Acetals peracetates

Acetic acid Acetic anhydride, chloroacetic acid, ethyl acetate, peracetic acid, vinyl acetate, cellulose acetate, terephthalic acid Food additives, solvent, monomers, resin Cheryan etal., 1997 Ravinder etal., 2000 Patel etal., 2006... 

A stirred mixture of phenylmercuric acetate, peracetic and acetic acids together with iodobenzene at 75 C for 4 hours gave phenyl acetate in 75% yield. The corresponding tin, thallium, cadmium and lead compounds were reported to behave similarly (ref.3). 

Peracetic acid and formaldehyde are the expected ozonolysis products for acetone enol (6), and they are obtained in roughly equimolecular ratio. Infrared spectra cannot be used to identify them since peracetic acid in propan-2-ol absorbs at 1755 cm. , coinciding with a minor solvent peak, while formaldehyde monomer would presumably exist as hemi-acetal. Peracetic acid does not survive gas chromatography at 40 °C. on a polypropylene oxide/glycerol condensate (GPO-50)-glutaric acid phase. However, the peracid titer partitioned between trichlorofluoro-... 

Acetaldehyde is an important intermediate in the production of acetic acid, acetic anhydride, ethyl acetate, peracetic acid, pentaerythritol, chloral, glyoxal, and alkylamines. Acetaldehyde is also a valuable intermediate in the manufacture of dyes, pharmaceuticals, pyridine derivatives, and other chemical products. 

Monochloroacetic Acid Glycolic Acid Hydroxyacetic Acid Methyl Acetate Peracetic Acid Acetylene Tetrabromide 1,1/2,2-Tetrabromoethane Isobutyric Acid 2-Methylpropanoic Acid... 

Diphenic acid. Phenanthrene upon oxidation in acetic acid solution at 85° with 30 per cent, hydrogen peroxide gives diphenic acid (diphenyl-2 2 -di-carboxyHc acid) no phenanthraquinone is formed under these experimental conditions. The reaction is essentially an oxidation of phenanthrene with peracetic acid. (For another method of preparation, see Section I V,74.)... 

The epoxides may be converted into 1 2-glycols by hydrolysis. In some cases the 1 2-glycol may be produced directly by carrying out the epoxidation in the presence of water. If the 1 2-glycol is desired, it is usually better to employ performic acid or peracetic acid, the latter best in the presence of a trace of sulphuric acid. An epoxide is first formed, followed by the hydroxy-formate or hydroxy-acetate, and ultimately the 1 2-glycol ... 

Acetaldehyde, first used extensively during World War I as a starting material for making acetone [67-64-1] from acetic acid [64-19-7] is currendy an important intermediate in the production of acetic acid, acetic anhydride [108-24-7] ethyl acetate [141-78-6] peracetic acid [79-21 -0] pentaerythritol [115-77-5] chloral [302-17-0], glyoxal [107-22-2], aLkylamines, and pyridines. Commercial processes for acetaldehyde production include the oxidation or dehydrogenation of ethanol, the addition of water to acetylene, the partial oxidation of hydrocarbons, and the direct oxidation of ethylene [74-85-1]. In 1989, it was estimated that 28 companies having more than 98% of the wodd s 2.5 megaton per year plant capacity used the Wacker-Hoechst processes for the direct oxidation of ethylene. 

Oxidation. Acetaldehyde is readily oxidised with oxygen or air to acetic acid, acetic anhydride, and peracetic acid (see Acetic acid and derivatives). The principal product depends on the reaction conditions. Acetic acid [64-19-7] may be produced commercially by the Hquid-phase oxidation of acetaldehyde at 65°C using cobalt or manganese acetate dissolved in acetic acid as a catalyst (34). Liquid-phase oxidation in the presence of mixed acetates of copper and cobalt yields acetic anhydride [108-24-7] (35). Peroxyacetic acid or a perester is beheved to be the precursor in both syntheses. There are two commercial processes for the production of peracetic acid [79-21 -0]. Low temperature oxidation of acetaldehyde in the presence of metal salts, ultraviolet irradiation, or osone yields acetaldehyde monoperacetate, which can be decomposed to peracetic acid and acetaldehyde (36). Peracetic acid can also be formed directiy by Hquid-phase oxidation at 5—50°C with a cobalt salt catalyst (37) (see Peroxides and peroxy compounds). Nitric acid oxidation of acetaldehyde yields glyoxal [107-22-2] (38,39). Oxidations of /)-xylene to terephthaHc acid [100-21-0] and of ethanol to acetic acid are activated by acetaldehyde (40,41). 

Figure 3 shows the production of acetaldehyde in the years 1969 through 1987 as well as an estimate of 1989—1995 production. The year 1969 was a peak year for acetaldehyde with a reported production of 748,000 t. Acetaldehyde production is linked with the demand for acetic acid, acetic anhydride, cellulose acetate, vinyl acetate resins, acetate esters, pentaerythritol, synthetic pyridine derivatives, terephthaHc acid, and peracetic acid. In 1976 acetic acid production represented 60% of the acetaldehyde demand. That demand has diminished as a result of the rising cost of ethylene as feedstock and methanol carbonylation as the preferred route to acetic acid (qv). 

The nameplate capacities for acetaldehyde production for the United States in 1989 are shown in Table 5 (120). Synthetic pyridine derivatives, peracetic acid, acetate esters by the Tischenko route, and pentaerythritol account for 40% of acetaldehyde demand. This sector may show strong growth in some products but all of these materials maybe prepared from alternative processes. 

About half of the wodd production comes from methanol carbonylation and about one-third from acetaldehyde oxidation. Another tenth of the wodd capacity can be attributed to butane—naphtha Hquid-phase oxidation. Appreciable quantities of acetic acid are recovered from reactions involving peracetic acid. Precise statistics on acetic acid production are compHcated by recycling of acid from cellulose acetate and poly(vinyl alcohol) production. Acetic acid that is by-product from peracetic acid [79-21-0] is normally designated as virgin acid, yet acid from hydrolysis of cellulose acetate or poly(vinyl acetate) is designated recycle acid. Indeterrninate quantities of acetic acid are coproduced with acetic anhydride from coal-based carbon monoxide and unknown amounts are bartered or exchanged between corporations as a device to lessen transport costs. 

By-product acetic acid is obtained chiefly from partial hydrolysis of cellulose acetate [9004-35-7]. Lesser amounts are obtained through the reaction of acetic anhydride and cellulose. Acetylation of saHcyHc acid [69-72-7] produces one mole of acetic acid per mole of product and the oxidation of allyl alcohol using peracetic acid to yield glycerol furnishes by-product acid, but the net yield is low. 

Dibromoacetic acid [631-64-1] (Br2CHCOOH), mol wt 217.8, C2H2Br202, mp 48°C, bp 232—234°C (decomposition), is soluble in water and ethyl alcohol. It is prepared by adding bromine to boiling acetic acid, or by oxidi2ing tribromoethene [598-16-3] with peracetic acid. 

Medroxyprogesterone acetate (74) is stmcturaHy related to and has been prepared from hydroxyprogesterone (39) (Fig. 10). Formation of the bis-ketal accomplishes the protection of the ketones and the required migration of the double bond. Epoxidation with peracetic acid produces a mixture of epoxides (75), with a predominating. Treatment of the a-epoxide with methyl magnesium bromide results in diaxial opening of the epoxide. Deprotection of the ketones provides (76), which is dehydrated to (77) by treatment with dilute sodium hydroxide in pyridine. Upon treatment with gaseous hydrochloric... 

Another method of preparing mercuric acetate is the oxidation of mercury metal using peracetic acid dissolved in acetic acid. Careful control of the temperature is extremely important because the reaction is quite exothermic. A preferred procedure is the addition of approximately half to two-thirds of the required total of peracetic acid solution to a dispersion of mercury metal in acetic acid to obtain the mercurous salt, followed by addition of the remainder of the peracetic acid to form the mercuric salt. The exothermic reaction is carried to completion by heating slowly and cautiously to reflux. This also serves to decompose excess peracid. It is possible and perhaps more economical to use 50% hydrogen peroxide instead of peracetic acid, but the reaction does not go quite as smoothly. 

Peracetic acid then reacts with propylene at 320—350 K and 1.00—1.34 MPa (10—13.2 atm), forming propylene oxide and acetic acid. 

Although this process has not been commercialized, Daicel operated a 12,000-t/yr propylene oxide plant based on a peracetic acid [79-21-0] process during the 1970s. The Daicel process involved metal ion-catalyzed air oxidation of acetaldehyde in ethyl acetate solvent resulting in a 30% peracetic acid solution in ethyl acetate. Epoxidation of propylene followed by purification gives propylene oxide and acetic acid as products (197). As of this writing (ca 1995), this process is not in operation. 

Fig. 2. Synthesis of uma2enil (18). The isonitrosoacetanihde is synthesized from 4-f1iioroani1ine. Cyclization using sulfuric acid is followed by oxidization using peracetic acid to the isatoic anhydride. Reaction of sarcosine in DMF and acetic acid leads to the benzodiazepine-2,5-dione. Deprotonation, phosphorylation, and subsequent reaction with diethyl malonate leads to the diester. After selective hydrolysis and decarboxylation the resulting monoester is nitrosated and catalyticaHy hydrogenated to the aminoester. Introduction of the final carbon atom is accompHshed by reaction of triethyl orthoformate to...

Peracids are also available as aqueous solutions that contain the peracid in equihbrium with hydrogen peroxide and the parent acid. Peracetic acid [79-21-0] is commercially available as a 40% solution in dilute acetic acid. The water and dilution of the peracid make these solutions easier to handle than their sohd counterparts, but they still require careful handling and protection from heat. 

Peracetic Acid. Peracetic acid (peroxyacetic acid) [79-21-0] the peroxide of acetic acid, is a disinfectant having the desirable properties... 

The ease of oxidation varies considerably with the nature and number of ring substituents thus, although simple alkyl derivatives of pyrazine, quinoxaline and phenazine are easily oxidized by peracetic acid generated in situ from hydrogen peroxide and acetic acid, some difficulties are encountered. With unsymmetrical substrates there is inevitably the selectivity problem. Thus, methylpyrazine on oxidation with peracetic acid yields mixtures of the 1-and 4-oxides (42) and (43) (59YZ1275). In favourable circumstances, such product mixtures may be separated by fractional crystallization. Simple alkyl derivatives of quinoxalines are... 

Surprisingly, there are very few examples of successful fV-oxidation of pyrazoles. Simple fV-alkylpyrazoles generally do not react with peracids (B-76MI40402,77JCS(P1)672). The only two positive results are the peracetic acid (hydrogen peroxide in acetic acid) transformation of 1-methylpyrazoIe into 1-methylpyrazole 2-oxide (268) in moderate yield and the peroxy-trifluoroacetic acid (90% hydrogen peroxide in trifluoroacetic acid) transformation of 5-amino-l-methylpyrazoIe into l-methyl-5-nitropyrazoIe 2-oxide (269). 

Methylpyridine-l-oxide has been prepared by the oxidation of 3-methylpyridine with hydrogen peroxide in glacial acetic acid, with 40% peracetic acid and sodium acetate, and with per benzoic acid in benzene. ... 

Pentyl amine, see n-Amylamine Iso-Pentyl nitrite, see Amyl nitrite Peracetic acid (40% acetic acid solution)... 

Mt iliyliiiiLiiic-, Anhydrous 74-89-5 1000 Peracetic Acid (concentration greater than 60% Acetic Acid also called Peroxyacetic Acid) 79-2I- 1 i i t... 

Commercial 40% peracetic acid (containing 1% sulfuric acid) may be employed for this reaction. However, it is necessary to neutralize the sulfuric acid with sodium or potassium acetate to prevent further reactions. 

A solution of 17-cyanoandrosta-5,16-dien-3jS-ol acetate (46 g) and anhydrous potassium acetate (0.46 g) in methylene dichloride (310 ml) is treated with a mixture of 40% peracetic acid (37 ml) and anhydrous potassium acetate (1.84 g) in methylene dichloride (46 ml), the temperature of the solution being maintained below 25°. The mixture is stored at room temperature for 4 hr and then washed successively with water, 5% sodium bicarbonate solution (aqueous sodium bisulfite, 10g/150g water, has been used to decompose excess reagent before workup) and water until neutral. Evaporation of the dried solution and addition of ether gives 24.1 g of 5oc,6a-epoxy-17-cyanoandrost-16-en-3 -ol acetate mp 187-190°. One recrystallization from methanol gives 20.4 g of oxirane melting at 191-194°. 

Epoxidation of the A -enol acetate was originally carried out with per-benzoic acid. Monoperphthalic acid has also been used, but is apparently more susceptible to steric and conformational factors. The commercially available peracetic acid is generally most convenient. Based on the expected backside attack, the derived epoxides have the 17a configuration, and hydrolysis always produces the 17a-hydroxy group. 

Hydrolysis of the intermediate epoxy acetate is generally carried out with strong alkali if base-sensitive groups are present, milder conditions (e.g., potassium bicarbonate, potassium carbonate) can be employed. If commercial peracetic acid (which contains sulfuric acid) is used for epoxidation, the intermediate epoxy acetate cannot be isolated, but is hydrolyzed in situ by the acid to the desired ketol. Acid hydrolysis will also retain 3-acetates, if present. ... 

Oxidation of 4-methylquinoxalin-3-one 2-carboxy-fV -methylamlide (45) with hydrogen peroxide and acetic acid furnishes the 1-oxide but, on removal of either or both of the fV-raethyl groups (giving 46, 47, or 48), oxidation with hydrogen peroxide or with peracetic or perbenzoic acid results in the removal of the carboxyamide groups and the formation of a quinoxaline-2,3-dione. ... 

Ethylene glycol Peracetic acid Acetic anhydride... 

Preparation of 5a,6a-0xido-17a-Hydroxya//opregnane-3,20-dione 3,20-Bis-(Ethy ene Ketal) A solution was prepared by heating 19.96 g (0.0477 mol) of 17a-hydroxyprogesterone 3,20-bis-(ethylene ketal) and 500 ml of benzene. After the solution was effected the flask was cooled to 5°C and a mixture of 3.68 g (0.0449 mol) of sodium acetate and 174 ml of 40% peracetic acid was added with stirring. The reaction mixture was stirred in the ice bath for 3 hours. The lower peracid layer was separated, diluted with water and extracted twice with benzene. 

As an oxidant, hydrogen peroxide may be used either alone or in the presence of a catalyst. Such reactions are often carried out using acetic acid as a solvent. These latter reactions strictly involve oxidation by peracetic acid and will be dealt with in the next section. 

---