Acid-copper lead

The four forms of lead are pure lead, also known as corroding lead (99.94%), common lead (99.94%), chemical lead (99.99) and acid-copper lead (99.99%). The resistance of lead to sulfuric acid enables its use in batteries. It is also used as sheet and pipe in buildings. The main use is as a solder material in the electronics industry. 

There are four common grades of lead pure lead, common lead, chemical lead, and acid-copper lead. These grades are covered by ASTM B 29-92, Standard Specification for Refined Lead. Pure lead and chemical lead contain 99.94 % minimum lead, while the latter two contain 99.9 % rninimum. Typical impurities include Bi, Cu, Ag, Fe, Zn, Ni, Sn, and Sb [4]. Higher purity is also available in commercial quantities, like low bismuth low silver pure lead with 99.995 % minimum lead. However, because lead does not possess the level of required mechanical strength for material of construction, and in many cases, it is unable to support its own weight, alloys have been developed to improve its physical and mechanical properties, especially mechanical rigidity. 

As mentioned before, there are four common grades covered by ASTM B 29-92 pure lead, common lead, chemical lead, and acid-copper lead. Pure lead and common lead... 

Tellurium improves the machinability of copper and stainless steel, and its addition to lead decreases the corrosive action of sulfuric acid on lead and improves its strength and hardness. Tellurium is used as a basic ingredient in blasting caps, and is added to cast iron for chill control. Tellurium is used in ceramics. Bismuth telluride has been used in thermoelectric devices. 

The extraction of metal ions depends on the chelating ability of 8-hydroxyquinoline. Modification of the stmcture can improve its properties, eg, higher solubility in organic solvents (91). The extraction of nickel, cobalt, copper, and zinc from acid sulfates has been accompHshed using 8-hydroxyquinohne in an immiscible solvent (92). In the presence of oximes, halo-substituted 8-hydroxyquinolines have been used to recover copper and zinc from aqueous solutions (93). Dilute solutions of heavy metals such as mercury, ca dmium, copper, lead, and zinc can be purified using quinoline-8-carboxyhc acid adsorbed on various substrates (94). 

In addition to domestic production of Frasch and recovered elemental sulfur, U.S. requirements for sulfur are met with by-product sulfuric acid from copper, lead, molybdenum, and zinc smelting operations as well as imports from Canada and Mexico. By-product sulfur is also recovered as sulfur dioxide and hydrogen sulfide (see Sulfurremoval and recovery). 

The principal direct raw materials used to make sulfuric acid are elemental sulfur, spent (contaminated and diluted) sulfuric acid, and hydrogen sulfide. Elemental sulfur is by far the most widely used. In the past, iron pyrites or related compounds were often used but as of the mid-1990s this type of raw material is not common except in southern Africa, China, Ka2akhstan, Spain, Russia, and Ukraine (96). A large amount of sulfuric acid is also produced as a by-product of nonferrous metal smelting, ie, roasting sulfide ores of copper, lead, molybdenum, nickel, 2inc, or others. 

Whenever insoluble anodes are used, the pH of the plating solution decreases along with the metal ion concentration. In some plating baths, a portion of the anodes is replaced with insoluble anodes in order to prevent metal ion buildup or to reduce metal ion concentration. Lead anodes have been used in acid copper sulfate baths, and steel anodes have been used in alkaline plating baths. 

Analyses (%) Chemical Lead Acid Lead Copper Lead... 

To verify the generality of the cyclization of iodopyrazolecarboxylic acids, copper p-phenylbenzoylacetylide was used in the reaction with 3-iodo-l-methylpyra-zole-4-carboxylic acid. The assumed intermediate, alkynylpyrazolylcarboxylic acid, has a distribution of the electron density which is the most favorable for closure of the five-membered cyclic ether. However, the reaction leads only to the 5-lactone (Scheme 120). 

For some non-ferrous metals (copper, lead, nickel) the attack by sulphuric acid is probably direct with the formation of sulphates. Lead sulphate is barely soluble and gives good protection. Nickel and copper sulphates are deliquescent but are gradually converted (if not leached away) into insoluble basic sulphates, e.g. Cu Cu(OH)2)3SO4, and the metals are thus protected after a period of active corrosion. For zinc and cadmium the sulphur acids probably act by dissolution of the protective basic carbonate film. This reforms, consuming metal in the process, redissolves, and so on. Zinc and cadmium sulphates are formed in polluted winter conditions whereas in the purer atmospheres of the summer the corrosion products include considerable amounts of oxide and basic carbonate. ... 

Nitrosylsulphuric acid, and nitrosyl chloride formed as a result of chloride in the water, can cause corrosion in sulphuric acid and lead-chamber plants. Alloying is not generally beneficial in this instance and some elements (such as copper) can increase the corrosion rate. 

Various authors have investigated the relative susceptibility of a variety of metals to attack by the lower fatty acids the results show that magnesium, lead, steel, zinc and cadmium are ail rapidly attacked (Donovan and Stringer for instance, showed that zinc corrodes at a rate of 5 / m per surface per week at 30 C and 1(X)% r.h. in air that contains 0-5 parts per million of acetic acid) copper and nickel are attacked less rapidly, and aluminium, tin and silver are resistant to attack. 

Discussion. The procedure is based on the formation of yellow tetraiodo-antimonate(III) acid (HSbI4) when antimony(III) in sulphuric acid solution is treated with excess of potassium iodide solution. Spectrophotometric measurements may be made at 425 nm in the visible region or, more precisely, at 330 nm in the ultraviolet region. Appreciable amounts of bismuth, copper, lead, nickel, tin, tungstate, and molybdate interfere. 

Many years ago, geochemists recognized that whereas some metallic elements are found as sulfides in the Earth s crust, others are usually encountered as oxides, chlorides, or carbonates. Copper, lead, and mercury are most often found as sulfide ores Na and K are found as their chloride salts Mg and Ca exist as carbonates and Al, Ti, and Fe are all found as oxides. Today chemists understand the causes of this differentiation among metal compounds. The underlying principle is how tightly an atom binds its valence electrons. The strength with which an atom holds its valence electrons also determines the ability of that atom to act as a Lewis base, so we can use the Lewis acid-base model to describe many affinities that exist among elements. This notion not only explains the natural distribution of minerals, but also can be used to predict patterns of chemical reactivity. 

The fluoboric acid may be prepared by adding 92 g. of A.R. boric acid slowly and with constant stirring to 250 g. of hydrofluoric acid (40-48 per cent.) in a copper, lead or a waxed-lined beaker. A lead rod may be used for stirring. All operations should be carried out in a fume cupboard. 

In this cell, the following independent phases must be considered platinum, silver, gaseous hydrogen, solid silver chloride electrolyte, and an aqueous solution of hydrogen chloride. In order to be able to determine the EMF of the cell, the leads must be made of the same material and thus, to simplify matters, a platinum lead must be connected to the silver electrode. It will be seen in the conclusion to this section that the electromotive force of a cell does not depend on the material from which the leads are made, so that the whole derivation could be carried out with different, e.g. copper, leads. In addition to Cl- and H30+ ions (further written as H+), the solution also contains Ag+ ions in a small concentration corresponding to a saturated solution of silver chloride in hydrochloric acid. Thus, the following scheme of the phases can be written (the parentheses enclose the species present in the given phase) ... 

---