Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Molecular weight of liquids

In determining the molecular weight of liquids the apparatus shown in Fig. 82 (p. 210) is convenient for weighing and transferring the liquid to the tube. [Pg.36]

L = latent heat of vaporization of liquid, BTU/lb M = molecular weight of liquid T = temperature of the relief vapor, °R... [Pg.478]

If we refer the latent heat to a mol of liquid, instead of unit mass, we have, if Mi, M2 are the molecular weights of liquid and vapour ... [Pg.178]

Ml apparent molecular weight of liquid in equilibrium with gas... [Pg.565]

The oldest and probably the most widely used initiator is 4,4 -azobis(4-cyano-n-pentanol). Synthesized from 5-keto-n-pentanol as starting material (Strecker synthesis), this initiator was used in hydroxytelechelic polystyrene, polyacrylonitrile, and polymethacrylate syntheses, 4). Dienes were also polymerized with this initiator by a different method the molecular weights of liquid hydroxytelechelic polymers are between 2000 and 20000, their functionality is usually higher than two 15,16) (Table 1.1). The polymerization has been studied in dependence on reaction time, monomer and initiator concentrations, temperature, and solvent. The molecular weight increases with decreasing initiator concentration or increasing reaction time. The yield is a function of the nature of monomer and solvent. It decreases in the series chloroprene > butadiene > isoprene and dioxane > toluene. [Pg.170]

Molecular Weight Of Liquid Initial Moisture (Wet Basis). ... [Pg.743]

Molecular Weight Of Liquid . Initial Moisture (Wet Basis) -Chemically Free . ----------... [Pg.800]

For the given values of p and T, calculate the liquid-vapor equilibrium for the mixture with the composition (20.13), and also the density and the molecular weights of liquid and gaseous phases, using the Peng-Robinson equation of state (see Section 5.7) ... [Pg.639]

Weissler, A., Fitzgerald, J. W. and Resnick, I., A sound velocity method for determination of molecular weight of liquid polymers, J. Appl Phys., 18, 434-438 (1947). [Pg.249]

K Equilibrium ratio Lmw Molecular weight of liquid MOC Maximum operational capacity (ft/s) VLE Vapor/liquid equilibrium X Flow parameter a Relative volatility AP Pressure drop (in. H20/ft)... [Pg.266]

After the number of trays and the draw tray locations have been set, plot the API gravity and molecular weight of liquid leaving trays versus tray number. Assume that liquids leaving the tray above and tray below draw trays have the same gravity and molecular weight as the product liquid. [Pg.83]

Ease of coating due to lower viscosity Radiation curing can be used to crosslink hot melts as well as increase the molecular weight of liquids UV lamps can usually be installed on existing production lines... [Pg.16]

Reaction order, dimensionless Molecular weight of liquid phase, gi/mol. ... [Pg.263]

See other pages where Molecular weight of liquids is mentioned: [Pg.168]    [Pg.425]    [Pg.204]    [Pg.565]    [Pg.742]    [Pg.157]    [Pg.257]    [Pg.664]    [Pg.735]    [Pg.100]    [Pg.735]    [Pg.743]    [Pg.1299]    [Pg.1068]    [Pg.310]    [Pg.311]    [Pg.291]    [Pg.916]    [Pg.251]    [Pg.72]    [Pg.74]    [Pg.466]    [Pg.469]    [Pg.464]    [Pg.468]    [Pg.291]    [Pg.50]   
See also in sourсe #XX -- [ Pg.434 ]



SEARCH



Molecular liquids

Molecular weight, liquid

© 2024 chempedia.info