Urea storage

The SCR-NH3 is a continuous process for NO treatment and shows very efficient treatment efficiency. But this technology needs to put in the vehicle an additional tank for the urea storage. Moreover, this technology is constrained from an architectural point of view because two DOCs are necessary before and after the DeNO catalyst to hydrolyze urea and form ammonia and to prevent the NH3 release in the exhaust line. 

The most important secondary measures include the effective selective catalytic reduction (SCR) and the less effective selective non-catalytic reduction (SNCR). The major drawbacks with SCR are the high capital and operating costs, the large bulky catalytic reactor, NOx/NH3 analytical equipment as well as an ammonia or urea storage and distribution system. SNCR on the other hand has a lower capital cost, but is less effective in NOx reduction. 

Diethyl malonate blocked diisocyanates cross-fink polyols at 120°C for 30 min. The reaction with alcohols does not srield urethanes, rather transesterification occurs (134), and reaction with amines srields amides, not ureas. Storage-stable coatings can be formulated by using monofimctional alcohol in the solvent (135). Clear coats for automobiles that have both excellent environmental etch and abrasion resistance have been formulated with a combination of a hydroxy-functional acrylic resin, malonic ester blocked HDI and IPDI trimers, and an ME resin (136). 

Fig. 1.6 Basic features of the heating system of a urea storage tank [17]...

The NO,OUT A (urea solution) storage tank and skid-mounted module with solution recirculation pumps and heat exchanger for maintaining the solution at 80°F. (Since urea is nontoxic, urea storage requirements are simple.) Separate enhancer storage tanks (unheated) are required if enhancers are used. 

Vapors emitted from the materials of closed storage and exhibit cases have been a frequent source of pollution problems. Oak wood, which in the past was often used for the constmction of such cases, emits a significant amount of organic acid vapors, including formic and acetic acids, which have caused corrosion of metal objects, as well as shell and mineral specimens in natural history collections. Plywood and particle board, especially those with a urea—formaldehyde adhesive, similarly often emit appreciable amounts of corrosive vapors. Sealing of these materials has proven to be not sufficiently rehable to prevent the problem, and generally thek use for these purposes is not considered acceptable practice. 

For production of commercial 50% solution and for recovery of crystalline cyanamide, this process is modified to improve purity and concentration. Calcium and iron may be removed by ion-exchange treatment. The commercial 50% solution is stabilized at pH 4.5—5.0 with 2% monosodium phosphate and contains less than 1.5% dicyandiamide and 0.2% urea. Such solutions are expected to show less than 1% change ia cyanamide content per month of storage below 10°C. It is advisable, however, to adjust the pH periodically duriag extended storage. Organic esters may be used iastead for improved stabihty (23). 

Handling and Storage. Cyanamide solution dimerizes to dicyandiamide and urea with the evolution of heat and a gradual increase in alkalinity accelerating the reaction. Storage above 30°C without pH stabilizer leads to excessive dimerization and can result in violent exothermic polymerization. Cyanamide should be stored under refrigeration and the pH tested periodically. Stabilized cyanamide can be kept at ambient temperature for a few weeks. 

Urea-formaldehyde moulding powders may be moulded without difficulty on conventional compression and transfer moulding equipment. The powders, however, have limited storage life. They should thus be stored in a cool place and, where possible, used within a few months of manufacture. 

The lower cost of the urea-modified PF resins is a combination of PF solids extension by lower cost urea and improved adhesion and distribution capabilities. The improvements in storage stability stem from the thinning and dilution effects as well as from the formaldehyde scavenging. Liquid PF resoles with high free formaldehyde contents tend to be less stable in storage. 

Solid precursor is interesting for storage the tank volume required for a given autonomy will indeed be lower than the tank volume needed to store liquid urea. 

Many methods have been proposed and are used to study the thermal stability of propellants and to ensure the absence of possible autocatalysed decompositions during storage. None are sufficiently reliable to merit individual description. In practice, stabilisers are added, the usual being diphenylamine for nitrocellulose powders and symmetrical diethyl diphenyl urea (carbamate or centralite) for double base propellants. Provided a reasonable proportion of stabiliser remains, the propellant can be assumed to be free from the possibility of autocatalytic decomposition. The best test of stability is therefore a chemical determination of the stabiliser present. 

Polythene containers holding the diisocyanate may harden and burst in prolonged storage, because of slow absorption of water vapour through the wall leading to urea deposition from hydrolysis and generation of pressure of liberated carbon dioxide. 

Tor [7] developed a new method for the preparation of thin, uniform, self-mounted enzyme membrane, directly coating the surface of glass pH electrodes. The enzyme was dissolved in a solution containing synthetic prepolymers. The electrode was dipped in the solution, dried, and drained carefully. The backbone polymer was then cross-linked under controlled conditions to generate a thin enzyme membrane. The method was demonstrated and characterized by the determination of acetylcholine by an acetylcholine esterase electrode, urea by a urease electrode, and penicillin G by a penicillinase electrode. Linear response in a wide range of substrate concentrations and high storage and operational stability were recorded for all the enzymes tested. 

---