Acetone traces

Dissolve I ml. of benzaldehyde and 0-4 ml. of pure acetone in 10 ml. of methylated spirit contained in a conical flask or widemouthed bottle of about 50 ml. capacity. Dilute 2 ml. of 10% aqueous sodium hydroxide solution with 8 ml. of water, and add this dilute alkali solution to the former solution. Shake the mixture vigorously in the securely corked flask for about 10 minutes (releasing the pressure from time to time if necessary) and then allow to stand for 30 minutes, with occasional shaking finally cool in ice-water for a few minutes. During the shaking, the dibenzal -acetone separates at first as a fine emulsion which then rapidly forms pale yellow crystals. Filter at the pump, wash well with water to eliminate traces of alkali, and then drain thoroughly. Recrystallise from hot methylated or rectified spirit. The dibenzal-acetone is obtained as pale yellow crystals, m.p. 112 yield, o 6 g. 

The anhydrous compound is not appreciably hygroscopic, is readily soluble in acetone and amyl alcohol, and insoluble in benzene, toluene, xylene and chloroform it is also readily soluble in absolute methyl or ethyl alcohol, but a trace of water causes immediate hydrolysis with the formation of an opalescent precipitate. 

To obtain maleic acid, evaporate the maleic anhydride with one half of its weight of water on a water bath remove the last traces of water by leaving in a desiccator over concentrated sulphuric acid. The resulting maleic acid has m.p. 143° and is quite pure (1). It may be recrystaUised, if desired, from acetone- light petroleum (b.p. 60-80°) and then melts at 144° (1). 

Hate 3. All glassware used for the work-up and distillation must be rinsed with a dilute solution of triethylamine in diethyl ether or acetone in order to be sure that traces of acids on the glass walls have been neutralized. Allenic sulfides with the structure C=C=C(SR)-CH- isomerize under the influence of acids to give conjugated dienes, C=C-C(SR)=C. 

Aluminous and siliceous residues A 2% hydrofluoric acid solution followed by concentrated sulfuric acid rinse immediately with distilled water followed by a few milliliters of acetone. Repeat rinsing until all trace of acid is removed. 

This somewhat lengthy experiment provides a thorough introduction to the use of GG for the analysis of trace-level environmental pollutants. Sediment samples are extracted by sonicating with 3 X 100-mL portions of 1 1 acetone hexane. The extracts are then filtered and concentrated before bringing to a final volume of 10 mL. Samples are analyzed with a capillary column using a stationary phase of 5% phenylmethyl silicone, a splitless injection, and an EGD detector. 

In current industrial practice gas chromatographic analysis (glc) is used for quahty control. The impurities, mainly a small amount of water (by Kad-Fischer) and some organic trace constituents (by glc), are deterrnined quantitatively, and the balance to 100% is taken as the acetone content. Compliance to specified ranges of individual impurities can also be assured by this analysis. The gas chromatographic method is accurately correlated to any other tests specified for the assay of acetone in the product. Contract specification tests are performed on product to be shipped. Typical wet methods for the deterrnination of acetone are acidimetry (49), titration of the Hberated hydrochloric acid after treating the acetone with hydroxylamine hydrochloride and iodimetry (50), titrating the excess of iodine after treating the acetone with iodine and base (iodoform reaction). 

Suitable catalysts include the hydroxides of sodium (119), potassium (76,120), calcium (121—125), and barium (126—130). Many of these catalysts are susceptible to alkali dissolution by both acetone and DAA and yield a cmde product that contains acetone, DAA, and traces of catalyst. To stabilize DAA the solution is first neutralized with phosphoric acid (131) or dibasic acid (132). Recycled acetone can then be stripped overhead under vacuum conditions, and DAA further purified by vacuum topping and tailing. Commercial catalysts generally have a life of about one year and can be reactivated by washing with hot water and acetone (133). It is reported (134) that the addition of 0.2—2 wt % methanol, ethanol, or 2-propanol to a calcium hydroxide catalyst helps prevent catalyst aging. Research has reported the use of more mechanically stable anion-exchange resins as catalysts (135—137). The addition of trace methanol to the acetone feed is beneficial for the reaction over anion-exchange resins (138). 

The neutralized cleavage product, consisting of acetone, phenol, water, hydrocarbons, and trace organic impurities, is separated in a series of distillation columns. Also in this section alpha-methylstyrene is either recovered as a product or hydrogenated to cumene. 

Other by-products include acetone, carbonaceous material, and polymers of propylene. Minor contaminants arise from impurities in the feed. Ethylene and butylenes can form traces of ethyl alcohol and 2-butanol. Small amounts of / -propyl alcohol carried through into the refined isopropyl alcohol can originate from cyclopropane [75-19-4] in the propylene feed. Acetone, an oxidation product, also forms from thermal decomposition of the intermediate sulfate esters, eg. 

Silver nitrate forms colorless, rhombic crystals. It is dimorphic and changes to the hexagonal rhombohedral form at 159.8°C. It melts at 212°C to a yellowish Hquid which solidifies to a white, crystalline mass on cooling. An alchemical name, lunar caustic, is stiU appHed to this fused salt. In the presence of a trace of nitric acid, silver nitrate is stable to 350°C. It decomposes at 440°C to metallic silver, nitrogen, and nitrogen oxides. Solutions of silver nitrate are usually acidic, having a pH of 3.6—4.6. Silver nitrate is soluble in ethanol and acetone. 

A representative technical grade of methyl chloride contains not more than the following indicated quantities in ppm of impurities water, 100 acid, such as HCl, 10 methyl ether, 20 methanol, 50 acetone, 50 residue, 100. No free chlorine should be detectable. Traces of higher chlorides are generally present in methyl chloride produced by chlorination of methane. The boiling point should be between —24 and —23° C, and 5—95% should distill within a range of about 0.2°C. It should be clear, colorless, and free from visible impurities. 

The apparatus must be flushed with acetylene in order to remove all traces of oxygen. Acetylene dissolved in acetone is most appropriate. Acetylene obtained from tanks which contain solvents such as dimethylformamide (or other solvents) gave lower yields of carbocupration. 

Cellulose for chromatography is purified by sequential washing with chloroform, ethanol, water, ethanol, chloroform and acetone. More extensive purification uses aqueous ammonia, water, hydrochloric acid, water, acetone and diethyl ether, followed by drying in a vacuum. Trace metals can be removed from filter paper by washing for several hours with O.IM oxalic or citric acid, followed by repeated washing with distilled water. 

Ethanol [64-17-5] M 46.1, b 78.3 , d 0.79360, d 0.78506, n 1.36139, pK 15.93. Usual impurities of fermentation alcohol are fusel oils (mainly higher alcohols, especially pentanols), aldehydes, esters, ketones and water. With synthetic alcohol, likely impurities are water, aldehydes, aliphatic esters, acetone and diethyl ether. Traces of benzene are present in ethanol that has been dehydrated by azeotropic distillation with benzene. Anhydrous ethanol is very hygroscopic. Water (down to 0.05%) can be detected by formation of a voluminous ppte when aluminium ethoxide in benzene is added to a test portion. Rectified... 

Tetramethylammonium chloride [75-57-0] M 109.6, m >230°(dec). Crystd from EtOH, EtOH/CHCl3, EtOH/diethyl ether, acetone/EtOH (1 1), isopropanol or water. Traces of the free amine can be removed by washing with CHCI3. 

Sodium polyacrylate (NaPAA) [9003-04-7]. Commercial polyacrylamide was neutralised with an aqueous solution of NaOH and the polymer ppted with acetone. The ppte was redissolved in a small amount of water and freeze-dried. The polymer was repeatedly washed with EtOH and water to remove traces of low... 

Bisethylenedioxypregn-5-ene. Method A. A mixture of progesterone (10 g), freshly distilled ethylene glycol (80 ml) and benzene (350 ml) is slowly distilled for 15 min to remove traces of water. p-Toluenesulfonic acid monohydrate (0.3 g) is added and the mixture is heated under reflux with stirring for 5 hr with a water separator. Saturated sodium bicarbonate solution is added to the cooled mixture and the benzene layer is separated. The organic layer is washed twice with water, dried and evaporated in vacuo. The residue is crystallized twice from acetone-methanol to give 4.15 g (32%) of bisketal, mp 178-181°. 

Methoxypregna-3,5-dien-20-oned A solution of progesterone (0.3 g) dissolved in 5 ml of 2,2-dimethoxypropane-dimethylformamide (1 1) is treated with p-toluenesulfonic acid monohydrate (8 mg) and 0.1 ml of methanol and then heated under reflux for 3.5 hr. The cooled solution is neutralized with 45 mg of sodium bicarbonate, dissolved in 200 ml of ice water, stirred for 0.5 hr and filtered. The enol ether thus obtained (0.29 g, 92%) is purified by crystallization from acetone-methanol containing a trace of pyridine mp 135-160° [a]o —61° (CHCI3). 

---