Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Saturated Sodium

Sf values converted from Cordfunke, E. H. P. and R. J. M. Konings, Thermochemical Data for Reactor Materials and Fission Products, North Holland Elsevier, NY, 1990. sg determined as. sy+ (hg — hfj/T. lg and kg values estimated by P. E. Liley. All other values are from Fink, J. K. and L. Leibowitz, Argonne Nat. Lab Rept. ANL/RE-95-2, 1995. The Fink and Leibowitz work also appeared in High Temp. Materials Sci., 35, 65-103,1996. Saturation and superheat tables and a diagram to 14 bar, 1700 K are given by Reynolds, W. C., Thermodynamic Properties in S.L, Stanford Univ. publ., 1979 (173 pp.). For a Mollier diagram for 0.1-150 psia, 1500-2700 °R, see Weatherford, P. M., J. C. Tyler, et ah, WADD-TR-61-96, 1961. [Pg.401]


This type of extraction depends upon the use of a reagent which reacts chemically with the compound to be extracted, and is generally employed either to remove small amounts of impurities in an organic compound or to separate the components of a mixture. Examples of such reagents include dilute (5 per cent.) aqueous sodium or potassium hydroxide solution, 5 or 10 per cent, sodium carbonate solution, saturated sodium bicarbonate solution (ca. 5 per cent.), dilute hydrochloric or sulphuric acid, and concentrated sulphuric acid. [Pg.151]

Add 0-5-1 ml. of the alcohol, cork the flask loosely, and heat on a water bath for 10 minutes secondary and tertiary alcohols require longer heating (up to 30 minutes). Cool the mixture, add 10 ml. of 5 per cent, (or saturated) sodium bicarbonate solution, break up the resulting solid ester with a stirring rod (alternatively, stir until crystalline), and filter at the pump wash with a little sodium bicarbonate solution, followed by water, and then suck as dry as possible. Dissolve the crude... [Pg.262]

In a 1500 ml. round-bottomed flask, carrying a reflux condenser, place 100 g. of pure cydohexanol, 250 ml. of concentrated hydrochloric acid and 80 g. of anhydrous calcium chloride heat the mixture on a boiling water bath for 10 hours with occasional shaking (1). Some hydrogen chloride is evolved, consequently the preparation should be conducted in the fume cupboard. Separate the upper layer from the cold reaction product, wash it successively with saturated salt solution, saturated sodium bicarbonate solution, saturated salt solution, and dry the crude cycZohexyl chloride with excess of anhydrous calcium chloride for at least 24 hours. Distil from a 150 ml. Claisen flask with fractionating side arm, and collect the pure product at 141-5-142-5°. The yield is 90 g. [Pg.275]

In a 500 ml. three-necked flask, equipped with a thermometer, a sealed Hershberg stirrer and a reflux condenser, place 32-5 g. of phosphoric oxide and add 115-5 g. (67-5 ml.) of 85 per cent, orthophosphoric acid (1). When the stirred mixture has cooled to room temperature, introduce 166 g. of potassium iodide and 22-5 g. of redistilled 1 4-butanediol (b.p. 228-230° or 133-135°/18 mm.). Heat the mixture with stirring at 100-120° for 4 hours. Cool the stirred mixture to room temperature and add 75 ml. of water and 125 ml. of ether. Separate the ethereal layer, decolourise it by shaking with 25 ml. of 10 per cent, sodium thiosulphate solution, wash with 100 ml. of cold, saturated sodium chloride solution, and dry with anhydrous magnesium sulphate. Remove the ether by flash distillation (Section 11,13 compare Fig. II, 13, 4) on a steam bath and distil the residue from a Claisen flask with fractionating side arm under diminished pressure. Collect the 1 4-diiodobutane at 110°/6 mm. the yield is 65 g. [Pg.284]

Prepare 10 ml. of saturated sodium bisulphite solution and add 4 ml. of the aldehyde shake thoroughly and observe the rise in temperature. Filter the crystalline precipitate at the pump, wash it with a little alcohol, followed by ether, and allow it to dry. [Pg.332]

The method is generally applicable when other modes of esterification are either slow, inefficient, or likely to cause isomerisation it is, however, time-consuming and expensive. Small quantities of acid impurities are sometimes produced, hence it is advisable to wash the ester with saturated sodium bicarbonate solution. The silver salt can usually be prepared by dissolving the acid in the calculated quantity of standard ammonium hydroxide solution and... [Pg.381]

Ethyl n-butyrate. Use a mixture of 88 g. (92 ml.) of n-butyric acid, 23 g. (29 ml.) of ethanol and 9 g. (5 ml.) of concentrated sulphuric acid. Reflux for 14 hours. Pour into excess of water, wash several times with water, followed by saturated sodium bicarbonate solution until all the acid is removed, and finally with water. Dry with anhydrous magnesium sulphate, and distU. The ethyl n-but3rrate passes over at 119 5-120-5°, Yield 40 g. An improved yield can be obtained by distilhng the reaction mixture through an efficient fractionating column until the temperature rises to 125°, and purifying the crude ester as detailed above under methyl acetate. [Pg.383]

Into a 250 or 500 ml. round-bottomed flask provided with a reflux condenser place 46 g. (38 ml.) of A.R. formic acid (98/100 per cent.) and 37 g. (46 ml.) of n-butyl alcohol. Reflux for 24 hours. Wash the cold mixture with small volumes of saturated sodium chloride solution, then with saturated sodium bicarbonate solution in the presence of a httle... [Pg.384]

Place 100 g. of adipic acid in a 750 ml. round-bottomed flask and add successively 100 g. (127 ml.) of absolute ethyl alcohol, 250 ml. of sodium-dried benzene and 40 g. (22 ml.) of concentrated sulphuric acid (the last-named cautiously and with gentle swirling of the contents of the flask). Attach a reflux condenser and reflux the mixture gently for 5-6 hours. Pour the reaction mixture into excess of water (2-3 volumes), separate the benzene layer (1), wash it with saturated sodium bicarbonate solution until eflfervescence ceases, then with water, and dry with anhydrous magnesium or calcium sulphate. Remove most of the benzene by distillation under normal pressure until the temperature rises to 100° using the apparatus of Fig. II, 13, 4 but substituting a 250 ml. Claisen flask for the distilling flask then distil under reduced pressure and collect the ethyl adipate at 134-135°/17 mm. The yield is 130 g. [Pg.386]

Method B. Reflux a mixture of 101 g. of sebacic acid, 196 g. (248 ml.) of absolute ethjd alcohol and 20 ml. of concentrated sulphuric acid for 12 hours. Distil oft about half of the alcohol on a water bath dilute the residue with 500-750 ml. of water, remove the upper layer of crude ester, and extract the aqueous layer with ether. Wash the combined ethereal extract and crude ester with water, then with saturated sodium bicarbonate solution until effervescence ceases, and finally with water. Dry with anhydrous magnesium or sodium sulphate, remove the ether on a water bath, and distil the residue under reduced pressure. B.p. 155-157°/6 mm. Yield llOg. [Pg.387]

Place a mixture of 25 5 g. of n-valerio acid (Sections 111,83 and 111,84), 30 g. (37 -5 ml.) of dry n-propyl alcohol, 50 ml. of sodium-dried benzene and 10 g. (5-5 ml.) of concentrated sulphuric acid in a 250 ml. round-bottomed flask equipped with a vertical condenser, and reflux for 36 hours. Pour into 250 ml. of water and separate the upper layer. Extract the aqueous layer with ether, and add the extract to the benzene solution. Wash the combined extracts with saturated sodium bicarbonate solution until effervescence ceases, then with water, and dry with anhydrous magnesium sulphate. Remove the low boiling point solvents by distillation (use the apparatus of Fig. II, 13,4 but with a Claisen flask replacing the distilling flask) the temperature will rise abruptly and the fi-propyl n-valerate will pass over at 163-164°. The yield is 28 g. [Pg.387]

The iso-nitrile may be removed by the following procedure. Shake the crude (undistilled) n-butyl cyanide twice with about half its volume of concentrated hydrochloric acid and separate carefully after each washing then wash successively with water, saturated sodium bicarbonate solution and water. Dry with anhydrous calcium chloride or anhydrous calcium sulphate, and distil. Collect the pure n-butyl cyanide at 139-141°. If a fraction of low boiling point is obtained (because of incomplete drying), dry it again with anhydrous calcium sulphate and redistil. The yield is 95 g. [Pg.409]

Pour the resulting dark reddish-brown liquid into 500 ml. of water to which 17 ml. of saturated sodium bisulphite solution has been added (the latter to remove the excess of bromine). Steam distil the resulting mixture (Fig. II, 41,1) , collect the first portion of the distillate, which contains a little unchanged nitrobenzene, separately. Collect about 4 litres of distillate. Filter the yellow crystalline solid at the pump, and press well to remove the adhering liquid. The resulting crude m-bromonitrobenzene, m.p. 51-52°, weighs 110 g. If required pure, distil under reduced pressure (Fig. II, 19, 1) and collect the fraction of b.p. 117-118°/9 mm. it then melts at 56° and the recovery is about 85 per cent. [Pg.537]

This product is sufficiently pure for the preparation of phenylacetic acid and its ethyl ester, but it contains some benzyl tso-cyanide and usually develops an appreciable colour on standing. The following procedure removes the iso-cyanide and gives a stable water-white compound. Shake the once-distilled benzyl cyanide vigorously for 5 minutes with an equal volume of warm (60°) 60 per cent, sulphuric acid (prepared by adding 55 ml. of concentrated sulphuric acid to 100 ml. of water). Separate the benzyl cyanide, wash it with an equal volume of sa+urated sodium bicarbonate solution and then with an equal volume of half-saturated sodium chloride solution- Dry with anhydrous magnesium sulphate and distil under reduced pressure. The loss in washing is very small (compare n-Butyl Cyanide, Section 111,113, in which concentrated hydrochloric acid is employed). [Pg.761]

Dimethyl sulphate may be purified (a) by allowing it to stand over anhydrous potassium carbonate until it is neutral to Congo red paper, or (6) by washing, just before use, with an equal volume of ice water, followed by one-third of its volume of cold, saturated sodium bicarbonate solution. [Pg.804]

Propiophenone. Prepare a solution of diphenyl-cadmium in 110 ml. of dry benzene using 4 9 g. of magnesium, 32 4 g. of bromobenzene and 19 5 g. of anhydrous cadmium chloride. Cool the solution to 10°, and add during 3 minutes a solution of 14 -8 g. of propionyl chloride (b.p. 78-79°) in 30 ml. of dry benzene use external coohng with an ice bath to prevent the temperature from rising above 40°. Stir the mixture for 2 hours at 25-35°. Work up the product as detailed above except that 6 per cent, sodium carbonate solution should replace the saturated sodium bicarbonate solution. The yield of propiophenone, b.p. 100-102°/16 mm., is 17 6 g. [Pg.937]

Myristic acid from hexanoic acid and methyl hydrogen sebacate). Dissolve 23 -2 g. of redistilled hexanoic acid (re caproic acid), b.p. 204-6-205-5°/760 mm., and 21-6 g. of methyl hydrogen sebacate in 200 ml. of absolute methanol to which 0 13 g. of sodium has been added. Electrolyse at 2 0 amps., whilst maintaining the temperature between 30° and 40°, until the pH is about 8 0 (ca. 6 hours). Neutralise the contents of the electrolysis cell with a little acetic acid and distil off the methyl alcohol on a water bath. Dissolve the residue in 200 ml. of ether, wash with three 50 ml. portions of saturated sodium bicarbonate solution, once with water, dry with anhydrous magnesium sulphate, and distil with the aid of a fractionating column (see under Methyl hydrogen adipate). Collect the re-decane at 60°/10 mm. (3 0 g.), the methyl myristate at 158-160°/ 10 mm. (12 5g.) and dimethyl hexadecane-1 16-dicarboxylate at 215-230°/ 7 mm. (1 -5 g.)... [Pg.940]

The purified commercial di-n-butyl d-tartrate, m.p. 22°, may be used. It may be prepared by using the procedure described under i o-propyl lactate (Section 111,102). Place a mixture of 75 g. of d-tartaric acid, 10 g. of Zeo-Karb 225/H, 110 g. (136 ml.) of redistilled n-butyl alcohol and 150 ml. of sodium-dried benzene in a 1-litre three-necked flask equipped with a mercury-sealed stirrer, a double surface condenser and an automatic water separator (see Fig. Ill, 126,1). Reflux the mixture with stirring for 10 hours about 21 ml. of water collect in the water separator. FUter off the ion-exchange resin at the pump and wash it with two 30-40 ml. portions of hot benzene. Wash the combined filtrate and washings with two 75 ml. portions of saturated sodium bicarbonate solution, followed by lOu ml. of water, and dry over anhydrous magnesium sulphate. Remove the benzene by distillation under reduced pressure (water pump) and finally distil the residue. Collect the di-n-butyl d-tartrate at 150°/1 5 mm. The yield is 90 g. [Pg.952]

In a 500 ml. bolt-head flask provided with a thermometer (reaching almost to the bottom) and a calcium chloride (or cotton wool) guard tube, place 100 g. of a-bromo-wo-valerj l bromide and 50 g. of dry, finely-divided urea. Start the reaction by warming the flask on a water bath the temperature soon rises to about 80°. Maintain this temperature for about 3 horns the mass will liquefy and then resolidify. Transfer the sticky reaction product to a large beaker containing saturated sodium bicarbonate solution, stir mechanically and add more saturated sodium bicarbonate solution in small quantities until effervescence ceases. Filter at the pump, suck as dry as possible and dry the crude bromural upon filter paper in the air. RecrystaUise the dry product from toluene. Alternatively, recrystaUise the moist product from hot water (ca. 700 ml.). The yield of pure brommal, m.p. 154-155°, is 28 g. [Pg.999]

Prepare a saturated solution of sodium sulphide, preferably from the fused technical sodium polysulphide, and saturate it with sulphur the sulphur content should approximate to that of sodium tetrasulphide. To 50 ml. of the saturated sodium tetrasulphide solution contained in a 500 ml. round-bottomed flask provided with a reflux condenser, add 12 -5 ml. of ethylene dichloride, followed by 1 g. of magnesium oxide to act as catalyst. Heat the mixture until the ethylene dichloride commences to reflux and remove the flame. An exothermic reaction sets in and small particles of Thiokol are formed at the interface between the tetrasulphide solution and the ethylene chloride these float to the surface, agglomerate, and then sink to the bottom of the flask. Decant the hquid, and wash the sohd several times with water. Remove the Thiokol with forceps or tongs and test its rubber-like properties (stretching, etc.). [Pg.1024]

Bisulphite compounds of aldehydes and ketones. These substances are decomposed by dilute acids into the corresponding aldehydes or ketones with the liberation of sulphur dioxide. The aldehyde or ketone may be isolated by steam distillation or by extraction with ether. Owing to the highly reactive character of aldehydes, the bisulphite addition compounds are best decomposed with saturated sodium bicarbonate solution so um carbonate solution is generally employed for the bisulphite compounds of ketones. [Pg.1079]


See other pages where Saturated Sodium is mentioned: [Pg.172]    [Pg.203]    [Pg.331]    [Pg.382]    [Pg.383]    [Pg.384]    [Pg.385]    [Pg.385]    [Pg.389]    [Pg.445]    [Pg.478]    [Pg.479]    [Pg.540]    [Pg.549]    [Pg.551]    [Pg.569]    [Pg.669]    [Pg.695]    [Pg.704]    [Pg.712]    [Pg.765]    [Pg.782]    [Pg.786]    [Pg.843]    [Pg.877]    [Pg.937]    [Pg.940]    [Pg.941]    [Pg.979]   


SEARCH



© 2024 chempedia.info