Thickness definitions

Minimum exposure times must be observed in order to reach the requisite S/N ratio. As per EN 1435 and EN 584-1, for the different ranges of utilization (energy, wall thickness), definite film elasses are prescribed. They are characterized by the minimum gradient-to-noise ratios. Based on this, one can calculate the minimum values for the S/N ratio based on the IP systems. The exposure time and the device parameter sensitivity and dynamics (latitude) must be adjusted accordingly, with an availability of an at least 12 bit system for the digitalization. 

Most commercial plastic films are produced with a thickness of less than 0.005 in. and most packaging films are less than 0.003 in. Different groups within the different industries (plastic, packaging, aluminum, clothing, etc.) may have their own thickness definitions they call it what their buyer/customer use. Some of them use 0.004 in (0.10 mm) as the dividing line between film and sheet.199... 

The following general classification may be helpful as a guide to film and sheet thickness selection for a die even though different groups within the different industries may have their own thickness definitions as well as their own terminology ... 

The paper presents the results from systematic comparisons of contrast and resolution obtained with different types of radiation sources on steel thicknesses from 5 to 40 mm. These results have been taken into account with the definitions of the European standard for radiographic inspection of weldments (EN 1435) that is approved since 1997. Conclusions from practical investigations on pipe line sites, in petrochcemical plants and in nuclear power stations will be discussed as well. Furthermore, the presentation will stipulate a variety of advantages obtained from the new source in terras of coUimation and radiation protection. 

Other SFA studies complicate the picture. Chan and Horn [107] and Horn and Israelachvili [108] could explain anomalous viscosities in thin layers if the first layer or two of molecules were immobile and the remaining intervening liquid were of normal viscosity. Other inteipretations are possible and the hydrodynamics not clear, since as Granick points out [109] the measurements average over a wide range of surface separations, thus confusing the definition of a layer thickness. McKenna and co-workers [110] point out that compliance effects can introduce serious corrections in constrained geometry systems. 

Thickness. The traditional definition of thermal conductivity as an intrinsic property of a material where conduction is the only mode of heat transmission is not appHcable to low density materials. Although radiation between parallel surfaces is independent of distance, the measurement of X where radiation is significant requires the introduction of an additional variable, thickness. The thickness effect is observed in materials of low density at ambient temperatures and in materials of higher density at elevated temperatures. It depends on the radiation permeance of the materials, which in turn is influenced by the absorption coefficient and the density. For a cellular plastic material having a density on the order of 10 kg/m, the difference between a 25 and 100 mm thick specimen ranges from 12—15%. This reduces to less than 4% for a density of 48 kg/m. References 23—27 discuss the issue of thickness in more detail. 

In use, a mantle of ice is frozen onto the outer surface of the thermometer weU. A common way to do this is to fiU the weU with cmshed dry ice until the mantle achieves a good thickness. Descriptions of the technique for doing this are given in several pubHcations and in manufacturers Hterature. The temperature of the water triple point is 0.01°C, or 273.16 K, by definition. In practice, that temperature can be realized in the ceU within 0.00015 K of the definition. In contrast, a bath of ice and water for producing the temperature 0°C is difficult to estabHsh with an accuracy better than 0.002°C. 

It has been shown (16) that a stable foam possesses both a high surface dilatational viscosity and elasticity. In principle, defoamers should reduce these properties. Ideally a spread duplex film, one thick enough to have two definite surfaces enclosing a bulk phase, should eliminate dilatational effects because the surface tension of an iasoluble, one-component layer does not depend on its thickness. This effect has been verified (17). SiUcone antifoams reduce both the surface dilatational elasticity and viscosity of cmde oils as iUustrated ia Table 2 (17). The PDMS materials are Dow Coming Ltd. polydimethylsiloxane fluids, SK 3556 is a Th. Goldschmidt Ltd. siUcone oil, and FC 740 is a 3M Co. Ltd. fluorocarbon profoaming surfactant. 

Corrosion Resistance. The environment to which a plated part is to be exposed should be a part of any definition of corrosion resistance. Problems arise in testing a part in its intended environment in part because of the long time period required. In many plating processes, corrosion resistance is direcdy proportional to the plate thickness, so a specification on plate thickness is a much faster method of indirectiy measuring corrosion resistance. In specifying a corrosion resistance requirement for the production of plated goods, accelerated tests are used especially if plate thicknesses caimot be related to corrosion protection. 

The burden must have a definite sohdification temperature to assure proper pickup from the feed pan. This limitation can be overcome by side feeding through an auxiliary rotating spreader roll. Apphcation hmits are further extended by special feed devices for burdens having oxidation-sensitive and/or supercoohng characteristics. The standard double-drum model turns downward, with adjustable roll spacing to control sheet thickness. The newer twin-drum model (Fig. ll-55b) turns upward and, though subject to variable cake thickness, handles viscous and indefinite solidification-temperature-point burden materials well. 

The performance of a product where adhesion plays a role is determined both by its adhesive and cohesive properties. In the case of silicones, the promotion of adhesion and cohesion follows different mechanisms [37]. In this context, adhesion promotion deals with the bonding of a silicone phase to the substrate and reinforcement of the interphase region formed at the silicone-substrate interphase. The thickness and clear definition of this interphase is not well known, and in fact depends on many parameters including the surface physico-chemistry of... 

---