Using Insert

Polymers are used as inserts for pins and contacts. Important properties of the commonly used insert materials have been compiled (31). Polysulfones are high temperature thermoplastics that have high rigidity, low creep, excellent thermal stabiHty, flame resistance, low loss tangents, and low dielectric constants. The principal weakness of polysulfones is their low chemical resistance. 

This is synthesized by a standard method, while another synthetic method uses insertion reactions ... 

If heat transfer enhancement is only for the inside of the tubes using inserts, then ... 

Lithium ion batteries use insertion processes for both the positive and negative electrodes, leading to the term rocking chair battery. The resulting transport of Li ions between the electrodes, usually... 

Insertion and removal To be sure that the woman is not pregnant at the time of capsule placement and to ensure contraceptive efficacy during the first cycle of use, insert capsules during the first 7 days of the cycle or immediately after an abortion. Insertion is not recommended before 6 weeks postpartum in breast-feeding women. Infection If infection occurs, institute suitable treatment. If infection persists, remove the capsules. 

WilUams, G. V, Rohel, D. Z., Kuzio, J., and Faulkner, P. (1989). A cytopathological investigation of Autographa californica nudear polyhedrosis virus plO gene function using insertion/deletion mutants. J. Gen. Virol. 70, 187-202. 

There are two strategies to use insertional mutagenesis for cloning purposes. One is the direct tagging approach. In this case a mutant, for example a spontaneous or chemically induced mutant, has already been identified, but no information on the nature of the mutated gene is available. 

E. McGee, P. Marjanovic, L. Bates, Modifying flow behaviour in hoppers using inserts and novel wall profiles, Proceedings of the 7th International Conference on Bulk Materials Storage, Handling and Transportation, Newcastle, Australia, October 2001. 

If a section of the suggested table of contents is not used, insert a page behind the tab for that section (see Tabs) and state not applicable in the table of contents and in the text. If a new subsection (line item within a section currently on the table of contents) is added to the table of contents, modify the application accordingly. Additional sections should be placed at the end... 

Palladation of an arene is a very facile reaction when, before the C-H activation step, coordination of palladium to a nearby ligand functionality in the molecule occurs. The first report of a stoichiometric intramolecular palladation is probably the reaction of diazobenzene and palladium chloride by Cope in 1967 [6a], Intramolecular palladation is a widespread reaction that has often been used as a starting point for synthesizing new molecules using insertion reactions in the arylpal-... 

Repeat the ice-point measurements. The results should agree with those obtained previously to within experimental error if the differences are larger, a leak must be suspected. Measure the other fixed points assigned. If liquid nitrogen is used, insert the bulb into the Dewar slowly io prevent violent boiling and excessive loss of liquid. 

Final Directio7is When the apparatus is taken apart, replace the stoppers of the U-tube with corks to preserve the contents for further use. Insert the glass end of the platinum tip into the hole at the smaller... 

Just before use, insert the blasting cap into the cavity made by the rod. The initiator is now ready for use. 

Administration Intranasal Clear nasal passages before use insert spray up into nostril, pointing toward nasal passages away from nasal septum spray into nostril while holding other nostril closed and concurrently inspire through nose to permit medication as high into nasal passages as possible. 

An alternative physical method for fouling control uses inserts within the tubes of a shell and tube exchanger. An example is the Spirelf system that consists of a spiral flexible metal device that is inserted and fixed into the tubes.The action of the device is to vibrate in response to the flow of fluid through the tube in which it is situated, thereby keeping the tube surface clean. The vibration is controlled to avoid erosion of the tube surface. It is claimed that the payback time is low of the order of months. 

Matsuoka, S., Ultrasonic welding of ceramic/metals using inserts, J. Mater. Proc. 

In Excel 97 or later versions, start from the spreadsheet with Alt + F11, then use Insert => Module, File => Import File. The resulting Import File dialog box is equivalent to the Open dialog box in Excel 95, as described above under points (2) and (3). Select the disk or diskette in Look in , and proceed as indicated above. Switch back to the spreadsheet with Alt + F11. 

As a facile method of carbon-carbon bond formation, the insertion of carbon-carbon multiple bonds into carbon-transition-metal bonds is a very important fundamental reaction in organotransition-metal chemistry. However, in contrast to the tremendous number of reports about the insertion of carbon-carbon multiple bonds into carbon-transition-metal bonds, direct insertion of carbon-heteroatom multiple bonds, such as carbonyl and nitrile groups, without using stoichiometric organometallic reagents, has received scant attention.111 A palladium(II)-catalysed cycliza-tion reaction of alkynes with carbon-heteroatom multiple bonds under mild conditions has been developed, using insertion of carbon-heteroatom multiple bonds into the carbon-palladium bond as the key step.[2]... 

---