Specific leakage

Specific leakage Relating to the leakage that takes place from an enclosure due to a pressure difference created either mechanically or naturally. It is the ratio of leakage area in m divided by the floor area in m. ... 

TABLE 16.1. Organ-Specific Leakage Enzymes Detectable in Scriini/l lasina... 

Kidney Currently, there are no kidney-specific leakage enzymes assayed in serum. Renal function is evaluated by assaying serum levels of nitrogenous wastes—blood urea nitrogen (BUN) and creatinine—and monitoring protein levels in the urine (indicator of glomerular damage). 

Before any remedial or preventive actions are implemented, an evaluation should be conducted as to appHcabiUty to the specific plant. The evaluation should continue while the actions are in progress. The main action should be to take measures to reduce the ingress of contaminants into the steam generator by using more rehable materials, such as in the condenser tubes, to reduce leakage. Contaminant control equipment, such as full-flow condensate deminerali2ers, should also be employed. 

Difficulties with the Na—S system arise ia part from the ceramic nature of the alumiaa separator the specific P-alumiaa is expeasive to prepare and the material is brittie and quite fragile. Separator failure is the leading cause of early cell failure. Cell failure may also be related to performance problems caused by polarization at the sodium/soHd electrolyte iaterface. Lastiy, seal leakage can be a determiaant of cycle life. In spite of these problems, however, the safety and rehabiUty of the Na—S system has progressed to the poiat where pilot plant production of these batteries is anticipated for EV and aerospace apphcations. 

A phenomenon known as silver migration has limited the use of silver plating in miniature circuit boards under a positive d-c potential within a damp environment silver can migrate across insulation. On drying, silver is found in the insulation or media creating a leakage path. Silver plating is forbidden in many military specifications for circuit boards. 

S s, s Cross-sectional area S for minimum cross-sectional area between rows of tubes, flow normal to tubes 5,, for tube-to-baffle leakage area for one baffle for shell-to-baffle area for one baffle for area for flow through window S, g for gross window area S, for window area occupied by tubes Slope of rotary shell Specific gravity of fluid referred to liquid water m fft... 

Companies shipping dangerous materials sometimes build tank cars with metal thicker than required by the specifications in order to reduce the possibihty of leakage during a wreiB or fire. The punching of couplers or rail ends into heads of tanks is a hazard. 

General description. Burnthrough as discussed here specifically refers to the melting of tube metal in the vicinity of the weld such that a cavity is formed. If burnthrough is severe, a continuous channel may be produced that can cause leakage. 

Another method to meet the safety specifications is the use of triple-insulated wire for the secondary windings. Its use can reduce the transformer s size and leakage inductance compared to the border-tape method. Triple-insulated wire has three distinct, approved layers of insulation and it may be wound directly in contact with the primary windings. Whether Mylar tape is needed in or around the transformer depends upon the insulation system used in its construction. This type of transformer can be seen in Figure 3-25. 

Schibbye, 96 Schultz, 426 Seal clearance, 222 Seal leakage, 213 Seal leakage calculations carbon ring, 533 How coefficient, 537 staggered labyrinth, 533 straight labyrinth, 532 Seal oil drainers, 321 Seal oil overhead tank, 319 Seal specification information, 449... 

Improper storage, handling, use or disposal of specific chemicals Leakages Improper venting or draining Open handling Incorrect notification on disposal Use of wrong material... 

Cracking imposes an additional penalty in a vacuum unit in that it forms gas which cannot be condensed at the low pressures employed. This gas must be vented by compressing it to atmospheric pressure. This is accomplished by means of steam jet ejectors. Ideally, it would be possible to operate a vacuum pipe still without ejectors, with the overhead vapors composed only of steam. In practice, however, leakage of air into the system and the minor cracking which occurs make it necessary to provide a means of removing non-condensibles from the system. In addition to the distillation of atmospheric residuum, the lube vacuum pipe still is also used for rerunning of off specification lube distillates. 

Estimate acceptable air leakages resulting from leakage around static and rotary seals, valves, access ports, and other items of mechanical nature required for process operation from the following equations and the specific leak rates 0 indicated in Table 6-8, which is based on w < 10 lb/hr. 

This represents the linear effect of tip speed and the square of impeller size on the flow of a specific impeller. Referring to Figure 12-46, very low flow coefficients for a specific type of centrifugal or axial flow machine cause excessive wall friction or leakage losses, and very high-flow coefficients tend to he subject to turbulence losses due to insufficient flow guiding. ... 

In some hydraulic systems, it is necessary to maintain the system pressure within a specific pressure range for long periods. It is very difficult to maintain a closed system without some leakage, either external or internal. Even a small leak can cause a decrease in pressure. By using an accumulator, leakage can be compensated for and the system pressure can be maintained within acceptable range for extended periods. Accumulators also compensate for thermal expansion and contraction of the liquid due to variations in temperature or generated heat. 

Pressure/vacuum, 435, 466 Vacuum systems, 343 Absolute pressure conversions, 363 Air inleakage, 366 Calculations, 366-375 Dissolved gases release, 368 Estimated air inleakage, table, 366 Evacuation time, 371 Maximum air leakage, chart, 367 Specific air inleakage rates, 368 Temperature approach, 375 Classifications, 343 Diagrams, 380 Pressure drop, 353 Pressure levels, 343, 352 Pressure terminology, 348 Pump down example, 381 Pump down time, 380 Thermal efficiency, 384 Valve codes, 26... 

---