Vial for injections

Levothyroxine (Synthroid , Levoxyl , Unithroid ), other brands, and generics Synthetic LT4 25, 50, 75, 88, 100, 112, 125, 137, 150, 1 75, 200, and 300 meg tablets 500 meg vial for injection 60 meg Gold standard for treating hypothyroidism products not therapeutically equivalent full replacement dose 1-1.6 meg/kg per day when switching from animal product, lower calculated daily dose by 25-50 meg intravenous form rarely needed... 

Parenteral 12.5 mg/mL in 20 mL vials for injection Dopamine (generic. Intropin)... 

Parenteral 5 mg/vial for injection Prazosin (generic, Minipress)... 

Formulation 50 mg and 100 mg vial for injection (Ambiosome only 50 mg vials)... 

Parenteral 40, 125, 500, 1000, 2000 mg/vial for injection Prednisolone (generic, Delta-Cortef, Prelone)... 

Parenteral 500,000 units per vial for injection Ophthalmic 500,000 units per vial Disinfectants, Antiseptics, Sterilants Benzalkonium (generic, Zephiran)... 

Aqueous solutions (vials for injection) shewed a shelf life of at least two years when examined by high pressure liquid and examined by high pressure liquid and thin layer chranatography.16... 

Acetazolamide (Generic) Diamox (Bausch Lomb) 125- and 250-mg tablets 500-mg sustained-release capsules (Sequels) 500-mg vials for injection... 

Extract again with solvent mixture Evaporate organic layer to dryness Reconstitute residue in 100 pL of methanol Transfer into an autosampler vial for injection... 

Streptokinase doses 100 000-1.5 million units per vial for injection. 

Clinical Use. Vancomycin and teicoplanin as fomiulated dmgs are lyophilized powders to be reconstituted with sterile water for injection. Vancomycin hydrochloride [1404-93-9] is presented in vials of 500 mg that give 100—200 mL solution of pH 2.5—4.2. It is administered by slow (60 min) infusion at a dose of 500 mg every 6 h or 1 g every 12 h/d. The teicoplanin contains the five factors (87%) plus 13% of the pseudoaglycone T-A3-1. It is presented in vials containing 200 mg of lyophili ed power that after dissolution with 3 mL of solvent gives a solution at pH 7.5. The dose regimen is 200—800 mg/d by iv bolus adrninistration. 

Methicillin sodium To reconstitute 1 g vial add 1.5 mL of sterile water for injection or sodium chloride injection. Each reconstituted mL contains approximately 500 mg of methicillin. 

Storage in the same primary container as will be used on the market, e.g., blister strips for tablets or ovules, tubes for creams, or vials and ampules for injectables. 

Several guidelines are available in the literature for the pharmacist who must extemporaneously prepare an ophthalmic solution. The USP contains a section on ophthalmic solutions, as do other compendia and several standard textbooks. Since the pharmacist does not have the facilities to test the product, he or she should dispense only small quantities, with an expiration date of no more than 30 days. Refrigeration of the product should also be required as a precautionary measure. To reduce the largest potential source of microbial contamination, only sterile purified water should be used in compounding ophthalmic solutions. Sterile water for injection, USP, from unopened IV bottles or vials is the highest-quality water available to the pharmacist. Prepackaged sterile water with bacteriostatic agents should not be used. 

CIPROFLOXACIN CONCENTRATE FOR INJECTION 40ML VIAL 60 VIALS/PG 6505013370320 PG 273,40 ... 

POTASSIUM CHLORIDE CONCENTRATE FOR INJECTION USP 20ML VIAL 25/PG 6505010801906 PG 9.99 ... 

THIOPENTAL SODIUM FOR INJECTION USP 500MG VIAL 25 VIALS/PACKAGE 65O5D1G4T0558 PG 178.43 ... 

One millilitre of sediment solution was allowed to stand with O.lmT of the 1% 4-nitro-o-phenylenediamine hydrochloride solution in a 10 mL glass vial for 2h. One millilitre of toluene was added. The vial was capped and shaken vigorously for 2min. One microlitre of the toluene layer was injected into the gas chromatograph. 

Certain medications including penicillins and other antibiotics are unstable when stored in solution form and are therefore packaged in powder form. The dry powders must be reconstituted with a sterile diluent such as sterile water for injection or sterile sodium chloride (normal saline) solution. Instructions supplied with the vial state the volume of diluent which should be added. The resulting volume of the reconstituted drug and the approximate average concentration per milliliter are provided in the label or the package information sheet (package insert). 

The source of polymixin B sulfate is a vial containing 50,000 units of the dry powder. The directions on the vial state Add diluent 9.4 mL (for a) concentration of solution 5000 units per mL. Using water for injection as the diluent, explain how you would obtain the drug needed in compounding the prescription. 

A vial contains 1 g of Ancef (cefazolin sodium). Express the concentrations of cefazolin sodium, in milligrams per milliliter, following reconstitution with sterile water for injection to the following volumes ... 

A 25 mL vial of NaCl solution was diluted to a liter with sterile water for injection. The concentration (w/v) of the NaCl in the finished product was 0.9%. What was the concentration in terms of mEq/mL, of the original solution ... 

PEG-Intron PEG-Intron is used for the treatment of hepatitis C. The product consists of a covalent conjugate of the recombinant interferon- -2b with monomethoxy polyethylene glycol (PEG) supplied in vials with 74/rg, 118.4/rg, 177.6/rg, or 222/rg of the active ingredient and 1.11 mg sodium phosphate (dibasic,anhydrous),l.ll mg sodium phosphate (monobasic, dihydrate), 59.2 mg sucrose, and 0.074mg polysorbate 80. The powder is reconstituted with sterile water-for-injection. 

Mix thoroughly the working sample solution via flask inversion and filter aliquots of the solution through a Whatman 25-mm GD/X 0.45-nm PP membrane syringe filter. Discard the first few milliliters of the filtrate and then transfer the subsequent filtrate into a capped HPLC vial for analysis. Inject 20 J,L of the filtrate into the HPLC. 

---