Acids potentiometric titration

Directions are provided in this experiment for determining the dissociation constant for a weak acid. Potentiometric titration data are analyzed by a modified Gran plot. The experiment is carried out at a variety of ionic strengths and the thermodynamic dissociation constant determined by extrapolating to zero ionic strength. 

Phosphoric acid esters are strong acids similar to orthophosphoric acid. Potentiometric titration of a 0.1 N aqueous solution of an acid phosphoric acid ester clearly shows two potential jumps which lie at pH values of 6.5 and 11.5. The pH value of diluted aqueous solutions of acid esters lies in the range of 1-3. Phosphoric acid esters are stable against hydrolysis, but adducts of free phosphoric acid esters with ethylene oxide are generally less stable. 

After removal of fatty acid, potentiometric titration of the aqueous layer gives the methyltaurine. 

Add a known volume ofo oaM.AgNOj solution (in excess) and boil the solution until the silver chloride has coagulated. Filter through a conical 5 cm. funnel, ensuring that the filter-paper does not protrude above the r m of the funnel. Wash the silver chloride and the filter-paper several times with a fine jet of distilled water. To the united filtrate and washings add i ml. of saturated ferric alum solution. The solution should be almost colourless if it is more than faintly coloured, add a few drops of concentrated nitric acid. Then titrate with 0 02M-ammonium thiocyanate solution until the permanent colour of ferric thiocyanate is just perceptible. (Alternatively the chloride may be determined potentiometrically.)... 

The most obvious sensor for an acid-base titration is a pH electrode.For example, Table 9.5 lists values for the pH and volume of titrant obtained during the titration of a weak acid with NaOH. The resulting titration curve, which is called a potentiometric titration curve, is shown in Figure 9.13a. The simplest method for finding the end point is to visually locate the inflection point of the titration curve. This is also the least accurate method, particularly if the titration curve s slope at the equivalence point is small. 

Although not commonly used, thermometric titrations have one distinct advantage over methods based on the direct or indirect monitoring of plT. As discussed earlier, visual indicators and potentiometric titration curves are limited by the magnitude of the relevant equilibrium constants. For example, the titration of boric acid, ITaBOa, for which is 5.8 X 10 °, yields a poorly defined equivalence point (Figure 9.15a). The enthalpy of neutralization for boric acid with NaOlT, however, is only 23% less than that for a strong acid (-42.7 kj/mol... 

Values for fQi and K 2 for acids of the form H2A are determined from a least-squares analysis of data from a potentiometric titration. 

Partanen, J. I. Karki, M. H. Determination of the Thermodynamic Dissociation Constant of a Weak Acid by Potentiometric Acid-Base Titration, /. Chem. Educ. 1994,... 

Potentiometric titration curves are used to determine the molecular weight and fQ or for weak acid or weak base analytes. The analysis is accomplished using a nonlinear least squares fit to the potentiometric curve. The appropriate master equation can be provided, or its derivation can be left as a challenge. 

Powell, J. R. Tucker, S. A. Acree, Jr., et al. A Student-Designed Potentiometric Titration Quantitative Determination oflron(ll) by Caro s Acid Titration, ... 

The titration of a mixture ofp-nitrophenol (pfQ = 7.0) and m-nitrophenol pK = 8.3) can be followed spectrophotometrically. Neither acid absorbs at a wavelength of 545 nm, but their respective conjugate bases do absorb at this wavelength. The m-nitrophenolate ion has a greater absorbance than an equimolar solution of the p-nitrophenolate ion. Sketch the spectrophotometric titration curve for a 50.00-mL mixture consisting of 0.0500 M p-nitrophenol and 0.0500 M m-nitrophenol with 0.100 M NaOH, and compare the curve with the expected potentiometric titration curves. 

The potentiometric titration curve shown here was recorded on a 0.4300-g sample of a purified amino acid that was dissolved in 50.00 ml of water and titrated with 0.1036 M NaOH. Identify the amino acid from the possibilities listed in the following table. 

Potcntiomctric Titrations In Chapter 9 we noted that one method for determining the equivalence point of an acid-base titration is to follow the change in pH with a pH electrode. The potentiometric determination of equivalence points is feasible for acid-base, complexation, redox, and precipitation titrations, as well as for titrations in aqueous and nonaqueous solvents. Acid-base, complexation, and precipitation potentiometric titrations are usually monitored with an ion-selective electrode that is selective for the analyte, although an electrode that is selective for the titrant or a reaction product also can be used. A redox electrode, such as a Pt wire, and a reference electrode are used for potentiometric redox titrations. More details about potentiometric titrations are found in Chapter 9. 

The routine compositional and functional testing done on the adhesives includes gas chromatographic testing for purity, potentiometric titrations for acid stabilizer concentrations, accelerated thermal stabiUty tests for shelf life, fixture time cure speed tests, and assorted ASTM tests for tensile shear strengths, peel and impact strengths, and hot strengths. 

The method of choice for determining carboxyl groups in lignin is based on potentiometric titration in the presence of an internal standard, /)-hydroxybenzoic acid, using tetra- -butylammonium hydroxide as a titrant (42). The carboxyl contents of different lignins are shown in Table 6. In general, the carboxyl content of lignin increases upon oxidation. 

The free maleic acid content in maleic anhydride is determined by direct potentiometric titration (166). The procedure involves the use of a tertiary amine, A/-ethylpipetidine [766-09-6J, as a titrant. A tertiary amine is chosen as a titrant since it is nonreactive with anhydrides (166,167). The titration is conducted in an anhydrous solvent system. Only one of the carboxyhc acid groups is titrated by this procedure. The second hydrogen s dissociation constant is too weak to titrate (166). This test method is not only used to determine the latent acid content in refined maleic acid, but also as a measure of the sample exposure to moisture during shipping. 

Amides can be titrated direcdy by perchloric acid ia a nonaqueous solvent (60,61) and by potentiometric titration (62), which gives the sum of amide and amine salts. Infrared spectroscopy has been used to characterize fatty acid amides (63). Mass spectroscopy has been able to iadicate the position of the unsaturation ia unsaturated fatty amides (64). Typical specifications of some primary fatty acid amides and properties of bisamides are shown ia Tables 5 and 6. 

Titration of thioglycolate esters is also realized by iodine in alcohoHc solution. Titration of thioglycolic acid (acid number) in thioglycolate esters is effected by potentiometric titration with potassium hydroxide. 

There are four basic sulfates that can be identified by potentiometric titration using sodium carbonate (39,40) langite [1318-78-17, CuSO -3Cu(OH)2 H2 i brochantite [12068-81 -4] CuSO -3Cu(OH)2 antedite [12019-54-4] CuSO -2Cu(OH)2 and CuS0 -Cu0-2Cu(0H)2-xH20. The basic copper(II) sulfate that is available commercially is known as the tribasic copper sulfate [12068-81 ] CuS04-3Cu(0H)2, which occurs as the green monoclinic mineral brochantite. This material is essentially insoluble in water, but dissolves readily in cold dilute mineral acids, warm acetic acid, and ammonia solutions. 

There is also evidence for stable 3,4-adducts from the X-ray analysis of 2-amino-4-ethoxy-3,4-dihydropteridinium bromide, the nucleophilic addition product of 2-aminopteridine hydrobromide and ethanol (69JCS(B)489). The pH values obtained by potentiometric titration of (16) with acid and back-titration with alkali produces a hysteresis loop, indicating an equilibrium between various molecular species such as the anhydrous neutral form and the predominantly hydrated cation. Table 1 illustrates more aspects of this anomaly. 2-Aminop-teridine, paradoxically, is a stronger base than any of its methyl derivatives each dimethyl derivative is a weaker base than either of its parent monomethyl derivatives. Thus the base strengths decrease in the order in which they are expected to increase, with only the 2-amino-4,6,7-trimethylpteridine out of order, being more basic than the 4,7-dimethyl derivative. 

The holistic thermodynamic approach based on material (charge, concentration and electron) balances is a firm and valuable tool for a choice of the best a priori conditions of chemical analyses performed in electrolytic systems. Such an approach has been already presented in a series of papers issued in recent years, see [1-4] and references cited therein. In this communication, the approach will be exemplified with electrolytic systems, with special emphasis put on the complex systems where all particular types (acid-base, redox, complexation and precipitation) of chemical equilibria occur in parallel and/or sequentially. All attainable physicochemical knowledge can be involved in calculations and none simplifying assumptions are needed. All analytical prescriptions can be followed. The approach enables all possible (from thermodynamic viewpoint) reactions to be included and all effects resulting from activation barrier(s) and incomplete set of equilibrium data presumed can be tested. The problems involved are presented on some examples of analytical systems considered lately, concerning potentiometric titrations in complex titrand + titrant systems. All calculations were done with use of iterative computer programs MATLAB and DELPHI. 

Usually the acid-base properties of poly electrolyte are studied by potentiometric titrations. However it is well known, that understanding of polyelectrolyte properties in solution is based on the knowledge of the thermodynamic properties. Up to now, there is only a small number of microcalorimetry titrations of polyelectrolyte solutions published. Therefore we carried out potentiometric and microcalorimetric titrations of hydrochloric form of the linear and branched polyamines at 25°C and 65°C, to study the influence of the stmcture on the acid-base properties. 

Naphthenic acid is a collective name for organic acids present in some but not all crude oils. In addition to true naphthenic acids (naphthenic carboxylic acids represented by the formula X-COOH in which X is a cycloparaffin radical), the total acidity of a crude may include various amounts of other organic acids and sometimes mineral acids. Thus the total neutralization number of a stock, which is a measure of its total acidity, includes (but does not necessaiily represent) the level of naphthenic acids present. The neutralization number is the number of milligrams of potassium hydroxide required to neutralize one gram of stock as determined by titration using phenolphthalein as an indicator, or as determined by potentiometric titration. It may be as high as 10 mg KOH/gr. for some crudes. The neutralization number does not usually become important as a corrosion factor, however, unless it is at least 0.5 mg KOH/gm. 

In systems such as the 2- and 6-hydroxypteridine series, rapid potentiometric or spectrophotometric pA determinations on neutral solutions usually give values near to the acidic pA of the hydrated series. (Exceptions include 2-hydroxy-4,6,7-trimethyl-, 6-hydroxy-7-methyl-, and 4,6-dihydroxy-pteridine, where the neutral solution contains comparable amounts of hydrated and anhydrous species. In such cases, rapid potentiometric titrations show two well-defined and separated curves, one for the hydrated, the other for the anhydrous, species.) Similarly, from solutions of the anion, an approximate pA value for the anhydrous species is obtained. For convenience, the anhydrous molecule is referred to as HX, its anion as X , the hydrated neutral molecule as HY, and its anion as Y, and the two equilibrium constants are defined as follows ... 

Potentiometric titration curves The procedure involves the addition of a salt of a weak acid to the resin and the determination of the pH of the equilibrated solution. Table 9 shows the pK values of the OH groups and dissociation constants of the studied resin. The first ionization occurs at a pH slightly higher than that of sul-... 

The first comprehensive investigation of the TaF5 - HF - H2O system was performed by Buslaev and Nikolaev [292]. Based on the analysis of solubility isotherms, and on conductometric and potentiometric titrations, the authors concluded that in this solution, tantalum forms oxyfluorotantalic acid, H2TaOF5, similar to the formation of H NbOFs in solutions containing NbF5. 

For the primary stage (phosphoric) V) acid as a monoprotic acid), methyl orange, bromocresol green, or Congo red may be used as indicators. The secondary stage of phosphoric) V) acid is very weak (see acid Ka = 1 x 10 7 in Fig. 10.4) and the only suitable simple indicator is thymolphthalein (see Section 10.14) with phenolphthalein the error may be several per cent. A mixed indicator composed of phenolphthalein (3 parts) and 1-naphtholphthalein (1 part) is very satisfactory for the determination of the end point of phosphoric(V) acid as a diprotic acid (see Section 10.9). The experimental neutralisation curve of 50 mL of 0.1M phosphoric(V) acid with 0.1M potassium hydroxide, determined by potentiometric titration, is shown in Fig. 10.6. 

In acid-base titrations the end point is generally detected by a pH-sensitive indicator. In the EDTA titration a metal ion-sensitive indicator (abbreviated, to metal indicator or metal-ion indicator) is often employed to detect changes of pM. Such indicators (which contain types of chelate groupings and generally possess resonance systems typical of dyestuffs) form complexes with specific metal ions, which differ in colour from the free indicator and produce a sudden colour change at the equivalence point. The end point of the titration can also be evaluated by other methods including potentiometric, amperometric, and spectrophotometric techniques. 

The indicator electrode employed in a potentiometric titration will, of course, be dependent upon the type of reaction which is under investigation. Thus, for an acid-base titration, the indicator electrode is usually a glass electrode (Section 15.6) for a precipitation titration (halide with silver nitrate, or silver with chloride) a silver electrode will be used, and for a redox titration [e.g. iron(II) with dichromate] a plain platinum wire is used as the redox electrode. 

Pyrolusite. Dissolve 1.5-2 g, accurately weighed, pyrolusite in a mixture of 25 mL of 1 1 hydrochloric acid and 6 mL concentrated sulphuric add, and dilute to 250 mL. Filtration is unnecessary. Titrate an aliquot part containing 80-100 mg manganese add 200 mL freshly prepared, saturated sodium pyrophosphate solution, adjust the pH to a value between 6 and 7, and perform the potentiometric titration as described above. 

---