often required (Scheme 6).27,27l 2711... 

Carbon monoxide rapidly inserts into the carbon—zirconium bond of alkyl- and alkenyl-zirconocene chlorides at low temperature with retention of configuration at carbon to give acylzirconocene chlorides 17 (Scheme 3.5). Acylzirconocene chlorides have found utility in synthesis, as described elsewhere in this volume [17]. Lewis acid catalyzed additions to enones, aldehydes, and imines, yielding a-keto allylic alcohols, a-hydroxy ketones, and a-amino ketones, respectively [18], and palladium-catalyzed addition to alkyl/aryl halides and a,[5-ynones [19] are examples. The acyl complex 18 formed by the insertion of carbon monoxide into dialkyl, alkylaryl, or diaryl zirconocenes may rearrange to a r 2-ketone complex 19 either thermally (particularly when R1 = R2 = Ph) or on addition of a Lewis acid [5,20,21]. The rearrangement proceeds through the less stable... 

HMPT catalysis.13 Sml2 alone can reduce primary alkyl bromides or iodides in high yield, but the reaction is slow even in refluxing THF. In the presence of HMPT ( 5 mole %), alkyl, aryl, and vinyl halides, and even alkyl chlorides, are reduced in almost quantitative yield at 25°, often in less than 1 hour. 

---