Acrylic acid hydrolysis

Poly(acrylic acid) and Poly(methacrylic acid). Poly(acryHc acid) (8) (PAA) may be prepared by polymerization of the monomer with conventional free-radical initiators using the monomer either undiluted (36) (with cross-linker for superadsorber appHcations) or in aqueous solution. Photochemical polymerization (sensitized by benzoin) of methyl acrylate in ethanol solution at —78° C provides a syndiotactic form (37) that can be hydrolyzed to syndiotactic PAA. From academic studies, alkaline hydrolysis of the methyl ester requires a lower time than acid hydrolysis of the polymeric ester, and can lead to oxidative degradation of the polymer (38). Po1y(meth acrylic acid) (PMAA) (9) is prepared only by the direct polymerization of the acid monomer it is not readily obtained by the hydrolysis of methyl methacrylate. 

The amide group is readily hydrolyzed to acrylic acid, and this reaction is kinetically faster in base than in acid solutions (5,32,33). However, hydrolysis of N-alkyl derivatives proceeds at slower rates. The presence of an electron-with-drawing group on nitrogen not only facilitates hydrolysis but also affects the polymerization behavior of these derivatives (34,35). With concentrated sulfuric acid, acrylamide forms acrylamide sulfate salt, the intermediate of the former sulfuric acid process for producing acrylamide commercially. Further reaction of the salt with alcohols produces acrylate esters (5). In strongly alkaline anhydrous solutions a potassium salt can be formed by reaction with potassium / /-butoxide in tert-huty alcohol at room temperature (36). 

The first commercial process for manufacture of acryHc acid (qv) and acrylates involved hydrolysis of ethylene cyanohydrin in aqueous sulfuric acid. 

Electrochemical reduction of oxazolinium salts 36 gives the anions 37, which add efficiently to alkyl halides or, in the presence of McsSiCl, to methyl acrylate, methyl vinyl ketone, and acrylonitrile. Simple acid hydrolysis then gives the ketone products 38 and 39, and this method is quite general since the starting salts are readily prepared from carboxylic acids, R C02H (87TL4411). 

The 2-phenyl-2-ethyl-pentane-1,5-diacid-mononitrile-(1) of melting point 72° to 76°C, used as starting material in this process, can be produced for example from o-phenyl-butyric acid nitrile by condensation with acrylic acid methyl ester and subsequent hydrolysis of the thus-obtained 2-phenyl-2-ethyl-pentane-1,5-diacid-monomethyl ester-mononltrile-(l) of boiling point 176° to 185°C under 12 mm pressure. 

The main use of acrolein is to produce acrylic acid and its esters. Acrolein is also an intermediate in the synthesis of pharmaceuticals and herhicides. It may also he used to produce glycerol hy reaction with isopropanol (discussed later in this chapter). 2-Hexanedial, which could he a precursor for adipic acid and hexamethylene-diamine, may he prepared from acrolein Tail to tail dimenization of acrolein using ruthenium catalyst produces trans-2-hexanedial. The trimer, trans-6-hydroxy-5-formyl-2,7-octadienal is coproduced. Acrolein, may also he a precursor for 1,3-propanediol. Hydrolysis of acrolein produces 3-hydroxypropionalde-hyde which could he hydrogenated to 1,3-propanediol. ... 

Acrylonitrile is mainly used to produce acrylic fibers, resins, and elastomers. Copolymers of acrylonitrile with butadiene and styrene are the ABS resins and those with styrene are the styrene-acrylonitrile resins SAN that are important plastics. The 1998 U.S. production of acrylonitrile was approximately 3.1 billion pounds. Most of the production was used for ABS resins and acrylic and modacrylic fibers. Acrylonitrile is also a precursor for acrylic acid (by hydrolysis) and for adiponitrile (by an electrodimerization). 

So far, many kinds of nucleophiles active for hydrolysis such as imidazolyl-, amino-, pyridino-, carboxyl- and thiol-groups, have been used for preparation of hydrolase models. Overberger et al.108,1091 prepared copolymers of vinylimidazole and acrylic acid 60 (PVIm AA), by which the cationic substrate, 61 (ANTI), was hydrolyzed. This kind of copolymer is considered to be a model of acetylcholinesterase. With ANTI, the rate of the copolymer catalysis was higher than that of imidazole itself in the higher values of pH, as is seen in Table 9. In this work, important contributions of the electrostatic interactions are clear. The activity of the copolymer was not as high with the negatively charged and neutral substrates. 

A variety of ionomers have been described in the research literature, including copolymers of a) styrene with acrylic acid, b) ethyl acrylate with methacrylic acid, and (c) ethylene with methacrylic acid. A relatively recent development has been that of fluorinated sulfonate ionomers known as Nafions, a trade name of the Du Pont company. These ionomers have the general structure illustrated (10.1) and are used commercially as membranes. These ionomers are made by copolymerisation of the hydrocarbon or fluorocarbon monomers with minor amounts of the appropriate acid or ester. Copolymerisation is followed by either neutralisation or hydrolysis with a base, a process that may be carried out either in solution or in the melt. 

As was noted previously, Hine and Bailey (16, 17) have obtained correlation of rate data for the reaction of tra s-3-substituted acrylic acids and diphenyl-diazomethane with the Hammett equation. Bowden has reported correlation of rate data for the reaction of tra s-3-substituted acrylic acids with diphenyl-diazomethane (59) and the alkaline hydrolysis of trans-3-substituted methyl acrylates (69) with the Hammett equation. Sufficient data are available for nine sets of rate studies. The sets studied are reported in Table VIII. The results of the correlations are given in Table IX. Of the nine sets studied, seven gave... 

Scheme 2. General route to branched poly(acrylic acid) via SCVCP, followed by hydrolysis...

The following substrates were obtained from commercial sources, methyl pyruvate (1), methyl acetoacetate (2), methyl 4-oxopentanoate (1), and methyl 3-oxopentanoate ( ). Alkyl 5-oxohexanoates (4, 5 and 6) were prepared by condensation of methyl acetoacetate and methyl acrylate followed by acidic hydrolysis, decarboxylation, and esterification [8]. Methyl 3-oxo-4-methylpentanoate... 

The highly ordered cyclic TS of the D-A reaction permits design of diastereo-or enantioselective reactions. (See Section 2.4 of Part A to review the principles of diastereoselectivity and enantioselectivity.) One way to achieve this is to install a chiral auxiliary.80 The cycloaddition proceeds to give two diastereomeric products that can be separated and purified. Because of the lower temperature required and the greater stereoselectivity observed in Lewis acid-catalyzed reactions, the best diastereoselectivity is observed in catalyzed reactions. Several chiral auxiliaries that are capable of high levels of diastereoselectivity have been developed. Chiral esters and amides of acrylic acid are particularly useful because the auxiliary can be recovered by hydrolysis of the purified adduct to give the enantiomerically pure carboxylic acid. Early examples involved acryloyl esters of chiral alcohols, including lactates and mandelates. Esters of the lactone of 2,4-dihydroxy-3,3-dimethylbutanoic acid (pantolactone) have also proven useful. 

Although the potassium superoxide route can be universally applied to various alkyl methacrylates, it is experimentally more difficult than simple acid hydrolysis. In addition, limited yields do not permit well-defined hydrophobic-hydrophilic blocks. On the other hand, acid catalyzed hydrolysis is limited to only a few esters such as TBMA, but yields of carboxylate are quantitative. Hydrolysis attempts of poly(methyl methacrylate) (PMMA) and poly(isopropyl methacrylate) (PIPMA) do not yield an observable amount of conversion to the carboxylic acid under the established conditions for poly(t-butyl methacrylate) (PTBMA). This allows for selective hydrolysis of all-acrylic block copolymers. 

We have, therefore, taken a different approach (10). In a copolymer of acrylamide with acrylic acid, tEe initial rate constant for amide hydrolysis is given by... 

Introduction of 3,5-dimethyl and 4-substituent on the Phebox skeleton revealed a weak substituent effect on the degree of asymmetric induction (Scheme 15) [28,29]. When trimethylsilyl acrylate was used as enolate source, the (3-hydroxy carboxylic acid was obtained directly upon mild acid hydrolysis. In the production of carboxylic acid 49, an enantiomeric excess of 96% ee was attained using the NC -substituted Phebox-Rh catalyst. 

Hydrolysis of amide groups to carboxylate is a major cause of instability in acrylamide-based polymers, especially at alkaline pH and high temperatures. The performance of oil-recovery polymers may be adversely affected by excessive hydrolysis, which can promote precipitation from sea water solution. This work has studied the effects of the sodium salts of acrylic acid and AMPS, 2-acrylamido-2-methylpropanesulfonic acid, as comonomers, on the rate of hydrolysis of polyacrylamides in alkaline solution at high temperatures. Copolymers were prepared containing from 0-53 mole % of the anionic comonomers, and hydrolyzed in aqueous solution at pH 8.5 at 90°C, 108°C and 120°C. The extent of hydrolysis was measured by a conductometric method, analyzing for the total carboxylate content. 

The relative proportions of triads is determined by the synthetic conditions chosen as described above for acrylic acid copolymers of acrylamide derived by either direct copolymerization or by hydrolysis. Also, the polymerization pH has a considerable effect on the reactivity in acrylamide/acrylic acid copolymerization. 

In recent works, we have studied the kinetics of both hydrolysis and degradation of a acrylamide-acrylic acid copolymer containing 17% of acrylate groups. The purpose of this paper is to give some predictions of the thickening properties evolution based upon semi-empirical viscosity laws. 

---