Shavings

If a compound has been recrystallised from petrol, benzene, etc.y some freshly cut shavings of clean paraffin wax should be added to the calcium chloride in (A) or to the sodium hydroxide in D, The surface of the wax absorbs organic solvent vapours (particularly the hydrocarbons) and the last trace of such solvents is thus readily removed from the recrystallised material. 

Drying of crystals. Whenever possible crystals should be dried in a smdl vacuum desiccator containing a suitable desiccant. The latter depends upon the nature of the solvent used c/. p. 19). However for most purposes anhydrous calcium chloride is satisfactory. If a hydrocarbon has been used in the recrystallisation, a few thin fresh shavings of paraffin wax are efficacious. 

Sodium wire, produced with a sodium press (Fig. II, 47, 1), is 6rst collected in sodium-dried ether, the necessary quantity removed, rapidly dried between 61ter paper,and transferred to the flask. Tlirn shavings of sodium, although less satisfactoiy may also be employed, but it is important to avoid undue exposure of the sodium to the atmosphere which produces a surface film of sodium hydroxide. 

Anthracene and maleic anhydride. In a 50 ml. round-bottomed flask fitted with a reflux condenser, place 2 0 g. of pure anthracene, I 1 g. of maleic anhydride (Section 111,93) and 25 ml. of dry xylene. Boil the mixture under reflux for 20 minutes with frequent shaking during the first 10 minutes. Allow to cool somewhat, add 0 5 g. of decolourising carbon and boil for a further 5 minutes. Filter the hot solution through a small, preheated Buchner funnel. Collect the solid which separates upon coohng by suction filtration, and dry it in a vacuum desiccator containing paraffin wax shavings (to absorb traces of xylene). The yield of adduct (colourless crystals), m.p. 262-263° (decomp.), is 2-2 g. Place the product (9 10-dihydroanthracene-9 10-cndo-ap-succinic anhydride) in a weU-stoppered tube, since exposure to air tends to cause hydration of the anhydride portion of the molecule. 

The table below gives the lowest temperature that can be obtained from a mixture of the inorganic salt with finely shaved dry ice. With the organic substances, dry ice (—78°C) in small lumps can be added to the solvent until a slight excess of dry ice remains or liquid nitrogen (—196°C) can be poured into the solvent until a slush is formed that consists of the solid-liquid mixture at its melting point. 

Afterchrome method Afterchrome process After chroming After-shaves Aftertaste... 

Shape anisotropy Shape control Shape factors Shape-memory alloys Shape-selective catalysis Shape selectivity Sharpless catalyst Shaving cream Shaving creams... 

Shaving products Shaw process Shear breeding Shear energy Shearlings Shearometer Shear plane Shear rate Shear stresses Shear test Shear thinning behavior Shear viscosity Sheath-core fiber... 

A, 5A, and 13X zeoHtes are the predorninant adsorbents for CO2 removal by temperature-swing processes. The air fed to an air separation plant must be H2O- and C02-ftee to prevent fouling of heat exchangers at cryogenic temperatures 13X is typically used here. Another appHcation for 4A-type zeoHte is for CO2 removal from baseload and peak-shaving natural gas Hquefaction faciHties. 

The aerosol container has enjoyed commercial success ia a wide variety of product categories. Insecticide aerosols were iatroduced ia the late 1940s. Additional commodities, including shave foams, hair sprays, antiperspirants, deodorants, paints, spray starch, colognes, perfumes, whipped cream, and automotive products, followed ia the 1950s. Mediciaal metered-dose aerosol products have also been developed for use ia the treatment of asthma, migraine headaches, and angiaa. 

Spray shaving creams and furniture poHsh are examples of stable foams. 

Emulsions. Aerosol emulsions (qv) may be oil in water (o/w), such as shaving creams, or water in oil (w/o), such as air fresheners and pohshes. These aerosols consist of active ingredients, an aqueous or nonaqueous vehicle, a surfactant, and a propellant, and can be emitted as a foam or as a spray. 

Quick-breaking foams consist of a miscible solvent system such ethanol (qv) [64-17-5] and water, and a surfactant that is soluble in one of the solvents but not in both. These foams are advantageous for topical appHcation of pharmaceuticals because, once the foam hits the affected area, the foam coUapses, deUvering the product to the wound without further injury from mechanical dispersion. This method is especially usehil for treatment of bums. Some personal products such as nail poHsh remover and after-shave lotion have also been formulated as quick-breaking foams. 

In units designed to use a precoat filter aid, the dmm can be evacuated over the fiiU 360° and fitted with an advancing knife system that continuously shaves off the deposited soHds together with a thin layer of the precoat. The precoat has to be renewed periodically. 

Propylene glycol is also an effective humectant, preservative, and stabilizer and is found in such diverse apphcations as semimoist pet food, bakery goods, food flavorings, salad dressings, and shave creams. Humectancy, or the capabiUty of retaining moisture in a product, is a result of the vapor—Hquid equihbria of the glycol—water system and can be estimated from tables provided by suppHers (27). 

Hydrogen-storage alloys (18,19) are commercially available from several companies in the United States, Japan, and Europe. A commercial use has been developed in rechargeable nickel—metal hydride batteries which are superior to nickel—cadmium batteries by virtue of improved capacity and elimination of the toxic metal cadmium (see BATTERIES, SECONDARYCELLS-ALKALINe). Other uses are expected to develop in nonpolluting internal combustion engines and fuel cells (qv), heat pumps and refrigerators, and electric utility peak-load shaving. 

Nonstabilized foams are referred to as froths froth-bonded fabrics are similar in properties to some saturation-bonded nonwovens. Typical foams used as nonwoven binder solutions have a consistency similar to shaving cream. AppHcation methods include knife-edge layering onto a horizontal web surface followed by vacuum penetration, and saturation and penetration of a vertical web surface using a horizontal-nip pad. Drying and curing is carried out in ovens, dmm dryers, or steam cans. 

Bay Oil. Steam distillation of the leaves of the tree Pimenta racemosa (Mill) which is indigenous to certain islands of the West Indies, particularly Dominica and Puerto Rico, is called bay or bay leaf oil. The same source was used in the past to produce Bay Rum in which mm was distilled over the leaves. Bay oil [8006-78-8] is a yellowish to dark brown mobile Hquid with a fresh-spicy, sometimes medicinal odor with a lasting sweet-balsamic undertone. The oil finds extensive use in hair tonics, after-shave lotions as well as other men s-type fragrances. There is Htde or no use by the flavor industry. The range of components for a number of bay leaf oils is shown in Table 25 (66). 

Hydrocarbon impurities can be introduced by contamination of the outer surface of the candle if mold release compounds are used. Candles are sometimes shaved to reduce such contamination. 

---