A typical mixture analysis

Some of the quantitative techniques outlined in sections 2.1 and 2.2 will now be applied to a typical mixture analysis problem. Let the problem be to assess the state of mixedness of coloured plastic chips with neutral plastic chips in a sheet of plastic. 

In cases where 2D NMR experiments are insufficient for a complete analysis of anionic surfactant mixtures, LC-NMR may provide better information. Characterisation of fatty alcohol ethoxylate (FAE) based oligomeric surfactants by on-line 2D (GCOSY, TOCSY and Homo 2DJ) stopped-flow HPLC- H NMR has been described [655,656]. The analysis of a typical mixture comprising three components (PEG and PEOs with different end-groups) is shown in Figure 7.34. In this representation, the 111 NMR frequency domain is in the... 

Particles come in all shapes and sizes and in large numbers. Data are presented graphically using histograms, fractional plots, or cumulative plots. These graphs are primarily useful as pictures of the size distribution of the mixture. Table 15.4 gives a typical screen analysis for a 900-g sample. The measured experimental data are the mesh sizes, and the masses of the particles on each of the sieves are the masses of the residuals or fines. The other quantities are calculated. 

Figure 1. Schematic representation of the calcium mass spectrum in (a) natural materials, (b) a Ca- Ca tracer solution used for separating natural mass dependent isotopic fractionation from mass discrimination caused by thermal ionization, and (c) a typical mixture of natiwal calcium and tocer calcium used for analysis. The tracer solution has roughly equal amounts of Ca and Ca. In (c) the relative isotopic abundances are shown with an expanded scale. Note that in the mixed sample, masses 42 and 48 are predominantly from the tracer solution, and masses 40 and 44 are almost entirely from natural calcium. This situation enables the instrumental fractionation to be gauged from the Ca/ Ca ratio, and the natural fractionation to be gauged from the sample Ca/ Ca ratio.

Another typical example of the use of the katherometer in the analysis of gas mixtures is afforded by the separation of the components of the Scott gas mixture 237. This is a standard mixture which consists of a mixture of oxygen, carbon monoxide, methane, and carbon dioxide in an excess of nitrogen. The sample is a typical mixture of gases that are liable to be found in automobile exhaust fumes and is used to test emission analyzing equipment and gas analyses apparatus. An example of such a separation carried out on a proprietary packing at 25°C is shown in figure 5. 

Chloroform/methanol = 2/1 mixtures are commonly used for extraction. Addition of water results in separation of the chloroform layer containing the lipids. Dry lipid mixtures can be extracted with cold dry acetone where the neutral lipids usually dissolve and most of the phospholipids remain behind. At one time such crude processes of extraction combined with distillation and crystalllisation were the only ones available and were generally inadequate for the separation and characterisation of lipid and phospholipid components. By 1960 however, chromatographic techniques used in conjunction with these processes had enabled good separations of the component lipids to be attained. Chromatographic techniques have been greatly improved since that time and Figure 14.8 shows a typical HPLC analysis of a phospholipid mixture. 

Alkvl Azides from Alkyl Bromides and Sodium Azide General procedure for the synthesis of alkyl azides. In a typical experiment, benzyl bromide (360 mg, 2.1 mmol) in petroleum ether (3 mL) and sodium azide (180 mg, 2.76 mmol) in water (3 mL) are admixed in a round-bottomed flask. To this stirred solution, pillared clay (100 mg) is added and the reaction mixture is refluxed with constant stirring at 90-100 C until all the starting material is consumed, as obsen/ed by thin layer chromatographv using pure hexane as solvent. The reaction is quenched with water and the product extracted into ether. The ether extracts are washed with water and the organic layer dried over sodium sulfate. The removal of solvent under reduced pressure affords the pure alkyl azides as confirmed by the spectral analysis. ... 

For most samples liquid-solid chromatography does not offer any special advantages over liquid-liquid chromatography (LLC). One exception is for the analysis of isomers, where LLC excels. Figure 12.32 shows a typical LSC separation of two amphetamines on a silica column using an 80 20 mixture of methylene chloride and methanol containing 1% NH4OH as a mobile phase. Nonpolar stationary phases, such as charcoal-based absorbents, also may be used. 

Vinyltoluene (VT) is a mixture of meta- and i ra-vinyltoluenes, typically in the ratio of 60 40. This isomer ratio results from the ratio of the corresponding ethyltoluenes in thermodynamic equiHbrium. Physical properties and chemical analysis of a typical vinyltoluene product are shown in Tables 7 and 8, respectively. Vinyltoluene monomer is produced by Dow Chemical Company and Fina Oil Chemical Company. The worldwide consumption is estimated to be approximately 100,000 t/yr. 

Ethyltoluene is manufactured by aluminum chloride-cataly2ed alkylation similar to that used for ethylbenzene production. All three isomers are formed. A typical analysis of the reactor effluent is shown in Table 9. After the unconverted toluene and light by-products are removed, the mixture of ethyltoluene isomers and polyethyltoluenes is fractionated to recover the meta and para isomers (bp 161.3 and 162.0°C, respectively) as the overhead product, which typically contains 0.2% or less ortho isomer (bp 165.1°C). This isomer separation is difficult but essential because (9-ethyltoluene undergoes ring closure to form indan and indene in the subsequent dehydrogenation process. These compounds are even more difficult to remove from vinyltoluene, and their presence in the monomer results in inferior polymers. The o-ethyltoluene and polyethyltoluenes are recovered and recycled to the reactor for isomerization and transalkylation to produce more ethyltoluenes. Fina uses a zeoHte-catalyzed vapor-phase alkylation process to produce ethyltoluenes. 

A typical example of MDGC in environmental analysis is the determination of PCBs. These are ubiquitous contaminants of the environment in which they occur as complex mixtures of many of the 209 theoretically possible congeners. The compositions of environmental mixtures vary according to sample type. 

The refractive index detector, in general, is a choice of last resort and is used for those applications where, for one reason or another, all other detectors are inappropriate or impractical. However, the detector has one particular area of application for which it is unique and that is in the separation and analysis of polymers. In general, for those polymers that contain more than six monomer units, the refractive index is directly proportional to the concentration of the polymer and is practically independent of the molecular weight. Thus, a quantitative analysis of a polymer mixture can be obtained by the simple normalization of the peak areas in the chromatogram, there being no need for the use of individual response factors. Some typical specifications for the refractive index detector are as follows ... 

In a typical run, bis(l,2-diphenylphosphino)ethane (DPPE) (0.022 g, 0.05 mmol) and 1,3 diene (32.5 mmol) are added to a portion of the co-condensate, containing 5.2 mg of rhodium (0.05 mg. atom) in 10 ml of mesitylene. The solution is introduced by suction into an evacuated, 80 ml stainless steel autoclave. Carbon monoxide is introduced to the desired pressure and the autoclave is rocked and heated at 80 °C. Hydrogen is rapidly charged to give 1 1 gas composition. When the pressure reaches the theoretical value corresponding to the desired conversion, the autoclave is cooled, depressurised, and the reaction mixture analyzed by GLC. The crude product is distilled. The aldehydes are obtained as pure samples by preparative GLC and characterized by H NMR spectroscopy and GC-MS analysis. 

---